-
product
Deep Packet Inspection
FlowPro
FlowPro is inserted into areas of the network when visibility is needed. It uses a deep packet inspection (DPI) to compile a flow cache, and exports traffic and threat details reflecting 100% of all communications that pass by. FlowPro is a great complement to the Scrutinizer Incident Response System and ensures the security team has insight where they need it.
-
product
DIP Tester
Model DS-10
Putting it a conveyor to flow through a solder bath to obtain information needed to manage it. The created temperature profile makes it possible to monitor the 50ms sampling temperature of the preheat and solder temperature sensors in addition to the conventional management items.
-
product
Mechanical Shock Test System
BW-MST-E5000
The Mechanical Shock Tower develops the kinetic energy electromagnetically. An iron core "bullet" is attracted to the magnetic core of the solenoid by the dense magnetic field that is created as current flows through the field coil of the shock tower. As the bullet is drawn into the center of the magnetic field the acceleration increases exponentially as the gap reduces to zero on impact causing the high impact shock
-
product
Pressure Switches
Whitman controls offers the most diverse selection of pressure switches in the industry. Our diverse line of switches are used across a wide range of applications including blowers, generator sets, off-road vehicles, compressors, wafer ovens, process equipment, flow control devices, pumps, wastewater, heating and cooling systems, and numerous other applications across industries.
-
product
Air Flow Meter
DBM 620
The newly redesigned DBM 620 Air Flow Meter is a multipurpose electronic air balancing instrument primarily used for efficiently taking direct air volume readings from air vents.
-
-
product
Ultrasonic Exhaust Flow Meter for Real-time Measurement of Vehicle/Engine Exhaust Flow
EXFM-ONE
EXFM-ONE employs an ultrasonic method for measuring exhaust gas flow rates directly from a vehicle or engine. The unit can be used for various applications such as real time mass measurement of raw exhaust gas combined with MEXA-ONE (Motor Exhaust Gas Analyzer), or for Particulate Matter/emission measurement combined with partial flow dilution system such as MDLT (Partial Flow Dilution Tunnel) or BMD (Bag Mini Diluter). Fuel consumption evaluation is also available when EXFM-ONE is paired with an optional air-to-fuel ratio (AFR) analyzer.
-
product
Salt Fog Chambers
SCCH
Seamless, oven-cured vinyl lining for maximum service life and corrosion resistanceClear acrylic cover optimizes test observation. Individual temperature display for Dry Bulb, Wet bulb and Humidifying tower. Internally-baffled Opti-fog® tower for uniform atmosphere and efficient solution usage.Air Flow Meter - Convenient indication of Opti-fog® performance without waiting hours for collection rates.Level-Matic® Reservoir Assembly Automatically maintains proper solution levels to Opti-fog® and Humidifying Tower. Standard operating temperature of ambient to 120°F/49°C (higher temps optional)Fully tested and certified prior to shipment.
-
product
Process Gas Condenser/Chiller
Process gas chillers are designed to condense vapors out of a process gas stream so it may be collected and properly disposed.This chiller condenses Styrene (a gas that is regulated by the E.P.A.) out of a process gas stream. The chiller operated continuously at a -25C (-13F) outlet air temperature as long as the process gas stream was flowing.
-
product
Error Proofing Applications
ARC has assisted in Error Proofing critical processes at many companies like yours, to implement visual based process verification, data-centric process flow and, if needed, connected tooling that can be combined to improve your operation. By providing a process verification system that can be connected into your manual and automated processes, you can achieve your error proofing goals.
-
product
Averaging Pilot Tubes
Meriam manufactures the widest range of Averaging Pitot Tubes for gases, liquids and steam with bi-directional flow capability. Under the Accutube brand name, there are four standard models; Inline, Insertion, Flanged and Wet Tap which can provide a flow solution for your toughest applications. To provide the complete flow solution that meets your specific needs, we can provide DP or Multivariable transmitters from the brand of your choice, or we will recommend the best fit for your application. These transmitters can be installed on the Accutube and configured to your specific flow requirements here at Meriam by qualified technicians, reducing your expense and time .
-
product
Renewable Energy Loggers
Data Loggers measure AC & DC circuits for Renewable Energy installations. Record directional flow of current, determine patterns when your system is importing or exporting to the grid.
-
product
Positive Displacement Meter
The Blancett positive displacement flow meter provides high measurement accuracy for fluids over a wide viscosity range. Applications include lubricants, fuels, chemicals and solvents, oils and greases. With only 2 moving parts, the positive displacement meter offers trouble free operation and long service life. The meter is bi-directional and it has an extremely large turndown ratio, up to 400:1 in some models - with full accuracy at extremely low flow rates.
-
product
Calibration Gas
Cambridge Sensotec supplies bespoke gas calibration kits for our O2 and SF6 gas analysers, as well our gas detection & MAP product ranges. Each kit has the appropriate calibration gases and flow regulator supplied in a convenient carry/storage case.
-
product
Multiphysics Simulator
The COMSOL Multiphysics simulation environment facilitatesall steps in the modeling process defining your geometry, specifying your physics, meshing, solving and then post-processing your results. Model set up is quick, thanks to a number of predefined modeling interfaces for applications ranging from fluid flow and heat transfer to structural mechanics and electromagnetic analyses.
-
product
Shear Stress Sensors
DirectShear™
Micromachined floating element shear stress sensor that enables time-resolved, one-dimensional, direct shear stress measurements. Direct measurement of shear stress — no heat transfer calibration. Non-intrusive — minimal flow disturbance. Simultaneous mean and fluctuating shear stress measurements. High resolution, dynamic range and bandwidth. Highly accurate, quantitative measurements.
-
product
Flow Instruments
Omega has one of the largest inventories of flow instrumentation and accessories in the industry. We have everything from flow meters, anemometers, flow switches, valves, and flow accessories.
-
product
Fuel Density Meter
FD-5110
By connecting with the FM-3100 Digital Flow Meter, the FD-5110 Fuel Density Meter can measure temperature and density data in real time. In addition, the FP series Volumetric Flow Detectors with wide range ability and the FD-5110 are the best choice for achieving the accurate mass flow measurement.
-
product
Debug Fixture
With at-speed test, debug can easily become a problem: If test points are on the bottom, as is often the case for test processing, then this requires the board to be flip over for the debug. However, during at-speed testing, key devices and signal paths are often on the topside. IST Engineering has in-house expertise with debug fixtures, which allow the test technician to flip over a test board, or even hold it vertically for dual-sided access, while still running the Device-Under-Test at full-speed through card-edge connectors - whether these are standard DIN type or F or N type co-ax connectors. The debug stations are constructed robustly, with metal frames and high-grade flexible cabling and can also be used as backup test stations in a manufacturing flow. They can be built with custom machined waveguide connections for RF/Microwave applications, or with standard, off the shelf connectors, as defined by the application. A number of these debug fixtures are in production use with a range of customers.
-
product
AC & DC Aging Test Equipment for Arrester Valve Plate
Shanghai Guantu Technology Co., Ltd.
The arrester is usually connected between the live wire and the ground, and is connected in parallel with the protected equipment. When the overvoltage value reaches the specified operating voltage, the arrester will act immediately, flow the charge, limit the overvoltage amplitude, and protect the insulation of the equipment; when the voltage value is normal, the arrester will quickly return to its original state to ensure the normal power supply of the system.
-
product
Portable Dew Point Monitor
1500
The Model 1500 is a self contained system; not only is there no field assembly required, there’s no need to carry around a myriad of individual components such as control boxes, sensors, cables, pumps, and power cords. Simply attach the sample line, adjust the flow (with the integral flow meter) and turn on the power. Within minutes you’ll be collecting field dew point data with the same chilled mirror accuracy of a lab standard hygrometer. And with a nominal battery life of 12 hours, you will be able to collect for the entire shift or spot check your processes for several days.
-
-
product
Pressure Sensors
Pressure sensors have particular utility for monitoring the pressure in a fluid network. As compared with flow sensors, pressure sensors often require less cost to achieve a similar result. Pressure sensors are often fabricated using thin membranes that flex under pressure.Some pressure sensors function in a binary manner, i.e., when pressure is applied to a pressure sensor, the sensor acts to complete or break an electical circuit. Some speed cameras use them.
-
product
Tracer Gas Leak Test Systems
Tracer gas leak testing is a simple and highly-efficient method of leak detection that provides high sensitivity as well as increased accuracy and repeatability. This method is used for testing parts with very low leak rates that are outside the range for conventional air-flow pressure decay and mass flow, or to replace bubble test methods. Tracer gas testing uses escaping tracer gas to identify micro-leaks in the range of 1x10-4 to 10-9 scc/s.
-
product
Static Design Verification
ALINT-PRO
ALINT-PRO™ is a design verification solution for RTL code written in VHDL, Verilog, and SystemVerilog, which is focused on verifying coding style and naming conventions, RTL and post-synthesis simulation mismatches, smooth and optimal synthesis, correct FSM descriptions, avoiding problems on further design stages, clocks and reset tree issues, CDC, RDC, DFT, and coding for portability and reuse. The solution performs static analysis based on RTL and SDC™ source files uncovering critical design issues early in the design cycle, which in turn reduces design signoff time dramatically. Running ALINT-PRO before the RTL simulation and logic synthesis phases prevents design issues spreading into the downstream stages of design flow and reduces the number of iterations required to finish the design.
-
product
Regulators
Parker offers a range of air-line, pressure high flow and single phase regulators for instrumentation, filtration, refrigeration and pneumatic applications. Instrumentation regulators are used in the process, power, oil, gas and semiconductor industries to control the flow of liquids and gases with speed and precision. Air regulators provide quick response and accurate pressure regulation for the most demanding industrial air preparation applications, available as miniature, economy, compact, standard, hi-flow and pilot-operated regulators to meet a variety of service needs. The refrigeration line of pressure regulators includes valves that control inlet, outlet or differential pressure. Each regulator is available with an assortment of variations which enable one regulator to perform multiple functions. All regulators are built to the highest quality standards, recognized around the world for their performance, durability and reliability.
-
product
Functional Testing Service
Is your software working the way it is intended to? Will it work in the real world as it does in simulations? Is the code really executing as per its outlined specifications? Do various parts of the application interact as planned? Will users find the application functioning as per their requirements or will they get lost in the flow? Functional testing answers all these questions and more:- Tests your application against its intended output parameters to make sure it works the way it is meant to.- Tests if the functions of the application are working as intendedUnderstand if various parts of the application are interacting as planned.- Check if the user navigation is simple, free-flowing, and friction-less.- Functional Testing ensures optimum quality for content, design and user experience.
-
product
Network Interface Card
NIC10G
Featuring the Intel 82599ES dual 10GbE controller, the NIC10G supports flow control, integrated IPsec security engines, optimized queues, IPv6 offloading, advanced filtering capabilities, and Tx/Rx IP, TCP and UDP checksum offloading capability. Also has integrated a PCI Express Gen 2 interface supporting up to 8 lanes.
-
product
Subsea Multiphase Sampler
The Mirmorax Subsea Multiphase Sampling System provides the operator with a sample that, independent of flow regime and compositional mix, is a true volumetric representation of the flow.
-
product
Candlestick Sensor
Advanced Thermal Solutions, Inc.
The Candlestick Sensor is a flexible, robust, base-and-stem design air velocity sensor that measures both temperature and air velocity for characterizing thermal conditions in electronic systems. The Candlestick Sensor is narrow and low profile to minimize the disturbance of the heat flow in the test domain. It features a flexible, plastic-sleeved stem, which facilitates installation and repositioning during the testing process.
