Filter Results By:
Products
Applications
Manufacturers
Optical Transmission
-
product
DDLS 200 with 2 Mbit/s Transmission Rate
Leuze electronic GmbH + Co. KG
Optical data transmission for RS interfaces and fieldbuses up to 300 m and up to 2 Mbit/s. Infrared data transmission protects the DDLS 200 from interference. Systems are available for all common industrial fieldbus interfaces. The ranges are stepped and reach a maximum transmission distance of 300 m. Low ambient light sensitivity through special FSK method. Available interfaces: PROFIBUS, Interbus and CAN/DeviceNet, as well as RS422 and RS 485.
-
product
Optical Signal Transmission
Analog
Used for oscillographing analog signals under EFT/EDS/RF interference.
-
product
Optical signal transmission
Bus systems
Allows for the transmission of high speed CAN signals via optical fibre cables during EMC tests or when there are great potential differences (high voltage).
-
product
Optical Fiber Converters
Optical Fiber Transmission products play an important role in systems for wide-band analog signals and digital signals with high data rates. They send and receive data from point-to-point via a network, thus the fundamental function of all fiber systems from small to large. A lot of optical fiber transmission products are available from Fiberinthebox, such as Optical Fiber Transceivers, Fiber Media & Protocol Converters, Optical Multiplexers, Fiber optic modems, Optical Switches, Network Interface Cards, and PON & AON. Our optical fiber transmission products are developed and manufactured to provide reliable, durable performance.
-
product
Optical signal transmission
Digital
The fibre optic cable are used to transmit digital signals from the device under test under EFT/burst interference.
-
product
Fiber Adapter
USB Serial Optical Converter
*Optical data transmission*Glass fiber or POF*Optimal galvanic isolation*USB bus-powered*Virtual serial interface*Baud rate up to 115kBit / s
-
product
Optical Components & Transmission Simulation Software
VPIphotonics Design Suite
VPIphotonics Design Suite™ embeds expert knowledge from our component and transmission design tools in one shared, flexible software environment to support requirements in design, analysis and optimization providing you with the most powerful numerical algorithms tailored for your applications.
-
product
Fiber Adapter
I2C fiber adapter
*Optical data transmission*Glass fiber or POF*Optimal galvanic isolation*Up to 350kHz*Up to 50m*No software or drivers required
-
product
Optical Switches
Fast and reliable optical switches to streamline your test procedures. Can be customized with a wide range of switch configurations, fiber types and connectors.
-
product
PXIe, 1-Channel, SMF28 Fiber, 1x4 PXI Optical Switch
786598-01
PXIe, 1-Channel, SMF28 Fiber, 1x4 PXI Optical Switch - The CohSol SwitchPXIe-1003-1 is a PXI Express, 1x4 multiplexing switching module that supports optical switching at wavelengths from 1,260 nm to 1,630 nm using single-mode fiber. The switch provides either SC/PC, FC/PC, SC/APC, … or FC/APC fiber-optic connectors. You can use the CohSol SwitchPXIe-1003-1 for repeatable, low-loss switching.
-
product
Automated Optical Switch - MATRIQ
Add optical switching capability to your test system with Quantifi Photonics’ automated optical switches. The fast and reliable optical switch will enable automated sequential testing, saving time and streamlining your test procedures.
-
product
Broadband Optical Source - PXI
SLED 1000 Series
The SLED 1000 Series is a super-luminescent LED light source with high output power, large bandwidth and low spectral ripple. It comes in various wavelength models to address applications in the telecom and datacom markets.The SLED is a single-slot PXIe module and is ideal for building a customized optical testing platform that delivers reliable and repeatable results in manufacturing or R&D environments.
-
product
Optical-Electrical Converter - PXI
O2E 1000 – 1400 Series
The O2E is a high bandwidth, broadband optical to electrical converter.Available in a range of configurations; choose from 1 or 2 channels, AC or DC coupling and various conversion gain and operating wavelength ranges.
-
product
PXI Optical Switch
The PXI Optical Switch is available in many different switching configurations for customized optical switching. It offers both single-mode and multimode fiber options that can support switching of very small wavelength signals. The switch provides either SC/PC, FC/PC, SC/APC, or FC/APC fiber-optic connectors. You can use the PXI Optical Switch for repeatable, low-loss switching.
-
product
Automated Optical Switch - PXI
Add optical switching capability to your test system with Quantifi Photonics’ automated optical switches. The fast and reliable optical switch will enable automated sequential testing, saving time and streamlining your test procedures.
-
product
Optical-Electrical Converter - MATRIQ
The O2E is a high bandwidth, broadband optical to electrical converter.Available in a range of configurations; choose from 1 or 2 channels, AC or DC coupling and various conversion gain and operating wavelength ranges.
-
product
Broadband Optical Source - MATRIQ
Our SLED MATRIQ instrument is a compact super-luminescent LED light source with high output power, large bandwidth and low spectral ripple.The SLED comes in various wavelength models to address various key applications across telecom and datacom, and is ideal for building a customized optical testing platform that delivers reliable and repeatable results.
-
product
Data Transmission
HighReach Measuring & Controlling System Co.,Ltd
Is sending and receiving digital or analog data between devices.
-
product
Fiber-Optic Transmission
Fiber optic transmission systems all use data links that work similar to the diagram shown above. Each fiber link consists of a transmitter on one end of a fiber and a receiver on the other end. Most systems operate by transmitting in one direction on one fiber and in the reverse direction on another fiber for full duplex operation. It's possible to transmit both directions on one fiber but it requires couplers to do so and fiber is less expensive than couplers. A FTTH passive optical network (PON) is one of the only systems using bidirectional transmission over a single fiber because its network architecture is based around couplers already.
-
product
Transmission Operations
Schweitzer Engineering Laboratories, Inc.
The safe and efficient operation of transmission facilities requires that critical information be sent to SCADA and system operators. With this knowledge, they can respond quickly and appropriately to power system events.
-
product
Transmission Line/Cable Testing
HAOMAI Electric Test Equipment Co., Ltd.
Transmission Line/Cable Testing products by Haomai
-
product
Telecom Transmission Tests
Networked Communication Solutions, LLC
Is designed to test across the full bands of T1-Lite® or E1-Lite® or test individual timeslots.
-
-
product
Transmission Line Pulse Testing
Transmission Line Pulse testing, or TLP testing, is a method for semiconductor characterization of Electrostatic Discharge (ESD) protection structures. In the Transmission Line Pulse test, high current pulses are applied to the pin under test (PUT) at successively higher levels through a coaxial cable of specified length. The applied pulses are of a current amplitude and duration representative of the Human Body Model (HBM) event (or a Charged Device Model – CDM – event in the case of Very Fast TLP, or VF-TLP).
-
product
Transmission & Synchronization Tester
xGenius
xGenius is a nice handheld tester equipped with a large (8 inc) capacitive touch-screen to make easier the analysis and results interpretation. It is 100% suitable for labs or field use because is full equipped (IP/Ethernet/PTP/T1/E1), battery operated, light (1.9kg) and very rugged. The unit is able to test Ethernet/IP networks up to 10Gb/s while supporting master/slave Sync-E/PTP emulation and also has interfaces for T1/E1.
-
product
Network Transmission Tester
SIGNALTEK NT
If you install, maintain or troubleshoot data cabling and Ethernet networks, SignalTEK NT allows you to prove the performance up to Gigabit Ethernet transmission rates.
-
product
E1/Datacom Transmission Analyzer
DTA-BERT
DTA-BERT E1/Datacom Transmission Analyzer can perform E1 transmission performance test (BERT) and status monitoring on data link (V.35, V.24/RS232, RS449, RS530, X.21). Model T can also perform G.703-64K bit error test, PCM31/30 test and Jitter test. Featuring comprehensive functions, easy operation and compact design, DTA-BERT provides total solutions for E1 line analysis and maintenance.
-
product
Transmissive Rotary Disk
DISK-2
US Digital offers a wide variety of standard rotary encoder disks. They may be ordered as a stand alone disk (see below) or as a codewheel (see the Disks page). These rotary encoder disks are made from mylar polyester film. This material allows for a wide temperature range and is virtually unbreakable. There is no minimum order.
-
-
product
High-end Transmission Electron Microscope
CryoARM
JEOL announces the latest member in its family of high-end transmission electron microscopes, the CryoARM. This highly automated TEM is designed for unattended operation and high throughput imaging of cryo-EM specimens. The CryoARM was initially introduced to a select audience at the 2016 Gordon Research Conference in Hong Kong, M&M 2016 in Columbus, OH and EMC 2016 in Lyon, France. The CryoARM is a dedicated cryo-TEM, based on the highly successful JEOL ARM (Atomic Resolution Microscope) series, an ultrahigh performance, highly stable platform considered to be the "best-in-class" TEMs. The development of the CryoARM was accomplished in collaboration with leading Life Science researchers.
