-
Product
End of Line Test System for Automotive Seats
AS519
Test Platform
AS519 is specifically designed to perform ECU’s EOL tests in the automotive industry. It integrates a programmable power supply up to 20V 20A with high reading resolution. Interaction with the DUT is established through CAN bus by an interphase adapter in a USB port of the test managing computer.
-
-
Product
Multifunctional Safety Tests
-
Manufacturers of electrical or electronic products are required by law to carry out an electrical safety test before placing them on the market. This final test takes place at the end of the manufacturing process and is therefore also referred to as an EOL test (end-of-line). Depending on the prescribed standard and directive, the following parameters are tested:- Leakage current and discharge current- Insulation resistance or the insulation strenth- Dielectric strength or electric strength- Correct installation of the protective conductor (ground continuity and ground bond test)- Faultless functioning of the product under the conditions defined for intended use (function or run test
-
Product
Automotive Battery Production Line Tester
-
The Production Line Tester (PLT) is typically installed at the end of battery production lines (finishing). An electrical load test after formation charging is essential to assure performance and quality. The energy discharged during this test must be minimized to eliminate the need for recharging after testing.
-
Product
Small Device Test Chambers
-
Small Device Test Chambers are used for basic sound level measurement of small products and equipment, pre-compliance testing of small products and equipment and end of line manufacturing test on small products and equipment.
-
Product
Testing & Quality
-
The solar simulator, electroluminescence and hi-Pot testers are the main machines used to test photovoltaic modules. These machines can be positioned at the end of the production line and along the production chain to keep the quality and efficiency of the photovoltaic modules under control after the most sensitive production phases. Each machine uses the best technologies in order to guarantee the best and most accurate measurements.
-
Product
End-to-End Flight Line Confidence Test Set
MEON™
-
MEON™ is an end-to-end flight line confidence test set for directional infrared (IR) countermeasures (DIRCM) and ultraviolet (UV) missile warning systems. It also incorporates an IR beacon and an IR detector to provide complete, end-to-end testing, alignment checks and calibrated radiometric measurement of DIRCM.
-
Product
Lumber Moisture Measurement Systems
-
Improved moisture control has emerged as an important process improvement element in the forest products industry as mills continue to focus on profitability and yield. SCS Forest Products by Finna Sensors provides the industry’s widest-used end-to-end line of integrated moisture measurement systems and related process optimization tools for the sawmill, kiln and planer.
-
Product
Data Acquisition Processor Board
DAP 5200a
-
The DAP 5200a model brings many more real-time data acquisition and control applications within the scope of Windows systems. Its onboard 400 MHz processor substantially increases the real-time processing power of the top end of the DAP line. Real-time processing functions include smoothing, filtering, FFT, PID control, and responding to alarm conditions;
-
Product
BottleChek
-
The BottleChek Metal Detector Conveyor is designed to inspect pharmaceutical bottles or vials at the end of the packaging line for unwanted metallic particles. The system easily integrates into any production line for side-by-side transfers.
-
Product
Fast LID Measurements for EOL
KMP
-
TechnoTeam Bildverarbeitung GmbH
The KMP is the solution to cost-effectively bring indirect light measurement technology to places with too little space for a BV room. Its lightweight and compact design allow it to be integrated into production lines, positioned next to production or in a small lighting lab.
-
Product
EOL Testing of Starter-Generator Units (ISG)
-
Series test rig for starter-generator units (ISG)*High voltage test*Insulation resistance measurement*Temperature sensor control*Short circuit test*EMF test*Performance measurement*Manual loading and contacting
-
Product
Systems Analysis Interface
Saint2
-
The Systems Analysis INterface Tool 2, a Delphi Preferred Tool, for Low-cost EOL Testing & Reflashing Without the Need of Additional Hardware.
-
Product
EOL RF Functional Test
AS652
Test Platform
With this RF test platform, integrable according to the specific needs of the product, we cover a very wide range of test needs with manual feeding.Ergonomics have been fully observed in the design, including the option of servo adjustment of the working height according to the operator.
-
Product
Inductor Test & Packaging Machine
1870D
-
The Chroma 1870D Series (1870D/1870D-12) are specifically Designed automated test equipment for chip inductors. It comprises Various test functions that are required for verifying chip inductors. In addition, an automated tape packaging machine at the end of production line is equipped to fulfill demand for automated manufacturing.
-
Product
Running Line Tensiometer
TIMH
-
The TIMH - running line tension meter range are built with dockside, marine, offshore, towage and salvage applications in mind. It is particularly useful where there is no anchor or dead end on the line to rig a Straightpoint Radiolink or Loadlink digital dynamometer to measure tension force.
-
Product
RF Terminators
-
Typically placed at the end of a transmission line and is designed to match the cable's AC impedance.
-
Product
Multi-Purpose Probes
-
*For All your Functional Test Needs *Machine Building *end of line test
-
Product
Radome Tester
QAR50
-
The R&S®QAR50 is the ideal tool for accurately testing the quality of automotive radomes and bumpers in the automotive radar frequency range at the end-of-line (EOL). It features sufficient space to easily accommodate bulky bumpers combined with spatially resolved measurements to evaluate the homogeneity of design emblems.
-
Product
Sound Harmonics and Current Analyzer
H74050100
Audio Analyzer
This analyzer is used as end of line control for electro mechanic components with electric motors, with or without mechanical reduction. While the motor is running at nominal speed, a spectrum and temporal analysis of the sound as well as a current consumption test is performed. Statistical analysis of the data acquired is also performed real-time, expediting the PASS/FAIL decision of the DUT.
-
Product
Transformer Tester
-
MOTOMEA Distribution Transformer Test Systems: Routine Testing for Production (EOL) and Quality Assurance (QA). Type Testing at Laboratory (R&D)
-
Product
Cycle-ATV Dynamometers
EC997
-
The EC997 Series, our standard eddy current motorcycle chassis dynamometer, takes motorcycle performance tuning to the next level. The EC997 Series uses the industry’s most advanced electronics and Dynamic Load Control technology, featuring precision closed-loop torque feedback – a standard feature with every EC997 dyno. Competitor’s dynos on the market allow you to apply “percent % load” but Mustang has perfected the art and science of Dynamic Load Control and proudly offer the most sophisticated Dynamic Load Control dynamometer available at any price. Our superior control technology combined with our ultra-low inertia design allows you to precisely control loading to hold the engine at each RPM. Try doing that with a heavy drive roller and insufficient control technology – you simply cannot! Mustang has delivered thousands of performance dynamometer systems over the past 35 years and has perfected the art and science of dynamic vehicle loading and dynamometer control. We include each motorcycle make and model in our database including weight and drag coefficients so you can simulate the track right on the dyno! While other dyno manufactures are still trying to catch up with our technology, Mustang continues to lead the industry and is recognized around the world as the industry’s best with regards to dynamic dynamometer controls. Mustang has built racing dynos for Harley-Davidson as well as several end of production line testing cells for Harley-Davidson, Honda, and Polaris.
-
Product
EOL Testing of Speed Sensors
-
Complete programming and end of measuring stations integrated in the assembly line for rotary electronic sensors with automatic sensor recognition.
-
Product
EOL Tester
-
A specialized automated system used in manufacturing to perform final functional and quality checks on products right before they leave the assembly line, ensuring each unit meets design specifications, works correctly, and complies with safety standards, covering everything from basic continuity and calibration to complex performance simulations.
-
Product
Series and EOL Testing of Electric Motors
-
Highly automated EOL test system for blind motors*Test station with fully automatic mechanical and electrical contacting *Scanning the product coding with barcode scanner*Integrated label printing, additional error printer*Contact protection by light curtain
-
Product
Press-type Vibration Tester
9363-PC-ESS
-
King Design Industrial Co., Ltd.
This machine complies with the IEC, JIS and other 5-100Hz low-frequency specifications; applied to test the post-assembly products at end of the production line. Use resonance amplification, the product’s flaws can be screened out in advance. The operation is convenient, fast and effective.Apply Japan-imported motor; durable and safe in operation.Bellow-type damper: use special damping material that can effectively absorb vibration; allowing the test to be performed without affecting floor structure.Motor drive system is embedded in the seat; good in vibration block-out; rigidity is strong. Follow specimen to design fixture.
-
Product
Function Tester with Low Number of Channels
UTP 6010 RF
-
The UTP 6010 is one of our smallest test systems and therefore a cost-effective entry into our UTP tester series.The fast system is used to implement scalable functional test applications for a test item (single device under test) with multiple RF channels and mixed-signal test options. Depending on the adapter, the DUT can be tested at circuit board level (FKT) or when installed at the end of the line (EOL).Depending on the test item requirements, we configure the appropriate number of channels and integrate the necessary interfaces directly in the adapter or tester. The test speed, production volume and overall complexity of the UTP 6010 interfaces can be varied according to your requirements.
-
Product
Load Termination
-
A process of ending a transmission line or cable to either dissipate energy as heat or prepare it for connection to a device.
-
Product
End-of-Line IC & MEMS Tester
igentic® 841t
-
Integrated circuit (IC) and micro electro-mechanical system (MEMS) device manufacturers need to address the challenges of today's global market including increased functionality, speed and complexity while delivering components at reduced costs. Sterner Automation's igentic® 841t automated test systems meet these demanding requirements by providing a flexible platform for comprehensive end-of-line IC and MEMS device handling, testing, grading and packaging. The resulting improvements in quality assurance and process efficiency will maximize customer satisfaction and profitability.
-
Product
Sealed Beam Bulb Testing System
H710019SSL
Test Platform
EOL test for manufacturing of bulbs with LED for applications requiring to ensure watertightness: vehicles, marine, swimming pools, operating rooms, classified areas (Ex Zone), etc. The test system checks in a short time all the light and electrical characteristics of the bulb. A high precision Micro Leakage Meter also checks that there are no leaks between the environment and the inside of the bulb. The test results are recorded on the PC and can be printed on a quality control label attached to each unit.
