-
product
RF Power Meter
4240
The 4240 series of CW RF power meters provides the high speed measurement capability needed in a production environment, as well as the simplicity of operation required for bench top use.
-
product
RF Reference Sources
The 27 GHz 96270A and 4 GHz 96040A Low Phase Noise Reference Sources are designed specifically for RF calibration, featuring a calibration-oriented interface, precision signal level and attenuation, high signal purity and precision low distortion modulation. Both instruments simplify the process of RF calibration by reducing the amount of equipment and simplifying the calculations required.
-
product
RF & Microwave
Data Patterns has a strong RF and Microwave engineering capability, featuring a team of enthusiastic engineering talent, substantial investments in RF test and measuring instruments, and attitude to utilise the latest technologies.An in-house manufacturing capability and an insatiable demand for fulfilling requirements of Radar, Electronic Warfare and Communication domains, Data Patterns has developed a whole line of building blocks including TR Modules, Up and Down Converters, Power Amplifiers, Transmitters, Combiners and Dividers for specific requirements. A list of products is given below.
-
product
- Optical / RF Converter
OPT 80
Calibrated measurement of the optical power of satellite and terrestrial TV signals distributed in optical fiber Calculation of optical signal losses on distribution Measurement of digital parameters (BER - MER - NM etc.) of optical signals converted into RF Visualization of optical carriers in RF Field Metric Spectrum Analyzer Power Meter Optical Field Meter Display Optical RF Power Supply Line Link Meter (LNB power supply ) Optical LNB power supply 13V 500mA with short circuit and overload managementAcquisition of optical measurements using the field meter Data Logger Option: certification of the OPT80 calibration and optical power measurements
-
product
Fixed Aperture RF Current Monitoring Probe
TBCP1-200
The TBCP1-200 is a fixed aperture RF current monitoring probe.The probe has a 3dB bandwidth of approximately 200 MHz. The aperture of the RF current monitoring probe is 25 mm. Its transfer impedance is > 14 dB Ohm in the range from 40 kHz to 200 MHz.
-
product
RF Milliwatt Meters
Type NDB-2 and NDB-3
National RF’s Type NDB-2 and NDB-3 RF Milliwatt Meters are affordable pieces of test equipment for both the RF laboratory and the home experimenter. Both provide a digital reading of RF power in dB reference 1 milliwatt of power into a 50 ohm load (i.e. 0 dBm). The circuitry consists of a low noise logarithmic amplifier that drives a digital A/D converting meter circuit. The lowest power levels that can be read are about –73 dBm (approximately 40 microvolts or .00000003 milliwatts). The maximum power input should not exceed 10 milliwatts (+10 dBm or .010 watts) when inputed without attenuation. An internal attenuator is provided and described in the next section.
-
product
RF & Microwave Power Meters
Our RF & microwave power sensors ensure precise and reliable measurements. They provide the highest measurement accuracy and speed, simple operation, technological leadership in thermal, diode and OTA core measurement elements as well as traceability to national standards.
-
-
product
RF Conducted Immunity Test System
RFCI61000-4-6
RFCI61000-4-6 RF Conducted Immunity Test System is an automatic test system which is for the conduction sensitivity testing, it is fully meets IEC61000-4-6.2006, ISO11452-4, GB/T17626.6-2008 and GTB152B-CS114 etc standards. RFCI61000-4-6 internal source and broadband power amplifier can be generated 3 voltage test levels: 1v, 3v and 10v, and has the function of the real detect output level. It has two operation software which is calibration software and test software. When measuring, the signal is in 1 KHZ sine wave amplitude modulation system (80%) to simulate the actual harassment, and can through the coupling/decoupling network (CDN or electromagnetic clamp) to make the harassment signal coupled to the device.
-
product
RF Downconverters
Today’s high-band signal standards are using higher frequencies and wider bandwidths than ever before for applications such as next generation 5G wireless services, satellite communications, electronic warfare, and more.
-
product
RF Detectors
BroadWave designs and manufactures RF Detectors and other coaxial RF components that are ideally suited for test, verification and system integration. With frequency ranges of DC to 18 GHz, our components offer consistent performance at a low cost with an emphasis on performance and configuration flexibility.
-
product
RF High Frequency Probes
*Low impedance*High bandwidth up to 20 GHz*Repeatable measurements*Coaxial design*Interchangeable center conductor
-
product
RF Power Splitter, Combiner, Divider
PD2360
INSTOCK Wireless Components, Inc
Wideband Frequency (350 - 1000 MHz)Low Insertion Loss (0.4 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.2 : 1 avg)RoHS Compliant Splitter ConstructionTri Alloy Type N Female (Jack) Low PIM
-
product
Bluetooth RF Test System
FRVS
FRVS is recognized by the Bluetooth SIG as a validated test system for qualification testing of products to Bluetooth BR/EDR and low energy RF test specifications.
-
product
RF & Microwave Broadband Amplifiers
SHF Communication Technologies AG
SHF has been active in the design and production of broadband RF-microwave amplifier. The outstanding performance makes our amplifiers suitable for a wide variety of applications in R&D. This includes not only optical communications, but also satellite communications, high-speed pulse experiments, data transmission, quantum communication, radar and antenna measurements.
-
product
RF & Microwave Passive Components
SHF Communication Technologies AG
SHF’s microwave components are broadband devices suitable up to 110 GHz. Our SHF BIAS TEES are well known but perhaps a slight variation does suit your application even better. DIPLEXERS are bias tees with a certain bandwidth in the low frequency path to combine or separate high frequency and low frequency signals into or out of a single line. DC-FEEDERS are bias tees without the capacitor. Therefore, it provides slightly lower insertion loss in case it is connected to an AC-coupled device which already has a capacitor on its input. Based on our air line construction, these passive components provide resonance-free transmission over the entire operating range.
-
product
LXI 75Ω RF Matrix - 1GHz
The design is fully scalable, allowing a variety of matrix sizes to be offered in a single family. It maintains a close path loss match for all routes through the matrix, minimizing the calibration effort that has to be invested by users in optimizing their test system performance. The design is non-blocking Y to X (or X to Y) allowing any input to be connected to any output. The construction is based on high quality electromechanical relays which provide a fast operating time compared to microwave relays.
-
product
PXI 12x8 RF Matrix 250MHz 75 SMB
40-726A-751
The 40-726A is a 12x8 RF Matrix Module suitable for switching frequencies up to 300MHz (50Ω version). The 40-726A is available in either 50Ω or 75Ω versions with a choice of coaxial connectors. The module is designed to provide a simple and scalable bidirectional matrix for RF frequencies. Isolation Switches are located on all coaxial connectors, these disconnect the matrix from the external test fixture. This maximizes isolation and RF performance.
-
product
IF/RF Receivers
IF and RF Receivers are designed for communications infrastructure applications. Wide input bandwidth and high sample rates allow digitizing close to the antenna. Various receiver architectures, such as zero-IF, IF sampling to direct RF receivers, are supported and available on chip post digital signal processing can be used to offset demands in the FPGA or digital ASIC and ease analog filtering.
-
product
RF Spectrum Power Meter
SPM-50
SPM-50A Spectrum Power Meter brings innovative testing concept and approach for RF cable system installation and maintenance. It combines the key function of spectrum analyzer and power meter, designed to measure the power characteristics of particular signal among mixed signals transmitted on cable, fast and accurately present result in power histogram or spectrum chart.
-
product
W-CDMA/HSPA+ Analysis Using NI PXI RF Test Instruments
RFmx W-CDMA/HSPA+
The NI-RFmx W-CDMA personality is a highly optimized API for performing physical layer measurements on W-CDMA cellular standard signals. NI-RFmx W-CDMA is completely interoperable with all NI-RFmx APIs. It provides simple access to the most advanced optimization techniques such as multi-measurement parallelism and multi-DUT measurements. The result is extremely fast and high-quality measurements with minimal software development efforts.
-
product
PXI Single RF Attenuator, 2.3GHz
41-181-021
The 41-181 Programmable Attenuator Module is available with either one or two independently programmable attenuators in a single width 3U PXI module. Each attenuator uses high reliability mechanical switches to operate binary weight attenuator pads, providing attenuation values from 0 to 63dB in 1dB steps. Attenuator operating time is typically just 5ms, ensuring fast setting times.
-
product
RF Detectors for Millimeter Wave
RF Detectors are essential microwave/millimeter wave products for most Tx (transmit sources). Transmitter output power measurement is the main application. It is essential to know the RF output power because the output power level must not go above values set by FCC regulations.The unit of power is the watt for RF detectors. But, most commonly used in most RF and wireless systems to express power is the terms of dBm or decibels related to 1 mW:View more RF Detector
-
product
RF Down-Converter
CDCM100A-2
Systems Engineering & Management Company
The CDCM100A Series Down-Converter is an IP-67 rated device designed for installation on antenna pedestals. It is a pressurized, water-proof module designed for use with antennas that have a Tri-Band Feed. The CDCMA100 Series Down-Converter is a block down-converter supporting 1415-1585 MHz, 1650-1850 MHz, 2185-2485 MHz and 4400-5250 MHz, down-converting 4400-5250 MHz to 300-1150 MHz.
-
product
PXI Hex SPDT RF Switch, 8GHz 50Ω SMA, Terminated
40-880A-003
The 40-880A-003 is a hex SPDT 50Ω RF switch with 8GHz bandwidth. The 40-880A range of SPDT switches have automatic termination of unused signals and are available as a dual switch in a 1 slot PXI module, a quad switch in a two slot PXI module or hex and octal switches in three slot PXI modules
-
product
Custom Radio Frequency (RF) Receivers & Sources
FLO – Frequency Locked Oscillators, IFM – Instantaneous Frequency Measurement, DCU – Digital Control Units, ACU – Antenna Control Units, IDCU – Integrated DCUs, and Other Custom Products
-
product
PXIe-5651, 3.3 GHz RF Signal Generator
PXIe-5651 / 781216-01
PXIe, 3.3 GHz, PXI RF Analog Signal Generator—The PXIe‑5651 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXIe‑5651 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
product
With CATV RF Input EDFA
HA4600/RF
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HA4600/RF series is the narrow-band multiplexing EDFA which suitable with CATV application. This EDFA build-in one unit 1550nm direct modulated CATV transmitter used in inter cutting local VAD service. Build-in WDM multiplexing TX optical signal and External input optical signal of the main road then enter EDFA amplification, to server the local users. In order to avoid TX output optical power and the external input optical power does not fit the main road interfere with each other, the output power of the TX through the build-in VOA, from front panel adjust and set. The whole unit is concision, install and debug convenient. Providing high-quality, low-cost solution for all-optical relay 1550nm optical CATV systems, second-grade service area or administration village inter cut local VAD service.
-
product
1203c Broadband RF Distribution
Precise Time and Frequency, Inc.
The ptf 1203C Broadband RF Distribution amplifier provides high performance frequency references for laboratory or system use.The ptf 1203C uses two stages of input signal buffering to distribute the input signal to 12 separate outputs, and insure maximum isolation between individual output signals.
-
product
Portable Monitoring Receiver and RF Recorder
IZT R3301
The IZT R3301 is a portable receiver with an integrated server for data recording. The receiver is optimized for recoding of RF signals in frequently changing environments. The RF characteristics of the IZT R3301 are identical to the IZT R3000 series. # HF-VUHF-SHF receiver# frequency 9kHz...3GHz (3...12GHz option)# continuous spectrum recording of 24 MHz bandwidth, IQ recording with 20 MHz
