Product

EMI Receiver

Core-6

-

FRANKONIA GmbH

Core-6 - FRANKONIA GmbH

The "CORE-6" is a very compact (19", 1 RU), new digital EMI receiver which enables the user to make frequency-sweeps within a few seconds what saves hours of measuring timeduring developments.

Product

​Coaxial Receiver Protector

-

Teledyne Lincoln Microwave

Teledyne Lincoln Microwave

Where size, weight and power handling are the principle constraints, a TLM air-spaced coaxial limiter range provides an excellent compromise between waveguide and microstrip limiters. These devices are able to withstand higher power levels than microstrip solutions but still retaining a relatively compact package, Teledyne’s designs offer a low insertion loss and incorporate the same wide range of features as our waveguide limiters. Suitable for continuous operation at peak power levels of several kW's and mean power levels of 100's watts with sub- microsecond recovery time - over 10% bandwidth in <100mm length (at S-Band).

Product

Transmitter / Receiver Modules

-

Appointech, Inc.

Appointech, Inc.

An RF module (radio frequency module) is a (usually) small electronic device used to transmit and/or receive radio signals between two devices. In an embedded system it is often desirable to communicate with another device wirelessly. This wireless communication may be accomplished through optical communication or through radio frequency (RF) communication. For many applications the medium of choice is RF since it does not require line of sight. RF communications incorporate a transmitter and/or receiver.

Product

Optical Receiver Stress Test Solution

N4917B

-

Keysight Technologies

N4917B - Keysight Technologies

The N4917B software provides an automated standard compliant stressed receiver sensitivity test according to 100GBASE-LR4, ER4 and SR4 test specification. In order to do this kind of test, several test instruments such as a bit error ratio tester, digital sampling oscilloscope, optical reference transmitter and tunable laser source are required to operate together to achieve a compliant, repeatable optical stressed eye. This stressed eye is then fed to the receiver under test, where bit error ratio is measured under the stress conditions as defined in the standard.

Product

Airborne Receiver

MS 2015

-

Meltronics Systemtech

MS 2015 - Meltronics Systemtech

Receiver shall receive the telemetry signal transmitted by the airborne TGS unit. This unit is a single conversion super heterodyne FM receiver operating at 1486.5MHz. This unit has four connectors. They are RF input connector (J1), Power connector (J2), Signal connector (J3) for AGC signal and a Video output connector (J4). This unit operates at 28V DC and consumes a typical power of 5.6 watts.

Product

Low Cost Microwave Wideband PIN Preamp Receivers

MR21 (40KHz~18GHz)

-

Hangzhou Huatai Optic Tech. Co., Ltd.

MR21 (40KHz~18GHz) - Hangzhou Huatai Optic Tech. Co., Ltd.

MR21 series microwave wideband optical receiver, adopts High linear PIN diode and Low noise pre-amplifier IC, within bandwidth of 40KHz~18GHz, they are featured with excellent linearity, high responsibility and superior flatness of the RF response in both, power and phase. They provide an outstanding linearity fiber optical communication for analogue wideband microwave application. Due to avoidance of using expensive coaxial cable or wave guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless, timing and reference signal distribution, telemetry, measurement and delay line etc as well as 10Gb/s and 18Gb/s high speed communication system.

Product

MIPI Receiver Test Solution

M8085A

-

Keysight Technologies

M8085A - Keysight Technologies

The M8085A is a software plug-in for M8070A Bit Error Ratio Test system software within the M8000 series of BER test solutions. The M8085A software plug-in controls either the M8190A or the M8195A Arbitrary Waveform Generators to create C-PHY or D-PHY standard compliant test signals. In addition it provides routines for calibration of all signal parameters and for all tests specified in the applicable Conformance Test Suite. Together with the additional available DUT control interface it is possible to read the BER of the receiver under test from the M8070A software and display the BER dependency from test parameters within the M8070A user interface.

Product

8 Way GPS / GNSS Signal Splitter Passive, 1-2 GHz, N Type, DC Block+200Ω Load 8 Ports

GPS802

-

INSTOCK Wireless Components, Inc

GPS802 - INSTOCK Wireless Components, Inc

GPS L1 - L5, GLONASS, Galileo splitterLow Insertion Loss (0.6 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)15 VDC & 75 mA max on DC block portsTri Alloy N Type Female (Jack) 50 Ohm

Product

Measuring Receivers

-

Rohde & Schwarz GmbH & Co. KG

Rohde & Schwarz GmbH & Co. KG

Calibration and performance check of signal generators and attenuators

Product

EMI Test Receiver

SER

-

Saluki Technology Inc.

SER - Saluki Technology Inc.

Saluki SER series EMI receivers comply with CISPR 16-1-1 standard, integrated CISPR-AVG, CISPR-RMS, QPK detectors, and electromagnetic interference measurement. According to CISPR, EN, FCC and MIL standards, which is suitable for EMI testing in home appliances, lighting, automotive electronics, medical, and other industries. Combined with ETR PC measurement software and a wealth of test options, accurate automated testing is possible. The whole system is equipped with a spectrum analysis module and a tracking signal generator to meet the testing needs of users in different fields.