BNC
-
product
Directional Couplers From 0.01 To 2000 MHz
Pulsar Microwave's low frequency directional couplers operate within the frequency range of 10 kHz to 2 GHz. They're available in either surface mount or connectorized designs. SMA female connectors are standard, but BNC, TNC, F, N, jack or plug are available upon request.Most of these directional couplers have a flatness of +/- 0.25 dB and directivity of 20 dB or better within the operating band. VSWR of 1.3:1 or better maintained on all ports for most models. Maximum power handling is between 1 and 3 watts depending on model.
-
product
Digital Quad-channel High-Frequency Lock-In Amplifier -
eLockIn 205
Being the top model eLockIn series, the eLockIn205/2 offers a very fast TCP/IP connection, ultra-fast DAC outputs of the measured signals and all signals supplied at BNC connectors.
-
product
BNC Male to BNC Male Cable, 75 Ohm, 2 m (Quantity 4)
779697-02
The BNC-BNC Coaxial Cable, sometimes referred to as BNC Plug to BNC Plug, connects measurement and signal devices.
-
product
PCB High Sensitivity, 100mV/g, ICP® (IEPE) Accelerometer
784170-01
The PCB HSTA15 helps you acquire sound and movement data with supported PXI Sound and Vibration Modules, C Series Sound and Vibration Input Modules, and USB-based Sound and Vibration Devices. This sensor uses the Integrated Electronics Piezo-Electric (IEPE) current excitation. The PCB HSTA15 features a sensitivity range of 10 mV/g and requires a 4-socket plug-to-3 BNC plug cable.
-
product
MCX Male to BNC Male Cable, 50 Ohm, 30 cm
188375-0R3
The MCX-BNC Coaxial Cable is used for modular instruments such as PXI switches. This cable is available in 1 m and 30 cm lengths.
-
product
BNC (M) To Minigator Test Clips
2886
Converts BNC (female) cables / connectors to minigator test clips for test versatility.
-
product
Amplifier Module
LNAM-LPA
We offer an evaluation board and case for the LNAM-B and LNAM-FBX modules. This Laboratory PreAmplifier (LPA) solution is powered by a switch-mode power supply and gives access to the LNAM in- and outputs via BNC sockets.
-
product
Probes, Cables & Detectors
Probe has a mica window that has a thickness of 1.8 to 2.0 mg/cm2. This allows detection of alpha radiation as low as 3.0 MeV when in close proximity to the window. Beta radiation in excess of 35 keV and X-ray or gamma radiation greater than 6 keV can also be deteched. The detector is provided with a BNC connector. It can be used with most count rate and survey meters which accept Geiger Mueller (GM) detectors operating at 900V DC.
-
product
External Input Module
EIM-01
The EIM-01 external input module is used to safely isolate and input an external drive signal into the MAC-01, -02 or -03 AC Power Sources/Frequency Converters. The unit can accept various waveforms from laboratory or programmable oscillators or from a Titan MOS-01, -01A, -01B when used as a slave unit in multi-KVA systems. BNC input is completely isolated and floating with 1,500VAC breakdown and excellent common mode rejection. A recessed 8% gain adjustment control is also provided. The EIM-01 must be factory installed.
-
product
Cable Tester, Coax Cable Mapper 8 ID Finder with Toner
TCT-128
A handheld testing device designed for CATV and security installers to test multi-run coaxial cable systems terminated with "F" or BNC connectors. Uses eight color coded ID finders to locate and identify cables.
-
product
Cable Assembly, Receiver, TriPaddle, 48", 37-Pin Female D-Sub
540016010601
Cable Assembly PXI / VXI 6 BNC 48"
-
product
Time & Frequency System
TM-4M
The TM-4M Time & Frequency System features a larger, easier to use form-factor. It was designed for mobile applications that require uninterruptible power, and for applications that require multiple front panel connections. The six BNC jacks on the front panel are user-assignable to output any signal the user chooses.
-
product
R.F. Coupler and high Pass Filter
7415-3
There are those who disagree with the r.f. conducted susceptibility test setup of Method CS02 of MIL-STD-462. Homemade rigs have sprouted to comply with the coupling capacitor requirement, each with it own disadvantage. Our little Type 7415-3 R.F. Coupler is the answer. A neat little box with BNC connectors and a pair of binding posts, it is rated at 270 V.A.C. at the LINE terminals and 20 volts PMS into the GEN port. Looks good and does a fine job.
-
product
DC to 2 GHz Power Splitter with BNC connector
11667L
The Keysight 11667L is a 50 ohm two-resistor type power splitter with BNC connectors. It is used with the E5061B network analyzer for power distribution network applications, such as DC-DC converter output impedance measurements with shunt-thru method (100 Hz to 10 MHz). It provides excellent amplitude (<0.2 dB) and phase tracking (+/-3), ensures highly accurate power splitting and low SWR minimizes measurement uncertainty.
-
product
MFI Michelson Fiber Interferometer
OPTIPHASE , a leading supplier of ultra-high performance interferometric systems, offers Fiber Interferometers for use in precision test and measurement instrumentation as well as fiber sensing systems. These interferometers are driven by our own PZ1 Low-profile Fiber Stretcher with enhanced modulation, through a front panel BNC connector. Michelson and Mach-Zehnder interferometers are available in wavelengths from 1064 to 1550 nm. Each interferometer has a “zero meter” path mismatch which provides flexibility to change the delay length to match varying test applications. The standard length shipped is 50 meters. We also build custom interferometers.
-
product
Analog And Digital Sensor Measurement Data For CAN Applications.
K- AN8 KIT
This K-AN8 (8 analog + 4 digital input) kit contains everything needed to get the K-AN8 set up and tested on a work bench.To help with connecting sensors to the analog and digital ports the K-BoB enables easy connection with BNC connectors.Influx K-Cal is easily connected via the Kvaser LeafLight interface and Kvaser T-CANnector. (Using the Kvaser T-CANnector to power up the K-AN8 (at the desk) and terminate the CAN bus).
-
product
DAS / 4G LTE Power Dividers, Combiners
INSTOCK Wireless Components, Inc
INSTOCK Wireless offers wideband RF power divider / combiners optimized for DAS (Distributed Antenna System), 3G, and 4G LTE modem gateway splitting applications. INSTOCK cell-band and DAS splitters are commonly used for in-building wireless (IBW) network deployments. Available in 2-way thru 48-way configurations spanning 698-2700 MHz with exceptional performance. Type N, SMA, TNC, BNC, and QMA connector configurations INSTOCK.
-
product
DC Blocks
Coaxial DC Blocks allow the transmission of RF signals while blocking DC signals, usually using a blocking capacitor. We feature SMA DC blocks, 2.92mm DC Blocks, 1.85mm DC Blocks, BNC DC Blocks, TNC DC Blocks, and Type N DC Blocks. DC blocks can block the inner conductor, outer conductor, or both; hence there are "inner" dc blocks, "outer" dc blocks, and "inner/outer" dc blocks. These Coaxial DC Blocks are frequently used in Satellite Systems where a control voltage is passed along with the RF signal, and the coaxial dc block protects equipment. The BNC DC block uses a precision bnc to get to 4ghz. The C0927 SMA DC Block uses dual parallel capacitors to achieve its broad bandwidth, its ideal for EO & NRZ systems.
-
product
NI-9215, ±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
783739-01
±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The NI‑9215 performs differential analog input. The module contains NIST-traceable calibration, a channel‑to‑earth ground double isolation barrier for safety and noise immunity, and high common-mode voltage range. It is also offered in two connectivity variants: 10‑position screw terminal or BNC.
-
product
NI-9215, ±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
779011-01
±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The NI‑9215 performs differential analog input. The module contains NIST-traceable calibration, a channel‑to‑earth ground double isolation barrier for safety and noise immunity, and high common-mode voltage range. It is also offered in two connectivity variants: 10‑position screw terminal or BNC.
-
product
50 Ohm BNC to SMA Adaptor Assembly
40-978-511-2m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
UHF/RFID Power Divider Combiner 6-Way, BNC Female, 350-1000 MHz, 30 Watts
PD2561
INSTOCK Wireless Components, Inc
PD2561 is a RoHS compliant, 6 way, wideband, 50 ohm, RF power divider, power combiner furnished with BNC jack female coaxial connectors. All wireless band frequencies in the range from 350 to 1000 MHz are covered with optimal RF performance. Max microwave input power levels up to 40 watts can be handled in both power splitter and power combiner applications. See 6 way power divider input rating tables for additional details.
-
product
LXI High Frequency Matrices
Pickering's LXI high frequency (HF) matrix modules are suitable for switching frequencies up to 50MHz. They have an impedance of 50 and uses SMB signal connectors or with a larger case size is uses BNC connectors. This HF matrix is designed to provide a simple and scalable bidirectional matrix for radio frequencies and is intended for the easy construction of high performance bidirectional matrix switching systems.
-
product
Oscilloscope Probe Kit
6HP-9060
Switchable X1/X10/X100 attenuation with reference switch positions. Break-resistant center conductor & wide compensation range. Flatter response, sharper leading edges. Faster rise time and replaceable cable probe head tip and ground lead. Max. input voltage: 600V/1200V (DC-peak AC). Includes BNC adapter, IC tip, insulating tip & trimming tool.
-
-
product
Low & High Voltage Differential Probes
T3
Teledyne Test Tools Low & High Voltage Differential Probes offer end user versatility with all models powered by an external universal power supply and work with any Oscilloscope with a high-impedance BNC input. The range consists of one Low Voltage and three High Voltage models with varying bandwidths to satisfy a wide array of customer applications.
-
product
MCX To BNC-M Trig/Sync Cable (DG/TB/TD/TL To DSO); 50cm; RoHS
CBMCXBNCMNAA
CBMCXBNCMNAA: trigger/sync cable. Spec.: MCX plug-BNC-M50cm length. For interconnecting DataGenerator, TravelBus, TravelData, or TravelLogic series trigger out to any DSO BNC input For trigger/sync input from TL4x34
-
product
Picolo Pro 2
4x BNC connectors on the bracket32-bit 33 MHz PCI busOne video decoder, 25/30 images per second (50/60 fields per second)Fast switching between up to 4 camerasPCI and PCIe versions available
-
product
MOD MONITOR
TYPE HFX-1
The Type HFX-1 Modulation Monitor is an ancillary piece of equipment, which is used with narrow bandwidth, or older oscilloscopes to allow viewing of RF signals and particularly modulated signals as high as 55MHz. The equipment contains an RF signal source and a broadband mixing circuit which converts the high frequency signal to an intermediate frequency within the oscilloscope’s range. The frequency control dial is simply adjusted until the RF signal is viewed on the scope. BNC connectors are mounted on the rear panel to allow interconnect to the scope and RF probe. This product was previously called "oscilloscope frequency extender" and may be used to view other high frequency signals on older or narrow band scopes.
-
