Voltage Interruption
-
Product
Synchronous GPS Based I/O Controller & Interrupter
interX
-
interX was originally developed as a measurement instrument for industrial and trunk pipeline anodic or cathodic protection systems. interX allows facilitate measurement of galvanic parameters (instant-off polarized potentials, pipe-to-soil potential) across a wide range of timing cycles. It is used to make synchronous disconnect and reconnect of protection electrodes (anode or cathode) or rectifier's from/to buried underground pipeline to perform measurements.
-
Product
Voltage Detector
LV-1
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
Using conductive rubber tip, free from short circuit. With slip stopper for the safety use.
-
Product
VLF Voltage Generators
-
Fivestar HV Testing Equipment Co., Ltd.
VLF hipot is an AC output tester with an output frequency of 0.1 Hz or lower rather than 50/60 Hz. Although the frequency is very low, it is an alternating current with polarity reversals every half cycle.
-
Product
DC Voltage Generator
MON8P
-
Mezzanine MON8P is designed to generate DC voltage in the range of ± 10 V through eight galvanically isolated channels from each other and from the case, which allows to reduce the level of interference and increase the safety of the device.
-
Product
Current, Voltage, Resistance
-
Solutions for the testing and calibration of current, voltage and resistance are used in industry (laboratories, production, workshops), in calibration service companies and in quality assurance. These instruments are portable and mobile and are particularly notable for their low measurement uncertainty and high scope of operation.
-
Product
Low Voltage Regulation
-
The low voltage regulation system LVRSys represents a cost effective alternative for grid expansion. The economic use is recommended in all low voltage grids where short-circuit power is sufficient, but have voltage maintenance problems.
-
Product
High Voltage Amplifier
WMA-100A
-
The WMA-100A model is our cost-effective, compact, general purpose high voltage amplifier. With its high quality and small form factor, it is the ideal choice for any experiment that requires an all-round, reliable high voltage amplifier. It can also be used as a stand-alone low noise high voltage power supply. Two WMA-100A amplifiers and a WMA-IB-HS phase inverter - buffer can be used to double the output voltage.
-
Product
Compliance Voltage Ohmmeter
ΩhmRanger-LCV
-
ΩhmRanger-LCV is an accurate, 3.5 Digit, Low Compliance Voltage Ohmmeter. It is able to measure from >100M to 10 Ohms, ΩhmRanger-LCV is suitable for professionals and enthusiasts alike.
-
Product
Personal Voltage Detectors
-
*Provides another level of safety for line crews, storm restoration workers and first responders*Alerts user to the proximity of electric fields or energized electrical equipment with a loud alarm and bright lights*Frequency of alarm increases as the user gets closer to the electrical hazard*Detects voltage above line-to-line*Typical initial warning distance is about 7 ft from a conductor*Warning distance increases with higher voltages*Field replaceable 9V battery with low battery indicator
-
Product
8-Ch Relay And 8-Ch Isolated Digital Input W/ Digital Filter And Interrupt PCIe Card
PCIE-1761H
-
8 opto-isolated digital input channels8 relay actuator output channelsInterrupt handling capability for all DI channelsSelectable Digital filter time for all DI channelsOutput status readableLED indicator to show activated relaysSelectable Form A or Form C
-
Product
Battery Voltage Supervisor
BVS
-
DV Power battery voltage supervisor – BVS, is an accurate battery voltage monitoring system that monitors the state of health of battery systems. It records important battery parameters such as battery voltage, inter-cell connection voltage, and ambient temperature. Because of that, it can be a support tool for capacity testing.The BVS voltage supervisor is an integrated system consisting of:BVS Control Unit (BVS-CU)Cell Voltage Modules (CVM)String Voltage Module (SVM) (optional)String Current Module (SCM) (optional)It is an ideal testing tool for maintenance, troubleshooting and performance tests on individual stationary batteries and battery packs in critical backup energy solutions.BVS-CU provides ambient temperature measurements on multiple locations (4 temperature channels). Overall string voltage and string current monitoring can be achieved by using an optional string voltage module (SVM) and string current module (SCM).There are two types of DV Power battery voltage supervisors:BVS – One cell voltage module measures 1 cellBVS-4 – One cell voltage module measures 4 cellsCVM modules detect cells that fail a discharge test based on monitored voltage values. As a result of that, these cells can be safely removed from the battery string.Data acquisition and analysis of data collected from the modules are available in the DV-B Win application software suite. They provide data viewing, tracking, and generation of comprehensive reports.
-
Product
Meters for Current & Voltage
EE301-DCM-xx
-
LCD Current Readings:0-80.0 / 40.0 / 20.0. LCD Voltage Readings:0-50.0 / 150.0
-
Product
Oscillators - Voltage Controlled
-
Teledyne RF & Microwave offers Voltage Controlled Oscillators (VCOs) utilizing bipolar transistors & silicon varactors over the frequency range of 40 MHz to 18GHz. Many of the VCO designs incorporate internal filtering, regulation & amplifiers to meet total system requirements in a small integrated package. Additionally, our hermetic hybrid designs can be screened to the most demanding military and space applications.
-
Product
Dielectric Withstanding Voltage Test
-
The dielectric withstanding voltage test (also called high-potential, over-potential voltage-breakdown, or dielectric-strength test) consists of the application of a voltage significantly higher than rated voltage for a specific time, between mutually insulated portions of a component part or between insulated portions and ground. This is used to prove that the component part can operate safely at its rated voltage and withstand momentary over-potentials due to switching, surges, and other similar phenomena.
-
Product
AC High Voltage Tester
VHT
-
VEER make High Voltage Tester VHT is specially designed to test Dielectric Strength of Device under Test as per applicable standards. High Voltage test is required to determine whether test object has proper insulation or not. High Voltage test is carried out as Routine Test Each device is subjected to test at high voltage of 1 kV + 2 x (working Voltage)If Insulation is weak then device will consume more power because of leakage current which causes more heat. Heat will reduce the reliability and overall life of device under test It is also responsible for high risk of electric shock. So, High voltage test is necessary for all electrical equipments.
-
Product
Voltage Testers
-
Electrical Receptacle Tester Instantly Displays Wiring Condition of Any Standard 3-Wire AC 110-120 OutletNeon Indicators Give Positive Indication of Current StatusCompact Unit Simply Plugs into any Standard 3 Wire/Grounded Receptacle (110–125 Volt AC Circuits)Tests for 6 Circuit Conditions: Open Ground, Open Neutral, Open Hot, Hot/Ground Reverse, Hot/Neutral Reverse & Correct WiringBlister PackedcULus ListedOrder Qty of 1 = 1 Piece
-
Product
Voltage Integrated Sources
VIS
-
The VIS voltage integrated source was designed to be used as a stable alternating voltage source for electricity meter test equipment, and in laboratories. The output voltage is isolated and independent of mains voltage. VIS is available in a variety of configurations depending on the values of output power and output voltage.
-
Product
High Voltage Ammeter
Ampstik®+
-
Use the Ampstik+ to safely take accurate current measurements when performing high voltage live-line load checks for balancing, switching, or breaking load. This high voltage ammeter measures in every electric utility setting with a linear current sensor to accurately measure .5A to 5000A, while in voltage environments up to 500kV. The opening of the amp sensor is electronically closed, while external currents are electronically rejected. This design enables the user to measure an individual conductor within close proximity to adjacent conductors without interference errors.
-
Product
High Voltage Differential Probes
-
A high voltage differential probe is used for measuring the voltage difference between two test points where neither test point is at ground. High voltage differential probes from Tektronix can be used for signals up to 6000 V. These probes are the best choice for making non-ground referenced, floating or isolated measurements in large part due to their common mode rejection capability. These products are designed, manufactured, and serviced by Tektronix.
-
Product
Voltage Meter
MN8IP
-
The mezzanine module (mezzanine) MN8IP is designed to measure instantaneous voltage values over eight differential channels isolated from each other and control circuits.
-
Product
Voltage Tester Pen
TOB-VT
-
Xiamen Tob New Energy Technology Co., Ltd
Non Contact Voltage Tester Pen For High Voltage Testing. Non-contact AC voltage tester pen has high precision and accuracy, with compact and portable design appearance, and the double plastic shell is to ensure the safety of the users.
-
-
Product
Non Contact Voltage Indicator
PL107N
-
Contact-free audible and visual indication of AC voltages between 90 and 1000 V AC Clear, omnidirectional flashing LED Quick and accurate detection of cable breaks Detects microwave leakage Phase detection in sockets Press to test switch avoids nuisance buzzing and extends battery life Supplied complete with 1.5 V AAA batteries
-
Product
Voltage Data Logger
VA601-V1
-
Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD
Multi-function record meter is a new record meter designed for the actual demand of various industrial site, which integr.
-
Product
Oil Breakdown Voltage Tester
DTA 100 C
-
Insulating oil testing with the BAUR DTA 100 C. The BAUR DTA 100 C oil tester is designed for continuous operation in the laboratory and is characterised by the combination of extraordinary features. As a high-performance device with a test voltage up to 100 kV, with clear breakdown detection and absolutely reliable measurement results even across several measurement sequences, the BAUR DTA 100 C is the leading testing device for users in the electricity and other industries and in testing institutes.
-
Product
sbRIO-9201, Non-Enclosed, ±10 V, 500 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module
781114-01
Voltage Input Module
Non-Enclosed, ±10 V, 500 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module - The sbRIO‑9201 is an effective combination of channel count and speed at a low price for an economical multifunction system. In addition to the absolute protection from the isolation, the module features up to 100 V of overvoltage protection for errant signal connection or unexpected outputs to the individual channels. Non-enclosed modules are designed for OEM applications.
-
Product
Testing of Voltage Measuring Transformers
-
In this category you will find components for high-voltage testing as well as for testing electronic or conventional voltage measuring transformers.
-
-
Product
Low Voltage Products and Systems
-
ABB provides a full range of low voltage solutions to connect, protect, control and measure a wide range of electrical installations, enclosures, switchboards, electronics and electromechanical devices. The business improves the reliability and efficiency of its customers’ activities across all major industries including the residential sector.
-
Product
Voltage Indicator
-
Small installation devices for measuring both alternating and direct voltages.
