Filter Results By:
Products
Applications
Manufacturers
Multipliers
-
product
Single-phase Electricity Meters
Single-phase static electricity meters AMS B1x-SAx are determined for direct and indirect measurement of active energy displaying value on mechanical register with stepping motor. In the case of CT (current transformer) operated meters (x/5A) it is necessary value of register to multiply by the current transformer ratio.
-
-
product
Bandpass Filters
These bandpass filters utilize a suspended stripline design to obtain a very compact configuration. Applications include wideband receiver input preselection and output filtering of frequency multiplied RF power sources.
-
product
Frequency Multipliers (WR and D Series)
VDI offers a broad range of millimeter-wave varistor mode, passive frequency multipliers based on planar GaAs Schottky diode technology. Frequency doublers and triplers are used to extend the frequency coverage of microwave and millimeter-wave sources.
-
product
Torque Calibration
ISO 17025 Accredited Calibration for Torque Screwdrivers, Torque Wrenches, Torque Multipliers, Torque Transducers, Torque Watches, and Torque Readout
-
product
Pulse Signal Amplifier
VCH-606
The pulse signal amplifier VCH-606 is designed to multiply a single pulse or a sequence of pulses to 16 independent outputs. The impulse signal amplifier includes 16 independent channels with unity gain each for connecting consumers of impulse signals with an input impedance of 50 Ohm.
-
product
High Speed Test Bench
AT444
AC motor with mechanical multiplying gearbox test benches allow precise programming of all drive parameters required for accurate rotating devices test.The use of special high-speed bearings, mechanical components and parts wear resistant leads to a large life. The supply includes the electronic drive and control as well as the entire oil cooling unit.
-
product
Low-Power General Purpose FPGA
Certus-NX
*Up to 39K logic cells, 2.9 Mb embedded memory, 56 18 x 18 multipliers, 192 programmable I/O, one lane of 5 Gbps PCIe, two lanes of 1.25 Gbps SGMII, two ADCs (each 12-bit, 1 MSPS).*Packages as small as 6x6 mm, and in ball-pitch options of 0.5 and 0.8 mm.*Power modes – User selectable Low Power vs. High Performance modes, enabled by FD-SOI programmable back-bias.*Design security – ECDSA bitstream authentication, coupled with robust AES-256 encryption.*Instant-on configuration – I/O configures in 3 ms, and full-device as fast as 8 ms.*Available in Commercial, Industrial and Automotive (AEC-Q100 qualified) temperature grades.
-
product
6U VPX FPGA Cards
Curtiss-Wright Defense Solutions
FPGAs have revolutionized the way digital signal processing (DSP) subsystems are configured. With a large number of gates, hardware multipliers, and high-speed serial interfaces, FPGAs enable sophisticated applications, including radar, signal intelligence, and image processing, which rely on repetitive processing that can be expressed in highly parallel form. FPGAs perform exceptionally well in FFTs, pulse compression, filters, and digital up/down converters.
-
product
High-Frequency Signal Amplifier
VCH-605
High-frequency signal amplifier VCH-605 is designed to amplify and multiply sinusoidal signals with a frequency of 1-100 MHz.
-
product
Two Channel Phase and Amplitude Noise Analyzer
DCNTS -190
The DCNTS is a two channel Phase and Amplitude noise analyzer. Its dual demodulator architecture allows the system to use cross-correlation to cancel its internal noise and limitation; it is like comparing the outputs of 2 systems and only display the similarities while rejecting differences. Its main extension is the Residual Noise measurement front-end which includes all necessary hardware to automatically measure residual noise on 2-ports devices either in RF frequencies or microwave. It could be a frequency multiplier or divider, an amplifier or any other phase coherent input to output device.
-
product
Analog Multipliers & Dividers
An analog multiplier/divider is a device that produces an output voltage or current that is proportional to the product of two or more independent input voltages or currents. In addition to multiplying and dividing, multipliers can perform squaring, square-rooting and modulation functions. Applications include radar, communications, and industrial controls where a real-time response is required. Analog Devices’ offers the widest selection of multipliers and dividers.
-
product
Photomultiplier
PMT-101
Photo Multiplier Tube with a range of 185 - 700 nm. Has a built in power supply. Built in low noise amplifier with a gain of x1 and x100.
-
product
Electric Multipliers
EFC
The easy-to-operate EFCip electric torque multipliers are designed for precision tightening and loosening of all heavy duty fastening applications. From tightening large industrial bolts used in windmill gearbox assemblies to bolting maintenance applications for oil & gas pipelines and rigs, the Mountz torque multipliers achieve precision torque in a quick, cost-efficient manner.
-
product
Frequency Multipliers
Macom Technology Solutions Holdings Inc.
At MACOM we offer a line of frequency multipliers that can be used in a variety of communications applications. Our multipliers cover frequencies to 50 GHz and combine an active Doubler with an output buffer amplifier to deliver constant power over a range of input powers, resulting in an excellent rejection of the fundamental and harmonic products. MACOM’s multipliers are available as bare die or in surface mount lead-free QFN packages.
-
product
VXI Digital Multiplier
4152A
The 4152A’s advanced features like limit testing, averaging, speed/resolution trade-offs, and fast function changes provide the high “test system” throughput required in today’s production test environments.
-
product
Full Band Noise Figure and Gain Test Extenders
STG-06-S1
Full band noise figure and gain test extenders are offered to extend noise and gain measuring capabilities up to higher millimeterwave frequency ranges. These extenders are designed to interface with noise and gain test systems that have an input IF of 10 MHz to 1.6 GHz, such as the industry standard Keysight 8970A/B, N8975A and Maury MT 2075B. The noise figure and gain test extenders include a high-performance, solid-state noise source (STZ series) and a full waveguide down converter (STC series), which consists of a Faraday isolator (STF series), full band mixer (SFB series), frequency multiplier, and IF amplifier. A frequency source with an output signal in the frequency range of 10 to 20 GHz is required as a local oscillator for the down converter. The noise source is automatically powered on and off by the noise figure meter.
-
product
Active Frequency Multipliers
The frequency multiplier which generates output signal with power greater than or equal to input power
-
product
Get Flexible, Get FlexiFLASH
LatticeXP2
*Up to 885 Kbits sysMEM™ embedded block RAM and up to 83 Kbits distributed RAM*sysCLOCK™ PLLs up to four analog PLLs per device that enable clock multiply, divide and phase shifting*Three to eight sysDSP blocks for high performance multiply and accumulate.*Pre-engineered source synchronous IOs for DDR/DDR2 up to 200 MHz and 7:1 LVDS interface support up to 600 Mbps*Available in csBGA, TQFP, PQFP and BGA packaging
-
product
Full Band Down-Converters
STC-20-10-S1
Full band down-converters are designed to convert high frequency millimeterwave signals down to the baseband at 10 MHz to 1.6 GHz. These down-converters deliver a superior performance since they are assembled with SAGE Millimeter’s instrumentation grade components, such as multipliers, amplifiers, filters, isolators, and more. The below standard offering covers the frequency range of 26.5 to 170 GHz and delivers a typical LO power of 3 dBm and conversion gain of 20 dB. The down-converters provide low harmonic levels and excellent gain flatness, making them ideal for test instrumentation applications. Specifications other than those listed below are available upon request.
-
product
Passive probe with X1/X10 switch
They are normally designated X1 and X10, although 1X and 10X are sometimes seen. The designation refers to the factor by which the impedance of the scope itelf is multiplied by the probe.The X1 probes are suitable for many low frequency applications. They offer the same input impedance of the oscilloscope which is normally 1 MΩ. However for applications where better accuracy is needed and as frequencies start to rise, other test probes are needed.
-
product
Comb Generator/Frequency Multiplier
TBCG2
The TBCG2 is a passive, step recovery diode based comb generator/frequency multiplier. It is optimized for moderate drive power and spectrum flatness in the frequency range 1 MHz to 2.5GHz.
-
product
Advanced Throughput Multiplier Feature, GTE 10.00p
K8215B
The Advanced Throughput Multiplier feature allows you to test up to two 1000 to 2000 node (between 1296 and 2592 nodes) boards simultaneously on a 4 module tester, thus dividing the test time by half.
-
product
Phase Detectors
Macom Technology Solutions Holdings Inc.
MACOM's MSPD Series Integrates an SRD reference frequency multiplier, coupling capacitors and a Schottky diode microwave sampler / phase detector in a 0.075” by 0.100” hybrid. They are used to phase lock microwave oscillators up to 22 GHz to a much lower reference frequency by deriving a locking voltage from the sampled RF and the multiplied reference.
-
product
SSD
M.2 SSD (iSLC)
Innodisk M.2 (S42) 3IE4 is characterized by L3 architecture with the latest SATA III (6.0GHz) Marvell NAND controller. Innodisk’s exclusive L3 architecture is L2 architecture multiplied LDPC (Low-Density Parity Check). L2 (Long Life) architecture is a 4K mapping algorithm that reduces WAF and features a real-time wear-leveling algorithm to provide high performance and prolong lifespan with exceptional reliability.
-
product
Pneumatic Radial Gearing Multipliers
RCL
Radial gearing electric torque multipliers are designed for precision tightening and loosening of all heavy duty fastening applications. These multipliers are specially designed for heat plate exchanger applications. The torque multiplier shuts-off when the pre-set torque is achieved. It is non-impacting and operates at a smooth, continuous rotation.
-
product
Frequency Multipliers
A series of broadband frequency multipliers is available with output frequencies between 18 and 110 GHz. The use of GaAs diodes on a suspended substrate circuit allows an extremely compact device. Circuit symmetry is used to enhance either even or odd harmonics while suppressing unwanted odd or even harmonics. These devices can be used as higher order even or odd harmonic multipliers with reduced efficiency. All of these multipliers have maximum input power +23 dBm for temperature less than +50°C.
-
product
Radial Gearing Multipliers
Mountz radial gearing torque multipliers are specifically designed to meet the needs of companies servicing plate heat exchangers in HVAC, chemical, dairy, marine, and petrochemical applications. Able to deliver repeatable, accurate amounts of torque, Mountz radial gearing torque multipliers prevent damage to plate heat exchangers during routine service, reducing the risk of expensive unplanned equipment downtime. The low profile heads of Mountz radial gearing torque multipliers allow them to fit into tight access points, helping you work more effectively. With over fifty years of direct industry experience, Mountz tools can be trusted with the costly assets your company relies on.
-
product
Radar Front Ends (FMCW)
FMCW Series
Farran’s 77 GHz FMCW Radar front end is based on a GaAs MMIC chipset offering wide bandwidth in a small outline package.The transmit signal is derived from an external VCO signal, internally multiplied, which also acts as the LO for the receive mixer. The resulting IF is conditioned for gain and filtering as required. The IF also contains an industry leading IF noise figure, especially in the frequency range below 500MHz. Custom designs available, visit our custom design page for more information.
-
product
Pneumatic Multipliers
CLS
The CLS pneumatic torque multiplier provides precision tightening and loosening of all heavy duty fastening connections. The torque multiplier shuts-off when pre-set torque is achieved. It's a non-impacting and operates at a smooth, continuous rotation, the torque multiplier increases speed and productivity, as it is faster than a hydraulic wrench and is less expensive.
