Sequencers
-
product
Automatic testing with National Instruments TestStand
TestStand from National Instruments is standard software for automated testing. Complex, variable test systems can be built here by integrating various hardware and software modules (e.g. LabVIEW VIs, C # modules). We can easily integrate created LabVIEW VIs into TestStand for a product-specific test sequence. All functions that are required for an automatic test sequence are available. Parameters can be changed in the TestStand environment. The user interface can be adapted to your needs.
-
product
Touch Screen Mini OTDR, 1310/1550nm
TR1200 Series
Shenzhen Sharingtek Communication Co., LTD
1. 4.3-inch multi-touch capacitive screen support zoom function screenshot2. Intelligent multi-function 12-in-one functional module: automatic OTDR expert OTDR event map optical power meter visible fault locator adjustable light source optical loss test RJ45 sequence test RJ45 length test RJ45 digital tracker flashlight end face detection (optional)3. Automatic OTDR no complicated settings one-key test4. Expert OTDR professional measurement mode simultaneous display of curve list and MAP view5. Event blind zone 2.5m attenuation blind zone 8m measuring range up to 100KM6. Support optical test with optical signal less than -5dBM high isolation bilateral filter technology7. Support automatic saving SOR file format 8G storage capacity 200000 records can be stored8. Support Type-C charging interface 4000mAh polymer battery battery life is more than 12 hours
-
product
Distance Measuring Equipment (DME)
MS 2002
Distance measuring equipment (DME) is a transponder-based radio navigation technology that measures distance by timing the propagation delay of UHF radio signals. The DME system is composed of a UHF transmitter/receiver (interrogator) in the aircraft and a UHF receiver/transmitter (transponder) on the ground. The aircraft interrogates the ground transponder with a series of pulse-pairs (interrogations) and the ground station replies with an identical sequence of reply pulse-pairs with a precise time delay (typically 50 microseconds). The time difference between interrogation and reply minus the 50 microsecond ground transponder delay is measured by the interrogator's timing circuitry and translated into a distance measurement in nautical miles which is then displayed in the cockpit.
-
product
VLF Diagnostics System
PHG 70 TD
BAUR Prüf- und Messtechnik GmbH
Cable testing and diagnostics with the BAUR PHG 70 TD. The combination of the PHG 70 programmable test generator with the BAUR dissipation factor measurement system produces the cable testing and diagnostics system PHG TD. It is operated via PC control. Dissipation factor measurement and diagnostic testing sequences can be programmed in the menu, after which the dissipation factor measured values are automatically determined in various voltage steps and a final evaluation is conducted.* Biggest dynamic range of tan delta measured values from 1 to 10-4 with a cable capacitance >10 nF to 20 uF* High resolution +/- 1x10-5 applicable even in new PE/XLPE cables* Insensitive against interferences due to complete mains separation* Lowest time required for assessing a medium-voltage cable (3-phase approx. 1 hour)
-
product
Camera Test System
FS 8681 / SR
FS8681/SR is software for evaluating images* and making pass/fail judgments in camera mass production inspections. It consists of the "Editor FS8681" application that sets the inspection content and the "Sequence Runner FS8681SR" application that executes the set inspection.
-
product
Bench Electronic Loads
EL30000 Series
The Keysight EL30000 Series Bench electronic load with a built-in data logger provides new levels of test insights for your devices like power supplies, batteries, DC to DC converters, and more. View voltage and current trends to make real-time decisions, rather than waiting hours for a test to complete. At the heart of the EL30000 is a highly accurate measurement system that provides real-time updates to the large display. Keysight’s PathWave BenchVue software allows you to operate the electronic load remotely, execute test sequences, log data, and integrate with other test instruments. Single and dual-channel models are available with up to 600 W for measurements that require more power. Start your test with confidence and finish with results you trust.
-
product
Super Phosphor Oscilloscopes
SDS5000X Series
The SDS5000X series employs Siglent’s SPO technology with a maximum waveform capture rate of up to 110,000 wfm/s (normal mode, up to 500,000 wfm/s in Sequence mode), 256-level intensity grading display function plus a color temperature display mode. It also employs an innovative digital trigger system with high sensitivity and low jitter. The trigger system supports multiple powerful triggering modes including serial bus triggering. History waveform recording, Sequence acquisition, Search and Navigate functions allow for extended waveform records to be captured, stored, and analyzed. An impressive array of measurement and math capabilities, options for a 25 MHz arbitrary waveform generator, as well as serial decoding are also features of the SDS5000X.
-
product
Universal Safety- & Function Tester
GLP2-BASIC
The variety of features, e.g. to create your own test sequences, to enter your own data as serial number, result storage, freely configurable label print out, barcode function and many more leave nothing to be desired.
-
product
AC Power Sources
8500 Series
The EEC 8500 Series is the most power dense and functionality rich power source in our history, giving you improved capability, functionality, and a reduced footprint all in one series. This series is manufactured or simulating common grid faults, voltage dips, and other power abnormalities. The 8500 Series provides an output voltage up to 310VAC and an output frequency ranging from 5 Hz – 1,200 Hz making it the obvious solution for all kinds of applications. Not to mention, an enhanced interface to all models completely designed with the end-user in mind. Our 8500 Sources can be configured as a simple AC Power Source in MANUAL mode, as an upgraded option with Standard mode or incorporating all functions with Advanced Mode. Advanced mode adds the benefits of a sweep of voltage, frequencies, transients, and DC bias over the course of a single sequence or several different tests. The 8500 Series includes the following models: 8505, 8512, 8520, 8530, 8540, & 8560.
-
product
Hardy Shaker
HI-903
This is our top of the line Hardy Shaker. It provides the ability to set the amplitude and change the frequency range without the amplitude changing. This automation makes conducting vibration tests easier. Tests can be conducted on multiple vibration transducers, and then the saved data can be transferred via USB Flash Drive to be displayed in an automated and customizable report using an Excel template on your computer. In manual mode, the vibration test level and test frequency can be set from 7 Hz to 10,000 Hz. The high accuracy instrument can display the vibration level in terms of g’s peak, velocity peak (in/sec or mm/s) or displacement peak-to-peak (mils or µm). The unit can support payloads up to 800 grams (see frequency limits in the manual). A built-in display reads the output sensitivity, which can be stored in memory. Complete testing sequences and data can be stored in memory for each tested sensor, the unit logs the data on the spot or stores it for later use. For testing of heavy transducers or at high frequencies, the HI-903 automatically corrects the sensitivity calculation for the effects of transducer mass loading. A built-in self-test program checks for accuracy of all calculations. The HI-903 has a built-in battery charger that can operate on 120 or 240 VAC. The unit comes in a rugged Pelican case.
-
product
BERT Measurement Solutions
Bit error rate testers (BERTs) are usually the initial step for communications testing. These instruments generate digital test patterns, typically pseudorandom binary sequences (PRBSs), that drive devices under test (DUTs). Following the transmission of the signal through the link, the receiver in the BERT captures the signal. This setup can be used for multiple testing purposes, such as to evaluate the performance of a transmitter, a receiver, or an optical link.
-
product
12-bit, 200KHz, 16SE/8DIFF Isolated AI, 4 12-bit AO, 8 Optically Isolated Dig. I/O, 24V, 24 TTL I/O
APCI-3110-16
The APCI-3110 is a 12-bit multifunction board for 3.3 V and 5 V PCI systems, with optical isolation up to 1000 V and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.Furthermore, the board has a PCI DMA, 2 watchdogs, 4 digital inputs and 4 digital outputs. Sensors, which allow to supply current signals instead of voltage signals, also can be acquired with the APCI-3110, as this board offers up to 16 current inputs. The board is protected against overvoltage and input filter and it is protected against high frequency emmission. With the free calibration tool you can do the fine adjustment on-site.
-
product
UTP Software Suite
Increasing customer requirements, shorter product cycles and higher time to market demands dramatically influence the long-term goals in software development. With the Universal Test Platform Software Suite (UTP Suite), we introduce a robust standard that features a great set of tools for configuring, developing, analyzing, debugging and executing test sequences.
-
product
ARINC 664 Part 7 PXI Express Test & Simulation Instrument
PXIe-C664-V2
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfaces - Simulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K - Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequencing & periodic data generated onboard - Error Injection including Runt Frames, Short IFG, and Invalid MAC FCSDevice driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
Phase Sequence and Motor Rotation Tester
TKF-13
The TKF-13 tester is a modern high-quality, simple and safe device. However it is recommended to et acquainted with the present manual in order to avoid measuring errors and prevent possible roblems related to operation of the meter.
-
product
Dynamically Controlled High Speed Digital I/O PXI Card
GX5150 Series
The GX5150 Series are high speed, 6U PXI, sequenced digital I/O instruments. The GX5150 master controller has 32 bits of I/O channels that supports test rates of up to 50 MHz and a vector depth of up to 128 Mb per pin. The GX5151 slave offers the same timing characteristics and multiple I/O level configurations when used in conjunction with the GX5150. The GX5150 can control up to 15 GX5151 boards using the same timing and sequencer.
-
product
Automatic Wire Test Set
AWTS
The Automatic Wire Test Set (AWTS) is automated test equipment that aids wiring diagnostics of electrical and electronic devices. The Test Control Unit (TCU) uses resistance measurements, capacitance measurements, and AC/DC voltage measurements to perform continuity, insulation, and isolation tests. The AWTS Laptop CPU, hereafter referred to as CPU, controls the AWTS. The Eclypse Language Integrated Test Environment (ELITE) is application software that controls the TCU. The majority of the hardware for a test is contained in the TCU. The 128pin connector on the TCU front panel provides 128 energizable test points. Switch Modules (SM) can be connected in sequence or daisy chained to the TCU and provide an additional 1024 test points; 128 of those are energizable.
-
product
Rolling Seal 4 Optical Connector
RS4
- GAF/ELI enhances mating efficiency and eliminates potential for shell damage while offering positive latch indication.- Longer, contoured cable end lead-in bushing enhances fine alignment of connector halves during the mating sequence.- Reduced channel count to align with more efficient field architectures.
-
product
PXI-4132, 100 V, 2 W Precision PXI Source Measure Unit
780558-01
±100 V, 10 pA Precision PXI Source Measure Unit—The PXI-4132 is a programmable, high-precision source measure unit (SMU). It has a single isolated SMU channel that offers a four-quadrant output that incorporates remote (4-wire) sense as well as external guarding. With its high measurement resolution integrated guarding, the PXI-4132 is ideal for high-accuracy leakage measurements on integrated circuits, discrete components, PCBs, and cables. You can also perform high-speed I-V measurements on a variety of components including diodes and organic LEDs using the onboard hardware sequencing engine. In addition, you can synchronize multiple PXI-4132 modules using the PXI backplane to provide high-speed I-V measurements on transistors and more complex devices.
-
product
Multiplex Temperature Tester
TMP-8/TMP-16
• 8 channels temperature signal (TMP-8) or 16 channels temperature signal (TMP-16) • T type or K type thermocouple • Temperature range: -40 ~ 300°C. Testing accuracy: 0.5% • Channel sequence is displayed by 2 LED and temperature is displayed by 4 LED • Freely set up the software with PC and record the change of temperature and select the channel.
-
product
Phase Sequence and Motor Rotation Tester
PRM-6
The PRM-6 Motor and Phase Rotation Tester can test the motor rotation of 3-phase systems, and verify 3-phase receptacle wiring and phase sequencing with test leads.
-
product
AID and Data Collection Board for IP Cameras
FLIR VIP-HD
The FLIR VIP-IP is a multi-functional Video Image Processing module for traffic control. VIP-IP boards process video input from D1 resolution IP cameras for automatic incident detection, data collection, recording of pre and post incident image sequences and streaming video (single H.264, MPEG-4, MJPEG). VIP-IP boards have been installed for road and tunnel projects all over the world.
-
product
1Gsps, 9 Channel, Logic Analyzer with Protocol Analyzer plugins and Hardware Compression
DigiView™ DV509
- Physical Channels: 9- Sample rate: 4ch@1 Gsps or 9ch@500Msps (4 ch. are sampled every 1ns or 9 ch. are sampled every 2ns)- Typical capture: 100M transitions (> 1B samples)- Hardware based triggers with 8 universal match circuits, and partitionable 16 stage sequencer- Adjustable Threshold (± 4V)- Real-time, Hardware-based, Adaptive Compression- Channels protected to ± 20V- Ground leads protected to ± 12V- High-quality test leads: 66 strand soft copper wires, flexible insulation, and gold plated connectors. Fit .025 square posts as well as the included clips.- Extra ESD protection- Streaming storage with auto fall-back to Store & Forward mode ensures large storage and reliability.- USB 3.0 (SS) or USB 2.0 (High Speed)- USB powered- Each DigiVIew includes all avialable Protocol Analyzer plugins (including: I2C, SPI, CAN, Async, Sync, 1-wire, I2S, TDM)- Free Plugin Developers' Kit- Requires Windows 7 or greater OS (32bit or 64bit)- Free Lifetime sofware updates.- 1 year warranty
-
product
Non-contact Phase Sequence Detector
Phase detection (normal phase, reverse phase and phase deficiency), Live wire examination, Simple Power detection, Breakpoint location and Line maintenance.
-
product
Dual-Port HS-1760 Test & Simulation PXI Express Module
PXIe-C1760
Avionics Interface Technologies
3U PXI form factor fits into PXIe or PXI hybrid slotTwo independent ports programmable as NC or NT(s) simultaneouslyTwo SFP sockets accepts FC-0 AS5653 or AS5625/AS5627 transceiversSupports NC-to-NT transfers, NT-to-NC Transfers, Mode Codes, and BroadcastFull control of sequence and exchange managementSupports large file exchangesFull Monitoring of all Bus TrafficTriggering and FilteringFull Error InjectionSupports DMA for high speed streaming of data to/from the boardIRIG-B Time Code Encoder/Decoder for Data CorrelationOptional Special FC-0 physical layer compliance with SAE AS5653Optional fcXplorer Analyzer for decoding HS1760 frames
-
product
3D Semiconductor & MEMS Process Modeling Platform
SEMulator3D
SEMulator3D® is a powerful 3D semiconductor and MEMS process modeling platform that offers wide ranging technology development capabilities. Based on highly efficient physics-driven voxel modeling technology, SEMulator3D has a unique ability to model complete process flows. Starting from input design data, SEMulator3D follows an integrated process flow description to create the virtual equivalent of the complex 3D structures created in the fab. Because the full integrated process sequence is modeled, SEMulator3D has the ability to predict downstream ramifications of process changes that would otherwise require build-and-test cycles in the fab.
-
product
Time-Lapse
The Time-Lapse app enables you to use an Android Device to record a sequence of images from your ioLight microscope automatically. The app records images at regular intervals of a few minutes to days.Time-Lapse is great to use with the Inverted Microscope to monitor the growth of cells and cultures in incubators.
-
product
Ethernet/LXI generatorNETBOX 16 Bit Arbitrary Waveform Generator - up to 125 MS/s on 12 Channels
DN6.656-24
The generatorNETBOX DN6.65x arbitrary waveform generators (AWG) is a general purpose multi-channel AWG with outstanding dynamic performance. The series includes LXI units with either up to 48 synchronous channels. The large onboard memory can be segmented to replay different waveform sequences.
-
product
Aircraft Escape Systems
The Emergency Interseat Sequencing System (EISS) was designed an qualified for the F-15K Fighter and has since been installed in the F-15SG and F-15SA configurations of the F-15. The system consists of Thermal Batteries with Initiators, a Digital Interseat Sequencer, Mode Selector, and customer provided cabling Electro-Explosive Devices (EEDs). The system is operated from either thermal battery and aircraft 28Vdc for redundancy. A separate field Test Set (EESSTS) performs both complete system continuity tests and an operational test of the total system installed in the aircraft. The sequencer is programmable and could be used in any escape system.Based on the initiation point, Forward or Aft Seat Handle, Internal or External Canopy Jettison Handles, and the Mode Selector setting, the Sequencer provides firing pulses to the EEDs to support canopy removal, ejection seat inertial reel activation(s) and ejection seat catapult firing(s). Sensing capabilities are provided to determine system state, canopy gone, seat gone, so as to provide the optimum escape timing.
-
product
COMPUTERIZED AUTOMATIC RELAY TEST SYSTEM
CVRT-S16
CVRT-S8 & S16 are ideal for automatic testing of ELECTRO MECHANICAL AND READ RELAYS (only DC relays) both for static and dynamic characteristics. This system scans at one stroke, all the parameters of the relay as per definition of test procedure. The test sequence can be pre-programmed and stored in the disk. You can select the tests as per your requirement. Can include or exclude the test and you can have several options to match your test definitions. Semi skilled person can be engaged for actual testing, as he need not make any settings and need not interpret the readings. The system conducts the tests and gives PASS / FAIL indication on overall test results. If a printer is connected, each test result will be printed.Test Parameters : -> Coil Resistance.-> PickUp/Pull In /Operating Voltage or Current Linear Ramp Method or Step Method.-> Measure Pickup Contact Gap FBB-LBB V or mA-> DropAway/Drop Out/Release Voltage or Current Linear Ramp Method or Step Method.-> DropAway Contact Gap FFB-LFB V or mA-> % Release Dropaway/Pickup-> Contact Resistance of all contacts both Front and Back contacts.-> Operating Time @ Set Voltage or Current.-> Contact Bounce or Chattering Time while Operating @ above-> Release Time @ Set Voltage or Current.-> Contact Bounce or Chattering Time while release @ above-> Difference of Operate Time - Release Time.-> Bridging Test or Non Overlap Test.-> Transfer or Traverse Times while Operate and release.-> Operate Time @2nd Set Voltage or Current.-> Release Time @2nd Set Voltage or Current.-> Power Consumption @ Rated Voltage.-> Coil Current @ Rated Voltage at Room Temperature.-> Coil Resistance Corrected to 20deg C.-> Timing Waveform Graph for all active Contacts.
