Control
Known value
-
Product
Power Supply
-
Constantly calculates and adjusts the Voltage and Current limit points according to availablemaximum power (160W)At maximum current (10A), voltage is limited to 16V;at maximum voltage (42V), current is limited to 3.8ADual action rotary encoder control with push knob for fine and coarse tuning Remote control for Programming, Output Voltage/Current, and ON/OFF using supplied software, driver,and USBStore 20 presets with up to 999 cycles each on a PCvia USB and supplied SoftwareOutput Voltage: 0 to 42VOutput Current: 0 to 10ABasic Accuracy: (0.2%+5 counts)
-
Product
Battery Temperature Test Chamber
-
Sanwood Environmental Chambers Co ., Ltd.
Sanwood climatic chambers for battery can be tested under controlled temperature and humidity conditions, similar to the conditions under which batteries operate during their lifetime.
-
Product
Flowmeters
-
Parker high performance flowmeters provide a consistent line of accurate and efficient measurement solutions that can work with a wide range of industrial media. Choose from our many different types of flowmeter, each adaptable to meet the needs of your application. We also supply PFA and PTFE flowmeters for leak-free, precise control of ultra-high purity liquids and a diverse range of gas mass flowmeters. These enable us to meet demands for expanded flow ranges and high operating pressures, making them suitable for use in extreme environments.
-
Product
UV Test Chamber
-
Wewon Environmental Chambers Co, Ltd.
* UV test chamber simulates damaging effects of long term outdoor exposure of materials and coatings by exposing test samples to varying conditions of the most aggressive components of weathering – ultraviolet radiation, moisture and heat. * UV test chamber use fluorescent lamps to provide a radiation spectrum centered in the ultraviolet wavelengths. Moisture is provided by forced condensation, and temperature is controlled by heaters. Based on your testing sample’s size, We has two options uv test chambers for choice.
-
Product
SP4T RF Pin Diode Switches To 16 GHz
-
The 4-way series of absorptive and reflective switches operate from 100 MHz to 16 GHz. They are rated at 200 mW maximum input power and have a switching time of 100 ns. SP4T switches that operate up to 8 GHz have a maximum VSWR of 1.6:1 and minimum isolation of 60 dB. All absorptive and reflective switches manufactured by Pulsar Microwave require both positive and negative 5-volt supplies. Additionally, the TTL control logic operates from 0 to +5 VDC. Voltage connection is made with feed thru terminals. Ground connection is made through the chassis and turret terminals.
-
Product
Automated Breakthrough Analyzer
ABR
-
The ABR is a dedicated breakthrough analyzer with fully programmable operation including control of total pressure, flow rate, composition and temperature. Samples are loaded into interchangeable reactor beds and dried in-situ with purge gas or vacuum at elevated temperature. Reactive gas mixtures are then flowed through the bed, and the downstream composition determined in real-time with an integrated mass spectrometer.
-
Product
Renewable Energies
-
National Meter Industries Inc.
Is the evolution of dynamic power controllers designed to control hybridinstallations (powered by two alternative sources of energy). The unit measures theconsumption of the user at all times, thanks to its dual configuration, regulating theinverters to adapt the solar energy generation to the type of network and/or generatorinstalled.
-
Product
PWM Servo Amplifiers
-
Direct digital pulse width modulation (PWM) amplifiers — along with PMAC controllers — provide highly accurate positioning for industrial applications.
-
Product
LED/CCD Optical Micrometer
LS-7000 Series
-
Breakthrough technology intelligent optical micrometer with 0.01-micron high resolution, 2400 samples/second high speed. Maintenance - free LED emitter and design (no laser diode or motor). High performance controller with statistical analysis. Controller with target viewer available for easy setup
-
-
Product
Electronics Functional Test
Functional Test
Functional test for productive manufacturing. Manufacturers of products enabled by electronics must assure proper operation prior to shipment. Bloomy’s line of universal test systems are ideal for functional test of your PCBAs and subassemblies, from the simplest to the most complex. The UTS family of products combines high-performance test instruments, switching, power control and mass-interconnect hardware with our robust UTS software suite into a low-risk, cost-effective and powerful test solution for your device under test (DUT).
-
Product
Standoff Capacitors
-
In standoff capacitors, SemiGen offers controlled dielectric thicknesses of +/- 12 microns, < 0.1 micron mounting surface finishes, and outline (L&W) tolerances of < 25 microns. We assure lot-to-lot repeatability and very attractive pricing. RF engineers requiring jumper mounts, bypass and tuning capacitor flexibility will find our wide selection of standoff capacitors convenient and reliable.
-
Product
PXIe-2514, 7-Channel, 40 A PXI Signal Insertion Switch Module
780587-14
Signal Module
PXIe, 7-Channel, 40 A PXI Signal Insertion Switch Module—The PXIe‑2514 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXIe‑2514 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls (FADECs).
-
Product
PMC Dual Channel MIL1553B Board
MS 1722
-
- Bus Interface:- 32 Bit PCI Bus with PMC Interface- Speed of operation up to 66MHz- 553B controller based design- 2 dual redundant channels- Driver interface for Windows2000/XP/VISTA and LINUX OS- Self Test future
-
Product
Camera Link Simulator
CLS-221
-
The CLS-221 Camera Link Simulator is an affordable, high-performance video test pattern generator that supports all video formats including those introduced in the new version 2.1 specification. Fully programmable video timing enables the CLS-221 to mimic the characteristics of almost any camera. New features include enhanced timing performance, bayer color support, and additional video patterns. Control is via an RS-232 port, USB, or frame grabber COM port. The CLS-221 also incorporates the AIA validation test pattern.
-
Product
Indicating Differential Pressure Transmitter
605
-
The Series 605 Magnehelic Indicating Transmitter provides for both visual monitoring and electronic control of very low differential pressure.
-
Product
Harness Design and Manufacture
-
When designing an underwater cable harness, there are some factors which need to be considered, and we have produced the following list as a guide for customer information:Component considerations:- Electrical requirements- Mechanical considerations- Quality requirements- Reliability- Design redundancy (contact count)- Connector selection (type and form)- Locking requirements- Backpotting requirements- Waterblocking in moldings- Cable specification- Cable jacket material and compatibility with elastomers- Abrasion resistance- Stiffness profile at termination- Connector format (straight or right angle)- Molding format (straight or at an angle)- Clearance allowance for molding and cable routing- Elastomer compatibility (eg oil filled units)- Metalwork selection re: corrosion and cathodic delamination- Surface finish for metalwork as appropriateOperational considerations:- Operating depth profile (not just max. depth)- Tensile loads- Torsional loads- Bending loads- Bend control requirements (to limit bending at termination)- Deployment and recovery loads- Dynamic loading-Flow turbulence effects.
-
Product
Fixed Gas Detectors
OLCT 10 - OLC 10
-
Teledyne Gas & Flame Detection
The OLC 10 and OLCT 10 are designed to detect combustible or toxic gases for tertiary applications (boiler plants, battery charging rooms, car parks, hospitals). Two OLC 10's can be connected to one detection channel to monitor the same area, without an additional junction box or extra wiring. Similarly, up to five OLCT 10's can be connected to one channel for the detection of CO, NO or NO₂ in a car park application. Easy to install and operate, these detectors combined with the MX 16 control unit meet demanding user requirements.
-
Product
Multi-interface Electronic Control Unit
-
The Mors Smitt CatEnergy control unit ECU is the most modular and scalable solution available on the market for all function using high voltage measurement. From Energy Measurement purpose to all essential train function, the CatEnergy ECU is the perfect compact system for all demanding application on existing and new build train.
-
Product
PathWave IV Curve Measurement Software
PW9251A
-
The PW9251A PathWave IV Curve Measurement software helps to control Keysight SMUs for easy test setup and to perform IV measurements without any programming.
-
Product
Product Testing
-
E-Z-Hook can provide most client requested test reports for their purchased product. Some of our more common report requests include first article inspection, process control plans, product validation, RoHS, and tensile tests. In addition to product test reports, we can incorporate additional inspection criteria and lot number management if needed. Please contact us to discuss your custom test and inspection requirements.
-
Product
Circulators
-
Our Millimeter Wave Circulators are the most advanced on the market today. We use sophisticated impedance matching and mode controlling techniques to provide the widest bandwidth in the industry. We have developed a new wideband hybrid circulator technology. The hybrid circulator has significantly higher bandwidth than the Y-junction. The hybrid circulator is an enabling technology for broadband transmit/receive applications.
-
Product
Coaxlink Mono CXP-12 LH
-
One CoaXPress CXP-12 connection: 1,250 MB/s camera bandwidthPCIe 3.0 (Gen 3) x4 bus: 3,300 MB/s bus bandwidthLow-profile card. Delivered with standard and low-profile bracketsPassive (fanless) heatsinkFeature-rich set of 10 digital I/O linesExtensive camera control functionsMemento Event Logging Tool
-
Product
CANKeypad
-
Programmable keypad designed for seamless system integration. Enable smart control of components like lights, pumps, and motors—even without a display. With a rugged sealed housing, tactile silicone buttons, and adaptive brightness, the CANKeypad delivers reliable performance in any condition.
-
Product
Rotary Actuators
-
Electrical rotary actuators with rated torque of 100 Nm ... 16000 Nm for the operation of final control elements with preferably 90° rotary movement such as flaps, cocks, dampers, etc.A lever / linkage bar assembly transfers the torque or the actuator is directly coupled to the cock flange.
-
Product
Automated Analysis Software
RevospECT Pro
-
RevospECT Pro is the industry’s first commercially available high-powered, adaptable and scalable automated analysis system. It provides end users the power and control to perform comprehensive automated analysis of eddy current data. RevospECT has a proven track record in the field and meets rigorous industry standards for flaw analysis from bobbin, rotating and array inspection techniques. Once configured for an inspection, RevospECT Pro will process and analyze data at an extremely fast rate utilizing its robust distributed processing power, often outpacing data acquisition rates and generating results that can be verified immediately by the reviewing data analyst. More importantly than system speed is the consistency of the results that are delivered using computer-aided analysis.
-
Product
GPIB Interfaces
-
Control older devices that use the ANSI X3.28 protocol from the GPIB Bus. Available in board or rack mountable Minibox™ form.
-
Product
High Density Switching & Distribution UnitLinker System
LS1601A
-
Universal Switching Corporation
For Communication, Telemetry, ATE and Broadcast Installations. Continuing to expand our distribution product offerings, the new LS1601A offers a fresh new alternative to system engineers. The 3RU rack mountable unit has a unique "open window" front panel design that allows up to sixteen plug-in modules to be installed with both forward and rear facing connectors, controls, and indicators. For control and monitor, a plug-in LXI certified 10/100 Ethernet module can be installed
-
Product
cDAQ-9181, 1‑Slot, Ethernet CompactDAQ Chassis
781496-01
Chassis
1‑Slot, Ethernet CompactDAQ Chassis - The cDAQ‑9181 is a CompactDAQ Ethernet chassis designed for small, distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis also has four 32‑bit general‑purpose counters/timers. You can access these counters through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement.
-
Product
Pressure Controllers
-
We offer pressure controllers as portable and as workshop models. We have automatic pressure controllers that can be used as stand-alone controllers or that can be combined with our calibrators to enable automatic paperless calibrations. We also offer manual pressure generators; hand pumps and manual pressure controlling modules.
