Timing
See Also: Time, Timers, Time Interval, GPS Time, Time Reference, Time Code, Time Domain, Time Standards, Time Interval Analyzers
-
Product
Exposure Level Tester
ELT-400
-
*Wide frequency range (1 Hz - 400 kHz)*Standard-compliant measurement*Acceptance measurements compliant with CE standard IEC/EN 62233 and Generic Standard IEC 62311*Limit value traces conforming to ICNIRP 1998, 2010 and EMF Directive 2013/35/EU*Real time measurement with RMS and peak detectors*External FFT signal analysis for determining the frequency components via three channel analog output (one channel for each spatial axis) e.g. with the aid of a digital oscilloscope.
-
Product
Environmental Chamber
REXMED REC-200
-
MOD. REC-200, AC 230/380/415V, 1/3 phase, Environmental chamber, HS CODE: 841989, UNCCS CODE: 484384, UMDNS CODE: 16327, Main construction: SS304, Interior: SS304, Exterior: SS304 powder coated, Insulation: Rigid polyurethane foam and glass wool, Controller: Fix point PID controller, temperature ˚C/PV and ˚C/SV, humidity %/PV and %/SV display and setting, Temperature range: -20˚C~100˚C, Humidity range: 20%RH~98%RH, Constancy: ±0.3˚C ±2.5%RH, Uniformity: ±1˚C ±3%RH, Temperature and humidity sensor: PT 100Ω, Temperature and humidity audio and visual warning and OFFS correction setting, Temperature heater: 1.5KW X 2pcs, Humidity heater: 2.5KW X 1pc, Heat up transition time: -20˚C~100˚C within 35 min, Refrigeration system: Air cooled, single stage, Cooling compressor: Bristol hermetic compressor, Cooling capacity: 1,892 Watts, 6,455 BTU/hr, 1,630 Kcal/hr, Cool down transition time: 20˚C~-20˚C within 45 min, Safety devices: No fuse breaker, refrigerator over load relay, refrigeration high pressure switch, over temperature protector, protection relay, protection fuse, water level control and overheat protector, Chamber: L50 X W60 X H75cm, Capacity: 225L, chamber with key lock, with lamp (DC 12V 50W) X 1pcs and double glass viewing window, testing cable port with cover: Ø25mm, 4 castors, W/S: shelf X 2pcs, standard testing wet cloth X 5pcs, PCV water container X 1pc
-
Product
Battery Monitoring System
BMS-3923
-
Kongter Test & Measurement Co., Limited
This battery monitoring system is an innovative solution to measure battery condition with communication way of Power Line Carrier (PLC). With multi-frequency measurement, users can monitor and analyze battery in all aspects: internal resistance, voltage, current, capacitance, temperature and so on.Based on our years experience for battery management system, we build very mature mathematical model that precisely predicts battery capacity. This will in another hand reduce the time that we spend on capacity measurement using a battery load bank.
-
Product
Servo-Pneumatic Asphalt Testing System
-
All signal conditioning, as well as high-speed data acquisition and control functions are done by the unit and graphically interfaced through CATS, windows based software running on a standard PC. The system is capable of performing the full spectrum of HMA tests: dynamic complex modulus, flow number, flow time, indirect tension, beam flexural fatigue and resilient modulus. These tests are done with the appropriate testing modules. The different testing modules can be obtained after the initial system acquisition at the same discounted price. In addition, guarantees system upgrades in order to meet future standards .
-
Product
Cable Locator
CL 20
-
Cable fault location with the BAUR CL 20. The CL 20 cable locator comprising a transmitter and a receiver is used to determine the exact location of cables and metal pipes. The ability to determine laying depths of up to 4.5 m and to measure signal currents at the touch of a button allows you to obtain reliable information on the position of the cable within the shortest time.* Fast and exact location of position and laying depth of cables* Intuitive operation – no special measurement knowledge required* Lightweight and manageable
-
Product
DL-ISO 10 Vpp MMCX Tip
DL-ISO-10V-TIP
-
- Ideal for GaN and SiC devices- Highest system accuracy- Fastest rise time- High CMRR - 160 dB
-
Product
Contact Time Extender
CTX
-
The CTX relays supply a 1.5 to 2.5 seconds of a contact output time extension for a momentary contact input. The CTX allows slower device such as scada systems and annunciators to operate thus preventing data loss on the action of protective relays/devices or trip indicators such as the E-Max Trip indication Relay (TIR).
-
Product
USB-6363, 32 AI (16-Bit, 2 MS/s), 4 AO (2.86 MS/s), 48 DIO USB Multifunction I/O Device
781443-01
Multifunction I/O
32 AI (16-Bit, 2 MS/s), 4 AO (2.86 MS/s), 48 DIO USB Multifunction I/O Device - The USB‑6363 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB‑6363 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Static Pressure Manometer Kit
EM201SPKIT
-
UEi Test & Measurement Instruments
A digital, time saving electronic manometer static pressure kit
-
Product
Memory Test Systems
-
ICs that record and retain data are called memory devices. Our memory test systems are optimized for volume production of memory semiconductors, a market where low-mix high-volume production is the norm, and feature industry-best parallelism (the ability to test a large number of semiconductors at the same time).
-
Product
FieldFox Handheld Microwave Spectrum Analyzer, 14 GHz
N9936A
Spectrum Analyzer
100 kHz to 14 GHz frequency range Expand capabilities with optional tracking generator, interference analyzer, built-in power meter, and more Make accurate spectrum analyzer measurements ( 0.5 dB) without needing warm-up Locate interfering signals using the intuitive spectrogram display and recording capability Easily measure average and pulse power with a USB power sensor, pulse measurements with time gating Lightest microwave handheld spectrum analyzer at only 6.6 lb. (3.0 kg)
-
Product
PXIe-8830MC, Intel Core i7 Processor PXI MultiComputing Processing Module
783564-33
Processing Module
The PXIe‑8830mc allows two or more intelligent systems to exchange data using PCI Express technology. Featuring an Intel quad-core processor, the NI PXIe‑8830mc can be installed in any PXI Express peripheral slot. It runs on the LabVIEW Real‑Time OS and can act as a coprocessor to offload the processing from the main embedded controller in the system.
-
Product
Coil Analyzers & Power Supplies
-
Coil analyzers and power supply units are portable and lightweight devices intended for use in harsh switchyard and industrial environments. The typical application is switchgear and circuit breaker testing when substation battery is not connected or available. An advantage over substation battery is enabled testing in under-voltage and over-voltage conditions. Furthermore, the stable voltage outputs with a very low ripple (<0,5%) enable an analysis of the coil and motor current graphs recorded with circuit breaker analyzers from different vendors.SAT40AD, POB30AD, and POB40AD are unique devices in the market due to their dual purpose:Power supply for coils and spring-charging motorsTesting circuit breaker’s coils, motor, and auxiliary circuitAll DV Power coil analyzers and power supply units have four separate outputs for opening and closing coils.SAT40AD has two powerful motor outputs (AC and DC) which can withstand up to 40 A inrush current.POB30AD and POB40AD have DC motor output rated up to 30 A and 40 A respectively. With the use of motor outputs, POB and SAT can also be used as a power source or a temporary battery charger.SAT40A II series instruments can be controlled via PC. The DV-Win application software is used to control both SAT and CAT (Circuit Breaker Analyzers & Timers) devices at the same time, making a unique test system for switchgear and circuit breaker testing.
-
Product
Datapaq® Furnace Tracker Systems
-
For metal heat treatment industries, measuring both product temperature and its environment is critical to ensure both product quality and process efficiency, which is why Fluke Process Instruments has designed the most robust, sophisticated furnace profiling systems. From data loggers and thermal barriers to intuitive software data analysis and reporting, we have everything users need to profile their process, no matter how challenging. The Datapaq Furnace Tracker System is designed to be used repeatedly, in-process in the most hostile manufacturing environments, while still providing accurate and reliable through-process temperature surveys. Each system can help users improve performance and system accuracy, decrease downtime, reduce TUS reporting times and more.
-
Product
STRUCTURED LIGHT PROJECTORS
LUMAXIS
-
Lumaxis strives to become an industry leading supplier of state-of-the-art-projection engines for 3D Metrology. Our mission is to accelerate the industry’s transition to the most advanced and economically compelling structured light projectors available. Please take a moment to tell us your requirements in the form below. We understand this is a very price-sensitive industry. Our ability to deliver projection engines at an aggressive price depends largely on quantity and the capability of the projector you’re requesting. Thank you for taking time to provide this information.
-
Product
PXIe 8 Bit High Speed Digitizer - 1.25 GS/s on 4 Channels, 500 MHz Bandwidth
M4X.2212-X4
Digitizer
The 9 models of the M4x.22xx-x4 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
Pulse Pattern Generator, 3.35 GHz, dual-channel
81134A
Pulse Generator
When timing and performance requirements are critical, for example in high-speed serial bus applications like PCI Express or Serial ATA, its fast rise times and low intrinsic jitter allow the precise and in-depth characterization of devices, e.g. receivers or backplanes. On top of that, it allows to generate application-specific signal levels like pre- and de-emphasis (PCI Express) or squelch (Serial ATA). The Keysight 81134A lets you test your DUT instead of the pulse or data source!
-
Product
Test Head Manipulators
Cobal 250
-
The Cobal 250 offers the best-in-class range of motion for universal manipulators with seven degrees of motion. Separate linear movements make it easier for the operator to dock, undock, and redock the test head in seconds. In combination with inTEST EMS docking, the Cobal 250 is compatible with testers for both Wafer Sort and Final Test, minimizing the time and cost when moving a tester between Sort and Final Test.
-
Product
PXI Single RF Attenuator, 2.3GHz
41-181-021
Attenuator
The 41-181 Programmable Attenuator Module is available with either one or two independently programmable attenuators in a single width 3U PXI module. Each attenuator uses high reliability mechanical switches to operate binary weight attenuator pads, providing attenuation values from 0 to 63dB in 1dB steps. Attenuator operating time is typically just 5ms, ensuring fast setting times.
-
Product
Logic Analyzer Software
-
Logic analyzer application software allows you to gain quick insight into your digital system. These software applications provide a wide range of additional capabilities including shortening setup time and customizing measurement displays.
-
Product
Modular Mounts
M-SWITCH
-
The M-Switch series of adjustable, modular mounts are designed to redirect a horizontal interferometric set-up to a vertical one. This vertical orientation can help reduce distortion effects commonly found from clamping, and reduce alignment time. There are 4 primary versions of hardware designed to enable testing of mirrors, windows, lenses and lens assemblies. Holding of the part under test can be done with a variable 3 arm mount (for flexibility) or our kinematic mount (for high volume). Reference mirrors can be supplied with a variety of flatness and coating specifications to match your application needs.
-
Product
Automatic Oil Insulation Test Kit
-
The test kit is fully automatic and has the facility forAuto/Manual selections. The operator simply needs thesample in the test vessel & selects the required test. Testingcan be done as per many international ( IEC & Europeanstandards ) which are programmed into the instrumentmemory . Stand time, Stir times & Rate of rise of appliedvoltage can be selected in Custom Mode also , one setof such selected mode can also be stored in the memory. In addition to the above set can also perform withstand test(proof) tests. In this test the set allows the set voltage to pre-set value & hold for one minute to see if breakdown occurs. The backlit LCD is used for user friendly operationsduring the test process. It also display fault condition messages such as open ground and cover open . All the user selected programmes are chosen through(4x3) key pad.The test results can be printed along with with test type, date, time, breakdown test voltage, averages and deviations. Voltage value can be measured & printed with a resolution of 0.1kV. In reprint option it is possible to have number of printouts for the last test. For each test the readings are recorded and stored in memory.
-
Product
General Purpose Low-side MOSFET Drivers
-
Renesas' family of low-side FET drivers are very high-speed matched dual-drivers capable of delivering peak currents of 2.0 amps into highly capacitive loads and excellent at driving large capacitive loads with minimal delay and switching times. The high-speed performance is achieved by means of a proprietary "Turbo-Driver" circuit that speeds up input stages by tapping the wider voltage swing at the output. Improved speed and drive capability are enhanced by matched rise and fall delay times. These matched delays maintain the integrity of input-to-output pulse-widths to reduce timing errors and clock skew problems. This improved performance is accompanied by a 10 fold reduction in supply currents over bipolar drivers, yet without the delay time problems commonly associated with CMOS devices. Dynamic switching losses are minimized with non-overlapped drive techniques.
-
Product
Peak Power Analyzer
4500C
-
The Boonton Model 4500C is the instrument of choice for capturing, displaying, analyzing and characterizing microwave and RF power in both the time and statistical domains. It is ideal for design, verification, and troubleshooting of pulsed and noise-like signals used in commercial and military radar, electronic warfare (EW), wireless communications (e.g., LTE, LTE-A, and 5G), and consumer electronics (WLAN), as well as education and research applications.
-
Product
Saluki S2106 Series OTDR (up to 45dB)
-
Saluki S2106 Series Optical Time Domain Reflectometer is a high performance multi-function test instrument designed for the FTTx network. The product has a range resolution of up to 0.05m and a ultra-short event blind zone of 0.8m. This product integrates OTDR, LS, OPM, VFL, Event Map (iONM), OLT and OFD function all in one. It adopts touch and button dual operation mode. The product has rich external interface, which can realize remote control through Ethernet interface or two different USB interface for external USB flash drive, printer and data communication with PC.
-
Product
Automation Testing Services
-
QACraft has been one of the leading companies in providing automated testing services for all types of software and applications inclusive of mobile as well as web apps. Our expert team designs the QA strategy to check the various parameters such as functionality, speed, performance, quality, loading time, and much more to give you a detailed report about the same.
-
Product
4-port LAN Module With Intel® I350-AM4/I211-AT Ethernet Controller
AX93336
-
The AX93336 LAN module is built with an Intel® I350-AM4/I211-AT GbE Ethernet controller, incorporating Jumbo Frames and Intel® VT-c (Intel® I350-AM4) to optimize network traffic processing. It also comes with an optional LAN bypass function to ensure smooth network connectivity at all times, making it an ideal solution for users seeking better protection of their essential business communications in the event of a power outage, system shutdown or crash. This LAN module’s high-density design is specifically adapted for Axiomtek’s 1U and 2U rackmount network appliances, featuring four 1 GbE RJ-45 or four SFP ports plus a PCIe 2.0 x8 golden finger for expansion flexibility, giving customers the freedom to streamline their individual network infrastructure deployments to fulfill fast-changing networking demands quickly and cost-effectively.
-
Product
Portable Pinhole Detector
DZK-18
-
Shanghai Dean Electrical Co., Ltd
Online testing mode: round wireΦ0.05 -Φ5.0, flat wire B side Φ 3 - Φ 18Hand detection mode: round line diameter is not required, flat line width is not requiredTest length: 0-999 m to infinity (set by user)Detection speed: set by the userDefect short circuit current: 25±5uAResponse time: 5 ±1msWorking environment:0-40℃Relative humidity: 75% or lessOperating voltage: AC220V±5%Power consumption: <20W
-
Product
LXI WTB Terminator, 100 ohm
60-983-001
Terminator
The 60-983 is an LXI compatible Wired Trigger Bus Terminator (WTB) designed to be attached to the end of a WTB cable. The LXI WTB uses a transmission line cable to connect LXI devices together that support the WTB capability of the LXI standard. Like all transmissions it needs to be correctly terminated to avoid reflections that could change the signal amplitude along the cable and generate timing jitter or trigger errors. The 60-983 is a simple terminator that can be placed at each end of the WTB chain to correctly terminate the transmission line with minimal reflections.
-
Product
In-Circuit Test (ICT)
-
Analog components (resistance, capacitance, inductance, diodes, transistors, etc.) as well as complex digital components can be tested in the ICT. Compared to other test methods (e.g. flying probe), the in-circuit test enables very short test times (= high assembly throughput) combined with a very high test coverage.
