Sequencers
-
product
CAMAC-to-FERA Bridge
CFB
The WIENER CFB is an intelligent, programmable, re-configurable CAMAC-to-FERA bridge with sequencer that allows one to interface both, common and custom-made CAMAC modules to FERA-readout-based data acquisition systems.
-
product
Resilient Modulus and Asphalt Testing System
The Resilient Modulus software features built and test sequences, and the capability to specify user defined sequences. Contact stress is automatically adjusted according to the above procedures as selected. Available waveforms include haver sine, sine, square and triangular, along with a user defined waveform selection. Optional peak & valley compensation ensures proper and quick matching of the load parameters. Real time displays of the prescribed versus actual dynamic load or the dynamic deformation measurements by each sensor are always present. Deformation ratio of the two sensors, Rv (to ensure that the two deformation sensors are in agreement) and Mr are also calculated in real time. During export, curve fitting is done to fit the results to models that predict Mr as a function of σm, σd, and CP (cell pressure). Four different functions are calculated automatically
-
product
Sequence / Rotation Indicators
Phase Sequence and Motor Rotation meter detects live phase and sequence orientation of three phase power sources and industrial equipment conductors to ensure proper installation. Motor rotation function identifies rotational direction of industrial equipment such as motors, compressors and generators. Non-Contact Motor Rotation feature determines rotation of running single-phase and three-phase motors without the use of leads.
-
product
Bench/System Multi-Range DC Power Supply With Digital Control, 3 Or 4 Outputs, 315 To 420W With/without Remote Interfaces
MX Series
Three or four high performance outputs each with full functionalityRange switching gives variable voltage/current combinationsShared power mode provides double power from a single outputLow output noise and ripple via linear final regulationHigh setting resolution of up to 1mV and 0.1mAVariable OVP and OCP trips on all outputs50 setting memories per output plus 50 linked memoriesSelectable voltage tracking (isolated tracking)Selectable current meter averagingSwitchable remote sense capabilityGraphic LCD provides simultaneous output meteringNumeric or spin-wheel control of all parametersIndividual or combined output on/off control with programmable delay sequencing.3U half-rack case for bench or rack mounting (4U rack kit accessory available)RS-232, USB and LAN (LXI) interfaces (P models)GPIB option (P models only)Duplicate power & sense terminals at rear (P models)
-
product
Multifunction Meter for Electrical Installations
AMPI-530
Measurement of short-circuit loop ; Testing of differential, general and selective protections for differential current ; Measurement of insulation resistance ; Up to 10GΩ ; Voltages: 50 V, 100 V, 250 V, 500 V, 1000 V ; Measurement of earth resistance ; Bi-directional continuity test on PE cables, phase sequence ; Measurement and recording of voltage, frequency, alternating current, cosϕ, power, harmonics and THD
-
product
16 SE Or 8 Diff. Input Channels, 8 Analog Output Channels, PCI Express
APCIE-3121-16-8
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
product
ICT Software: Interactive Developmetn Encironment ICT ICE & ICT Sequencer
ICT IDE and Sequencer
The ICT software consists of two parts, the interactive development environment ICT IDE and the ICT sequencer. The IDE provides a graphical user interface for convenient creation and testing of these test sequences and allows:- Convenient management of hardware resources via topology editor- Support of several independent embedded testers for parallel test execution- Editing sequences in a text or table editor- Error highlighting during sequencing- Sequence execution (also single step) directly on a selected DUT- Debugging (single step)- Loop execution via sequences, or single steps- Optimization function with regard to waiting time and integration with Shmoo plot- detailed results output within tables as well as various results diagrams- Pin-Finder function to support adapter wiring- Automatic test program generation is available via Aster Testway
-
product
34-Channel Portable Logic Analyzer
16861A
34 channels, 350 MHz state, 12.5 GHz timing zoom, 2.5 GHz timing, 2 Mb depth standard15-inch (38.1 cm) color, touch-screen display for viewing and quickly navigating large numbers of signals and buses Built-in removable SSD drive, USB 3.0 ports and LAN for fast data transfer and storage of large amounts of data1.4 GHz trigger sequencer to ensure high-speed events are captured
-
product
Power Monitors - AC / DC Monitors
DARE has a complete line of AC or DC operated power monitors available in numerous package styles including 50 Hz, 60 Hz, and 400 Hz models. In addition, DARE has a series of external aircraft power monitors that continuously monitor the quality of electrical power in aircraft electrical systems, ground power equipment, auxiliary power units (APU?s), and other equipment for pre-determined over / under voltage conditions, over / under frequency conditions, loss of phase, improper phase sequence or phase rotation.
-
product
Automated Testing & Interoperability
SmartTest
SmartTest offers hundreds of test blocks – collections of actions that can be combined in multiple ways to create thousands of sequences to test:• Connection and disconnection• Bluetooth pairing and unpairing• Phone calls• Phonebook• Audio and moreYour test results are logged in our cloud based, secure database, where you access all test results, a library of essential reports, and supporting data in the form of protocol trace files, log files, and video captures. Added to this, our subject matter experts will provide a detailed explanation as to the causes of any faults or issues.
-
product
Power Distributor / Conditioner
AV-P2803
The "AV-P2803" is a power distributor / conditioner for equipment that uses a 3P outlet and is capable of long-term sequence operation and external control for systems including network devices.
-
product
Pneumatic and electro-pneumatic controllers
Pneumatic-mechanical sequencer and command module. Stepper. Control block for two-hand start. Local controllers
-
product
EZ-Glider Position Control Torque Arms
Equipped with position encoders, the position control torque arm is an error-proofing system that detects and eliminates costly screw-fastening errors during the assembly process. The poka-yoke system reduces the risks of improperly fastening screws, ensuring that every screw is correctly tightened in the correct sequence. In critical applications, tightening fasteners in the correct sequence ensures the reliability of the joint. The position control system is like putting the eyes and ears of a quality control manager where they are needed most – right at each work station.
-
product
Ethernet/LXI generatorNETBOX 16 Bit Arbitrary Waveform Generator - up to 40 MS/s on 4 Channels
DN2.653-04
The generatorNETBOX DN2.65x arbitrary waveform generators (AWG) is a general purpose multi-channel AWG with outstanding dynamic performance. The series includes LXI units with either four, eight or 16 synchronous channels. The large onboard memory can be segmented to replay different waveform sequences.
-
product
Installation Testers
Offers two models that verify the safety of electrical installations in residential, commercial and industrial applications. Has been developed to carry out the following safety measurements of electrical installations in accordance with EN 61557 and DIN VDE 0100: Insulation resistance, RCD tests, Low Ohm resistance, Earth ground resistance, Loop impedance, Phase sequence.
-
product
Multi-Function Transient Fault Recorder
TR-3000
The TR-3000 is the only tool you need to capture and diagnose power system anomalies. With multiple recording modes and continuous transient oscillography, you will never miss an event. The TR-3000 captures high speed transients and long term system disturbances with enough memory to give you a complete view of the system disturbance. The TR-3000 takes the place of several devices: • Fault and Disturbance Recorder • Transient Fault Location • Phasor Measurement Unit • Power Quality Monitor • Sequence of Events Recorder.
-
product
50MHz Single-Channel Pulse Waveform Generator
PM8571A
Model PM8571A is very high performance, single channel pulse/pattern generator that stretch normal pulse generators` spec to the limit, becoming by far the most advanced pulse waveform generator available in the market. In addition to its high performance pulse features, the new PM8571A generate a complete array of standard, arbitrary and sequenced waveforms which are necessities in today`s laboratories.
-
product
Toolset for NI TestStand
TS+
MESULOG TS + includes new configurable TestStand steps that simplify product characterization and validation, while reducing the time and cost of developing test sequences. With TS + , you can easily create advanced loop structures, save and replay datasets, display data dynamically, and include screenshots in your reports.
-
product
HLS Analyzer And Real-time Monitor
LSA100
HTTP Live Streaming (HLS) is an HTTP-based media streaming protocol implemented by Apple Inc. It breaks the overall stream into a sequence of small files, each containing one short chunk of an overall finite or unbounded transport stream. The client app downloads the files using HTTP protocol and reassembles the files into a continuous transport stream. Since the downloading uses only standard HTTP transactions, HLS is capable of traversing any firewall or proxy server that lets through standard HTTP traffic, unlike UDP-based protocols such as MPEG over UDP or RTP.
-
product
Knopp Phase Sequence Indicator
K-3, K-6, and K-7
Use of the Knopp K-3 Phase Sequence Indicator saves man-hours and protects valuable equipment against damage. It pays for itself in a short time. Specially designed induction motor unmistakably indicates the phase sequence by direction of rotation or rotor disc.
-
product
16 SE Or 8 Diff. Input Channels, 4 Analog Output Channels, PCI Express
APCIE-3121-16-4
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
product
PCIe Digital Waveform Acquisition with Programmable Threshold - 720 MBit/s Internal Sampling Rate Timing, 700 MBit/s External State Clock
M4I.7730-X8
The M4i.77xx-x8 series digital waveform acquisition (logic-analyzer) cards include versions with 32 synchronous channels, either single-ended with programmable threshold levels or differential. The large onboard memory can be segmented to record different waveform sequences. While the M4i.77xx cards have been designed using the latest technology they are still software compatible with the drivers from earlier Spectrum digital acquisition cards. Therefore existing customers can use the same software they developed for a 10 year old 60 MS/s digital input card also for an M4i.77xx series 720 MS/s logic analyzer.
-
product
Vision Data Acquisition and Management Software
Vision is the only software package available for ferroelectric testers that provides exceptional freedom to design, conduct, and review all procedures associated with any material experiment.The Vision test environment will collect all of the data acquired in a test sequence and organize it in archived data structures along with the test sequence definitions and data analysis tools, so that the experiment can always be recalled or reproduced.
-
product
Insulation/Withstand Testers/Hipot Testers
Supports remote control For automatic multipoint testing of insulation / withstand voltage Use with the 3153''''s program or with general-purpose logic sequencers
-
product
IO-Link Sensors for Motion Control
Encoder for precise position determination and linear measurement, Defined pulse sequence for the reliable detection of rotational speeds, Inclination sensors for precise measurement of angles of inclination on X and Y axes, High measurement accuracy across the total angular range in two axes, High protection rating for the requirements of harsh industrial environments
-
product
AC Clamp Power Meter
CM3286 Series
Measure power ranging from 5 W at a low current of 60 mA to 360 kW. In addition to current, voltage, and power, measure simple integral power consumption and phase sequence. Discover manipulation of electric meters by comparing meter and integral power consumption measurements. Discover theft by measuring leakage current.
-
product
Power Distribution Unit with Switchable Outputs, Soft Start & Integrated Ethernet Switch
PDU-200
The PDU-200 is a power distribution unit for automatic tests equipment (ATE). Its outputs are software controlled to allow power on sequencing and direct interaction form the test sequence. The integrated 24V power supply provides power for additional equipment like relays and sensors. The PDU-200 is intended to use with an external remote-control panel which provides On & Off buttons as well as an E-Stop and acknowledge button. It’s integrated eight port switch simplifies wiring as no additional components are required.
-
product
Touch Posi-Control System V2
DPC
The position control torque arm system helps manufacturers detect and eliminate costly screw-fastening errors during the assembly process. This position control system is designed to reduce the risk of improperly fastened screws, ensuring that every screw is in the correctly tightened in the correct sequence. A good tightening sequence ensures that an even preload distribution is achieved in the joint. Using a position control system is like putting the eyes and ears of a quality control manager where they are needed most - right on the assembly area.
-
product
MCB Instantaneous Trip Test Bench
The SCR Elektroniks MCB Instantaneous Trip Test Bench is designed for Testing of MCB to carry out “Test of Instantaneous Tripping and of correct opening of the Contacts” as per IEC: 60898-1:2002 Clause 9.10.2 at rated voltage. This test is carried out with power factor between 0.95 and 1 with the sequence operation being O-t-CO-t-CO-t-CO with timings as specified in 9.12.11.1.
-
product
VLF Testing and Diagnostics Unit
Viola TD
BAUR Prüf- und Messtechnik GmbH
Cable testing and diagnostics with the BAUR viola TD. The portable and high performance high-voltage testing and diagnostics device is available in two different configurations:viola: Used for cable and cable sheath testing of electrical equipment and medium-voltage cables up to 35 kV. Another function is insulation testing on electrical equipment. viola TD: Expands the functional scope of viola with the tan delta diagnostics and Monitored Withstand Test (MWT) that combines the cable testing and dissipation factor measurement. This allows for an accurate and comprehensive assessment of the cable condition.* Cable testing and dissiation factor diagnostics in one device* High performance and compact* Easy and quick test setup* Automatic testing and diagnostic sequences
