-
Product
Signal, Patchcord, Receiver, 36", TriPaddle, 22 AWG White, Single Ended ( 5 Amps)
7-104962000-036
Signal Patchcord
Signal, Patchcord, Receiver, 36", TriPaddle, 22 AWG White, Single Ended ( 5 Amps).
-
Product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Tinned Ends
A050DF5-T-0A200
Cable Assembly
The 50-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated wire and can be secured to the product by screwlocks. The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
Audio Line Drivers and Receivers
-
Analog Devices audio line driver and receiver solutions feature differential-output buffer amplifiers and differential input buffer amplifiers to support a wide range of applications. By using low noise thermally matched thin film resistors and high slew rate amplifiers, these parts maintain the sonic quality of audio systems by eliminating power line hum, RF interference, voltage drops, and other externally generated noise commonly encountered with long audio cable runs. Applications involving this product portfolio include ADC drivers, high performance audio, sine/cosine encoders, and other professional and consumer uses.
-
Product
End-to-End Network Monitoring
OSIX
-
Network monitoring with tracing and troubleshooting capabilities to achieve first-class customer experience and to proactively prevent network and service quality degradation. OSIX Monitoring enables Communication Service Providers (CSPs) to detect and resolve network issues or poor performance before end-customers are affected.
-
Product
Cable Assembly, 78-Pin D-Type, Female to Unterminated With Cut Ends
A078HF5-C-0A050
Cable Assembly
The A078HF5-C-0A050 is a 78-Pin D-Type to Unterminated cable assembly constructed from 7/0.15 (26AWG) Silver Plated Copper Wire. Screwlocks are provided to secure the cable connector to associated products. Has a 45 degree cable exit towards pin 1.
-
Product
Power Line Isolators & Conditioners
-
A power line conditioner (also known as a line conditioner or power line conditioner) is a device intended to improve the quality of the power that is delivered to electrical load equipment. While there is no official definition of a power conditioner, the term most often refers to a device that acts in one or more ways to deliver a voltage of the proper level and characteristics to enable load equipment to function properly.In a nutshell, poor incoming electrical power converted to good output power.
-
Product
Cable Assembly, 37-Pin D-Type, Male to Unterminated With Tinned Ends, 2m
A037DM5-T-0A200
Cable Assembly
The 37-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) wire and can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation . Please ensure appropriate electrical safety precautions are observed when using this product.
-
Product
Cable Assembly, 160-Pin DIN41612, Female to Unterminated With Cut Ends, 0.5m
A1604FR-C-0A050
Cable Assembly
A range of DIN41612 cable assemblies with unterminated connections on one end. For applications in LXI products where 4 connectors are used in a horizontal row if the user requires all connectors to have a second fixing then the right hand connector can be fitted with the optional screwlock assembly 40-969-101.
-
Product
3-Pin Power D-Type Cable, Female to Unterminated, Tinned Ends, 1m
A003PF4-T-5A100
Cable Assembly
The 3-Pin Power D-Type cable assembly is constructed from 50/0.26mm2 (14 AWG) Tinned Copper Wire with PVC insulation. Screwlocks are provided to secure the connectors to their associated products.
-
Product
Cable Assembly, 160-Pin DIN41612, Male to Unterminated With Tinned Ends, 1m
A1604MR-T-0A100
Cable Assembly
This cable assembly is not suitable for direct connection to Pickering Interfaces switching products.
-
Product
Cable Assembly, 25-Pin D-Type, Female To Unterminated With Tinned Ends, 0.5m
A026HF4-T-0A050
Cable Assembly
26-Pin Female to Unterminated D-Type Cable Assembly with Tinned Ends. 0.5m Long.
-
Product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Cut Ends, 2 Amp, 1m, 250 Port
A500RMR-C-4B100
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products. Unterminated connections are provided at the other end of the cable for a variety of applications. Screwlocks enable the SEARAY connector to be secured to its mating product.
-
Product
Party Line Intercom Conversion
COMMS Series
-
The stand-alone COMMS 300 and the OG-COMMS openGear® units provide a means to interface between two channels of 2-wire party-line intercom audio and two channels of 4-Wire analog line-level signals. The unit is capable of performing auto nulling for each channel with the push of a button. In addition, each of the 4-Wire input and output channel levels are monitored and displayed on easy to understand front panel VU meters.
-
Product
Power, Patchcord, Receiver, 72", Mini Power, 16 AWG White, Single Ended (19 Amps)
7-234916000-072
Power Patchcord
Power, Patchcord, Receiver, 72", Mini Power, 16 AWG White, Single Ended (19 Amps).
-
Product
20-Pin Scorpion Cable, Female to Unterminated, Cut Ends, 30A, 0.5m
A020AFR-C-3A050
Cable Assembly
This is a 0.5m long female to unterminated 20-Pin Scorpion cable assembly with cut ends constructed from 37/0.4 (10AWG) Silver Plated Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product.
-
Product
Cable Assembly 68-Pin Micro-D Male to Unterminated, Tinned Ends, 1m, Spring Latch
A068SMR-T-5B100
Cable Assembly
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by a Metal Spring Latch.
-
Product
Cable Assembly 68-Pin Micro-D Female to Unterminated, Cut Ends, 0.5m
A068SFR-C-6A050
Cable Assembly
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by 2-56 UNC Screwlocks.
-
Product
Platiunum Tools TelScope Telecommunication Line Analyzer Test Set
#TLA300-1
-
The TLA300-1 TelScop is a telecommunication line analyzer for POTS butt sets.
-
Product
Micro Coax, Patchcord, ITA, 50 Ohm, 36", RG316 Tan, Single Ended
7-361116000-036
Coax Patchcord
Micro Coax, Patchcord, ITA, 50 Ohm, 36", RG316 Tan, Single Ended.
-
Product
Portable Connector End Face Geometry Interferometer
-
Thorlabs’ Vytran® Connect-Chek® Interferometer automatically and precisely measures radius of curvature, apex offset of polish, and fiber undercut or protrusion on any PC or APC, single-fiber connector. The CC6000 interferometer uses a non-contact tilted-phase-analysis technique for fast, reliable measurements of connector end faces. This compact interferometer has a carrying handle and must be attached to a desktop or laptop computer (not included) with a standard USB 2.0 port for operation. The included CC6000 software, which is used to control the interferometer, can be installed on a computer with the minimum requirements in the table below. Designed for use in both the factory and the field, this interferometer provides crucial quality information needed to assure long-term performance of fiber optic connectors. One CC250P Mount for Ø2.50 mm PC Connectors and one RT250P Reference Tool for calibrating the CC250P mount are included with the CC6000 interferometer; mounts and reference tools that enable measurement of other PC or APC, single-fiber connectors are available separately below. When used with an appropriate mount for APC connectors, the CC6000 interferometer is also capable of measuring the APC angle and key error.
-
Product
Cable Assembly 44-Pin D-Type Female to Unterminated With Tinned Ends, 1m
A044HF4-T-0A100
Cable Assembly
The 44-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 7/0.15 (26AWG) Silver Plated Copper Wire. The connector can be secured to the product by screwlocks.
-
Product
High End Current Sensors
-
AC and DC currents with an accuracy down to 1ppm. Our standard products offers the following features: Automotive current sensors. Extended temperature current sensor - 85 deg Celcius. AC current sensor - DC current sensor.
-
Product
Coax, Patchcord, ITA, 36", Mini Coax, RG316 Tan, Single Ended
7-331116000-036
Coax Patchcord
Coax, Patchcord, ITA, 36", Mini Coax, RG316 Tan, Single Ended.
-
Product
Fault Passage Indicator for Lines
LineTroll R400D
-
LineTroll R400D Fault Indicator indicates earth- and short-circuit faults and can distinguish between permanent and transient faults. The indicator has two sensors and use both the electrical field and the magnetical field to detect faults on all three phases.
-
Product
Cable Assembly 44-Pin D-Type Female to Unterminated With Tinned Ends, 2m
A044HF4-T-0A200
Cable Assembly
The 44-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 7/0.15 (26AWG) Silver Plated Copper Wire. The connector can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation. Please ensure appropriate electrical safety precautions are observed when using this product.
-
Product
Cable Assembly, 9-Pin D-Type Male to Unterminated With Cut Ends, 1m
A009DM5-C-0A100
Cable Assembly
A range of 9-Pin D-Type cable assemblies with unterminated connections at one end and constructed from PFA insulated wire. The connector assembly can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation.
-
Product
Power, Patchcord, ITA, 72", Mini Power, 50µ, 16 AWG White, Single Ended (19 Amps)
7-235916000-072
Power Patchcord
Power, Patchcord, ITA, 72", Mini Power, 50µ, 16 AWG White, Single Ended (19 Amps).
-
-
Product
Cable Assembly, 37-Pin D-Type, Male to Unterminated With Cut Ends, 1m, HV
A037DM5-C-HA100
Cable Assembly
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Cable Assembly 68-Pin Micro-D Female to Unterminated, Tinned Ends
A068SFR-T-6A100
Cable Assembly
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by 2-56 UNC Screwlocks.
