Asynchronous
-
Product
4 Serial Communication Channels, Multi-Mode Programmable, Isolated
SC2
-
Module SC2 supports intelligent, full duplex, independent, multi-channels that can be individually software-configured for either RS-232C, RS-422, RS-485, RS-423 (w/data and/or clk bit inversion for MIL-STD-188C unbalanced interface support), or synchronous or asynchronous communications.
-
Product
RS-422/485 Serial Communication Card
LPCI-COM-1S
-
The PCI-COM-1S is a single port asynchronous serial communications card that can be installed in any 3.3V or 5V PCI slot computer. The card meets the MD1 PCI Low Profile Specification and is just 4.7 inches long. For low profile systems please use P/N LPCI-COM-1S for the card to be shipped with a low profile bracket.
-
Product
USB-485/4, 4-Port, USB, RS485/RS422 Serial Interface Device
778476-14
Serial Interface
The USB‑485/4 interface transforms your USB port into a single asynchronous serial port for communication with RS485 and RS422 devices. You can use a USB‑485/4 port as a standard serial port from your application, including RTS/CTS hardware handshake lines. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
PC based Serial Data Analyser
FSA32
-
This PC application is a tool to monitor and display asynchronous serial data. It can also transmit messages and monitor and set control lines. It has comprehensive triggering facilities, and runs on Windows 95 or later.
-
Product
Efficiency Test
-
Type test stands for industrial electric motors*Testing of 1-phase and 3-phase asynchronous and synchronous motors up to 3 kW*Speeds up to 30000 1 / min
-
Product
Domino Symphony PCIe
-
Four 10-bit 65 MHz A/D converters with four 8- or 10-bit LUTsPCIe x1 busD³ technology for extremely low synchronization jitterSupport for mega-pixel progressive-scan and interlaced cameras, asynchronous reset and exposure controlTrigger, strobe and general purpose I/O lines
-
Product
IP-OCTALPLUS232
-
IP-OCTALPLUS232 implements eight EIA-232 asynchronous serial ports, each with RXD, TXD, RTS, and CTS signals. In addition, two ports also have DCD, DTR, DSR, and RI signals. The serial ports are implemented with two Exar ST16C654 quad UARTs. Each channel has two 64-character FIFOs to allow longer interrupt servicing latencies.
-
Product
2-Port Serial Interface
APCI-7420-3
-
*RS232, RS422, RS485, 20 mA Current Loop (active, passive) with or without optical isolation*Modular structure through MX-modules*With or without optical isolation*Mode configuration free for each port*128-byte FIFO-buffer common interrupt*Automatic direction recognition for RS485*Transmission mode: asynchronous, full, half duplex
-
Product
Phoenix Camera Link Frame Grabber (D48-PE1)
AS-PHX-D48CL-PE1
-
Phoenix-D48CL x1 is a PCI Express board for the acquisition of digital data from a variety of Camera Link sources, including digital frame capture and line scan cameras. It supports all the formats of the Base and Medium configurations, i.e. single 8- to 16-bit data, through 12-bit RGB, to four tap 12-bit sources, as well as dual Base configuration, i.e. acquisition from two asynchronous Base cameras.
-
Product
Single Port RS232 Serial Communications Compact Flash Card With Ruggedized Connector
CF232-R
-
The CF232 is a tiny Type I format Compact Flash (CF+) single RS232 asynchronous serial port for your PDA, laptop (with an optional adapter), or desktop (using one of Elan's Desktop PCMCIA adapters). The card automatically configures to become another COM port by using the built-in O.S. drivers that are tried and tested and are optimized to work in the Windows environment.
-
Product
MC-MLPPP Analyzer And Emulator
-
The Point-to-point protocol (PPP) is a link layer protocol, which encapsulates other network layer protocols like IP for transmission on synchronous (like T1/E1) and asynchronous communications lines. When transmitted over T1/E1 line, PPP frames are based on HDLC frame structure. Two major features of PPP protocol are:*Authentication*Encapsulation of higher layer protocols
-
Product
USB-485/4, 4-Port, USB, RS485/RS422 Serial Interface Device
778476-94
Serial Interface
The USB‑485/4 interface transforms your USB port into a single asynchronous serial port for communication with RS485 and RS422 devices. You can use a USB‑485/4 port as a standard serial port from your application, including RTS/CTS hardware handshake lines. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
Fifo Serial Analyzer for DOS
FLL
-
FLL is a DOS based protocol analyzer for debugging serial asynchronous communication. FLL uses the standard COM1 and COM2 ports of a PC and does not require any other hardware except for the physical connection to the line.
-
Product
16-Bit Multi-Function With A/D, D/A And Digital I/O Channels CPCI Cards
GX3232 Series
cPCI Card
The GX3232 is a multi-channel 16-bit, analog input and output cPCI module, supporting 32 single-ended or 16 differential input channels and four analog output channels. The inputs can be software configured for differential or single-end operation and are sequentially scanned with a maximum aggregate scan rate of 300 kS/s. Three input ranges are software-selectable: ±10 V, ±5 V or ±2.5 V. Optionally, the GX3232 is available with a high voltage input configuration and supports three ranges: ±60 V, ±30 V and ±15 V. The high voltage configuration supports 16 single-ended or 8 differential input channels for high voltage and 16 single-ended or 8 differential inputs for low voltage measurement. Four analog output channels provide software-selectable output ranges of ±2.5 V, ±5 V or ±10 V. The outputs can be updated either synchronously or asynchronously and support waveform generation. Each output can be clocked at rates up to 300 kS/s. A 16-bit digital I/O port is also provided, which supports 16 bidirectional data lines. Note that when used with a TS-700 system only 8 of these digital I/O lines are available at the test system's receiver interface.
-
Product
3U CompactPCI 8-port Serial Communication Module
cPCI-3548
Communications Module
- Supports 32-bit/33MHz CompactPCI bus- 16C550A compatible serial communication controller- Eight RS-232/422/485 asynchronous communications ports with intelligent buffer- 2500 VDC signal to ground isolation voltage- Auto-flow control; change mode by dip switch- Plug-and-play, IRQ & I/O address automatically assigned by PCI BIOS, shared IRQ- Surge protectors; rugged DB-62 connector
-
Product
Modules
1x9 BIDI Transceiver Modules
-
The module supplies best solution of short-haul 20 km for fiber optical system and link distance. The module with the Differential PECL of 3.3 or 5 Voltage and provide the system designer with products to implement a range of ATM (Asynchronous Transfer Mode) and SONET for Telecommunication. The module was all supplied in the new industry standard 1x9 SIP package style with a Bi-directional BIDI SC ST or FC connector interface.
-
Product
Phoenix Camera Link Frame Grabber (D48-PE4H)
AS-PHX-D48CL-PE4H
-
Phoenix-D48CL x4is a PCI Express board for the acquisition of digital data from a variety of Camera Link sources, including digital frame capture and linescan cameras. It supports all the formats of the Base and Medium configurations, i.e. single 8- to 16-bit data, through 12-bit RGB, to four tap 12-bit sources, as well as dual Base configuration, i.e. acquisition from two asynchronous Base cameras.
-
Product
RS-232, RS-422, or RS-485 to Fiber Optic Line Driver
Model 8277
-
The Model 8277 is a unique asynchronous fiber optic modem whose optical interface can operate in either point to point or ring (daisy chain) configurations and whose electrical interface can also operate in point to point or multi-drop configurations depending on the user selected interface.
-
Product
Firmware for High-speed Communication
OP-FW12GA
-
OP-FW12GA is the firmware to increase the speed of monitoring test of bit synchronous communication (such as HDLC/SDLC/X.25, or CC-Link communication), SPI communication, Profibus-DP (field bus known for high-speed communication), UART (asynchronous communication, which is commonly used). By processing great part of monitoring processes by FPGA, it unfailingly captures communication data with time stamps of a microsecond rate. The interface supports RS-232C/RS-422/RS-485/TTL.
-
Product
USB-232, 1-Port, USB, RS232 Serial Interface Device
778472-01
Serial Interface
The USB‑232 interface transforms your USB port into a single asynchronous serial port for communication with RS232 devices. You can use a USB‑232 port as a standard serial port from your application, including RTS/CTS hardware handshake lines. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
Electrical Motor Control
-
For more than 60 years, AOIP is specialized in the starting and control of asynchronous cage or slipring motors over any kind of equipment and in any weather conditions.
-
Product
Universal PCI, Eight or Four-port RS-232/422/485 Serial Communication Card
LPCI-COM Series
-
The LPCI-COM Series are eight or four-port asynchronous serial communication cards designed for use in PCI bus computers. The cards support RS-232, RS-422, and/or RS-485 communications which can be selected on a port by port basis.
-
Product
High Performance Power Analyzer
2503AH
-
Vitrek’s High Performance Power Analyzer provides high bandwidth to 500kHz and typical 0.05% accuracy. The measurement channels can be configured independently (asynchronous or synchronous) allowing the instrument to be setup for your specific needs.
-
Product
Logic Analyzer
LAP-321000U-A
-
Zeroplus Technology Corperation
Sample rate (Internal clock): 200MHz asynchronous operation. Sample rate (External clock): 100MHz synchronous operation. Memory Depth (per channel): 1MbitsChannels: 32CH. Upgrade Oscilloscope to measure and decode I2C / UART (RS232C & RS485) / SPI Protocols and mixed signals. Glitch Capture Capability: 5ns. Bandwidth: 75MHz.
-
Product
Isolated Serial Communication Card
PCI-ICM-1S
-
The PCI-ICM-1S is a single port asynchronous optically isolated serial communication card that can be installed in any 3.3V or 5V PCI slot computer. Data lines are opto-isolated from the computer and from each other to assure communication even when large common mode voltages and noise are imposed.
-
Product
Die-cast Rotor Tester
AIP868X series
-
Qingdao AIP Intelligent Instruments Co., Ltd
Introducing the international testing technology and developing special sensor according to digital signal processing method, the die-cast rotor tester able to automatically analyze and judge the filling quality of die-cast rotor.This system is applied to all kinds of cast aluminum and copper rotors, such as: cast aluminum rotor of compressor motor, cast aluminum rotor of washing machine motor, cast aluminum rotor of fan motor, cast aluminum rotor of pump motor, rotor of automobile motor and three-phase asynchronous motor, etc. The main detection functions are: broken bar, fullness of the bar (thin bar, hole, bubble and porosity ), leakage between the squirrel cage and lamination, squirrel cage eccentricity, slot deviation.Test items: broken bar, thin bar, maximum amplitude value, minimum amplitude value, comprehensive value.
-
Product
RS-422/485 Serial Communication Card
PCI-COM-1S
-
The PCI-COM-1S is a single port asynchronous serial communications card that can be installed in any 3.3V or 5V PCI slot computer. The card meets the MD1 PCI Low Profile Specification and is just 4.7 inches long. For low profile systems please use P/N LPCI-COM-1S for the card to be shipped with a low profile bracket.
-
Product
OC-3/STM-1 And OC-12/STM-4 Analysis And Emulation Card(w/ GigE And USB 2.0)
LightSpeed1000™
-
Voice, data, and video traffic is exploding as smartphones, IP TV, video streaming, and "cloud" based services takeoff. A majority of the backbone transport for these applications continues to be SONET and SDH optical transmission networks. A dominant protocol for IP transport is PoS (Packet over SONET) and another is ATM (Asynchronous Transfer Mode). Both schemes are packet based, with ATM using fixed size packets of 53 bytes called "cells", and PoS using variable packet sizes closely matching to Ethernet frames. GL's LightSpeed1000™ hardware platform (PCIe Card and USB Pod) is capable of OC-3/12 and STM-1/4 wire-speed processing on quad optical ports for functions such as wire-speed recording and wire-speed playback of Unchannelized and Channelized ATM, PoS, and RAW Traffic.
-
Product
USB-485/2, 2-Port, USB, RS485/RS422 Serial Interface Device
778476-02
Serial Interface
The USB‑485/2 interface transforms your USB port into a single asynchronous serial port for communication with RS485 and RS422 devices. You can use a USB‑485/2 port as a standard serial port from your application, including RTS/CTS hardware handshake lines. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
FPGA Dynamic Probe for Xilinx FPGA
B4655A
-
Quickly access internal Xilinx FPGA signals Make incremental measurements in seconds, without changing design timing Access up to 128 internal Xilinx FPGA signals for each pin dedicated to debug Measurement can be either in State (synchronous) or timing (asynchronous) mode
