Discrete Device
semiconductor typically having one circuit.
-
Product
Angle Measurement Devices for Vehicles
ANGLE MEASUREMENT IN VEHICLES
-
F. W. Breithaupt & Sohn GmbH & Co.KG
*Development, manufacture according to customer inquiries*Many decades experience in project managment and solutions for special vehicle devices*Mechanical and mechatronical solutions*Made in Germany
-
Product
Hardness Testing Devices
-
Institut Dr. Foerster GmbH & Co. KG
NewSonic’s hardness testing devices test hardness in a nondestructive way using the UCI method (ultrasonic contact impedance). The testing procedure enables quick and mobile measurements (1-second type) to supplement traditional hardness testing. The devices feature compact measurement probes which can also be used in difficult testing positions and component geometries. The areas of application include incoming goods inspection, mix-up checks, production controls, quality assurance, weld seam inspection, cut edge checks, maintenance of built-in components, as well as the replacement of dynamic hardness testing devices in the case of thin materials (below 50mm, e.g. boilers, pipes)
-
Product
Machine Vibration Monitoring Devices & Systems
Spider-80x
-
*Route Based Vibration Data Collection*Remote Condition Monitoring Software*Vibration Diagnostics System
-
-
Product
Passive Tapping Device
DSL Phantom™
-
DSL Phantom™ is a unique passive tapping device for Lawful Interception (LI) of ADSL lines. The device records and stores broadband digital information, offering unique advantages to Law Enforcement Authorities (LEAs) looking to capture data between the target and the service provider premises.
-
Product
Conversion Devices and Adapters
-
Conversion devices and adapters fulfill several roles. For example, you can use them to convert an output signal to a signal type that can be measured by a data logger, to adjust resistive bridge measurements, or to build distributed measurement networks.
-
Product
Test Devices
-
qCf - quickCONNECT - efficient, accurate, safe!Measurements on internal components of the fuel cell and electrolysis
-
Product
Mask Foreign Matter Inspection Device
PR-PD2HR
-
Efficient foreign matter inspection and measurement with high yield.
-
Product
PoKeys I/O devices
-
This board allows expanding the number of outputs of the Pokeys by using the PoExtBus. This board incorporates 16 high current/voltage open collector outputs which suits applications such as lamps, relays.
-
Product
Free Modbus Device Tester Software
-
Global Multimedia Private Ltd.
This software was developed to test Information Displays made by Global Multimedia for modbus protocol compliance. It can be used to test your firmware on a serial device for Modbus RTU conformance.
-
Product
Thunderbolt 3 Portable Devices
-
Abaco's Thunderbolt 3 enabled family of products deliver the highest data-rates and lowest latencies for portable AFDX/ARINC664, ARINC 429, and MIL-STD-1553 avionics devices that are compatible with the latest generation of PC and Laptops.
-
Product
Optical Device
-
Optical devices are products that use the optical characteristics (birefringence) of quartz crystals. Murata Manufacturing uses high-precision synthetic quartz crystals grown using our proprietary technology to manufacture high-grade products.
-
Product
GPIB-RS232, Instrument Control Device - Korea 220VAC
779732-09
GPIB Controller
The GPIB‑RS232 is an IEEE 488 controller device for computers with an RS232 port. You can use this device to integrate an instrument into your system using GPIB. This device transforms a computer with an RS232 serial port into a talker, listener, or controller on the GPIB bus. It can also interface RS232 instruments and peripherals to the GPIB bus. It can implement the physical and electrical specifications of the IEEE 488 and RS232 standards, as well as interpret and execute high-level commands from the serial port, including RS232‑to‑GPIB and GPIB‑to‑RS232 protocol conversions. This device is IEEE 488.2 compatible. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
OLLI - gas detector / measuring device
-
Gas measurement & warning instrumentExplosion-proof & compact handheld gas measurement instrumentas diffusion device. It can be used for up to 5 combustible and toxicgases as well as oxygen and comes in an extremely rugged2C synthetic housing with a Li-Ion rechargeable battery.Explosion-proof measurement instrument formethane (CH4),propane (C3H8),oxygen (O2),carbon monoxide (CO),carbon dioxide (CO2),hydrogen sulfide (H2S)
-
Product
32-CH Discrete Input Modules
HSL-DI32-M-N/HSL-DI32-M-P
Digital Input Module
- Slave ID consumption: 2 consecutive from odd- "N" type for NPN sinking type sensor or dry contact; "P" type for PNP sourcing type sensor or wet contact- Photo couple isolation voltage: 2500 Vrms- Input impedance: 4.7 KΩ- Input current: ± 10 mA (Max), ± 12.5 mA (Peak)- Input voltage: ± 40 V (Max)- LED indicator: Power, Link and Input status- Power supply: +10 V to +30 VDC
-
Product
Imaging Devices
-
High quality imaging devices with double or simple telecentric objectives offering exceptional spatial resolution with high FOV. Dedicated to high quality measurements whatever your display size.
-
Product
Analog Measuring Devices
-
PeakTech Prüf- und Messtechnik GmbH
Is able to measure currents in the range 0 - 50 µA DC with high accuracy due to its scale measuring range. This inexpensive device is for use as a desk device / bench device, which do not need a powersupply to measure the in coming currents. The correct measured values can be conveniently read by the student on the large analog mirror scale.
-
Product
96-Pin SCSI Micro-D Discrete Wire
40-962-096-F
SCSI Female Connector
This connector is designed to allow users to terminate discrete wires with IDC connections to the 96-Pin SCSI Style Micro-D connector. Pickering Interfaces recommends the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
Product
Wire Damage Test Device For Pull Testing
IEC60884 FIG11
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884 FIG11 Wire damage test device for pull testingThe wire damage test device is a special test instrument designed and manufactured according to the requirements of IEC884 Figure 11, , etc. It is mainly used to judge whether the screw-clamp type terminal is in design and structure.
-
Product
Electronic Load Device
786530-01
-
The RMX-4004 provides capabilities for qualifying power designs and validating power supply functionality in a production environment. You can combine Electronic Load Devices to customize your test system based on the number of channels, maximum load power, and voltage and current of each channel.
-
Product
100-Pin Micro-D Connector, Male, Discrete Wire, 2-56 UNC Screwlocks, Metal Shell
C100SMR-1CW-6A
-
This accessory is designed to allow users to directly terminate a cable to the connector. It is difficult to terminate cable to the 100-Pin SCSI Style Micro-D connector because of the high density and fine pitch. Pickering Interfaces recommends the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
Product
Power Devices & Power Conversion
-
CAES has a legacy of supplying high-performance power and power conversion products to the aerospace market, providing ground power to fighter jets and other aircraft and assisting with applications such as aircraft engine starting.
-
Product
USB-8506 , LIN Interface Device
784664-01
LIN Interface
1- or 2-Port, USB LIN Interface Device—The USB‑8506 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver. The USB‑8506 is powered over the USB bus and does not require external power. The USB‑8506 excels in applications requiring logging or manipulation of hundreds of LIN frames and signals, such as in-vehicle data logging, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move LIN frames and signals between the interface and the user program without CPU interrupts, minimize message latency, and free host processor time. The USB‑8506 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
1-Port RS-232/422/485 Serial Device Server
EKI-1521
-
Provides 2 x 10/100 Mbps Ethernet ports for LAN redundancyProvides COM port redirection (Virtual COM), TCP and UDP operation modesSupports up to 921.6 kbps, and any baud rate settingAllows a max. of 5 hosts to access one serial portAllows a max. of 16 hosts to be accessed as TCP client modeBuilt-in 15 KV ESD protection for all serial signalsProvides rich configuration methods including Windows utility, Telnet console, and Web BrowserSupports 32-bit/64-bit Windows 2000/XP/Vista/7/8/8.1/10, Windows Server2003/2008/2012/2016, and LinuxAutomatic RS-485 data flow controlSupports line to line 2 KV, line to ground 4 KV surge protection
-
Product
USB Device Server
-
Advantech USB serial device server allows PC users to connect serial devices via a LAN to systems. They allow access from anywhere on your network.
-
Product
Data Acquisition Device A2D / D2A
-
General Features10 DAC channels5 ADC channelsDifferential or single ended IOs Full scale bipolar or unipolar signaling
-
Product
GPIB Instrument Control Device
GPIB Controller
GPIB Instrument Control Devices offer IEEE 488 controllers that are compatible with ExpressCard, PMC, PCMCIA, PCIe, PCI, and USB slots as well as Ethernet, RS485, RS422, and RS232 ports. Some models can control multiple GPIB devices, and others offer sustained data transfer rates and no microprocessor interruption in data transfers. GPIB Instrument Control Devices include a license for the NI-488.2 driver software, providing maximum reliability for connecting to third-party instruments via GPIB. The devices are completely IEEE 488.2 compatible, have industry-standard transfer rates, and offer easy system configuration through NI software.
-
Product
Pull Out Device
BCL-1
-
This Pull out device BCL-1 is designed and manufactured according to relevant standard requirements of IEC884-1/ GB2099.1-2008 and other electrical accessories standards, Mainly used to test the needed maximum force when the plug pull out from socket and the minimum force when single stage plug pull out from socket, and to inspect whether the socket can withstand the lateral stress imposed by electric plug into the socket. This device is applied to plugs and sockets which rated voltage no more than 250V and rated current no more than 16A.Specifications: • Weights: 36N*1, 5.4N*1, 5N*2, 4N*1, 2.6N*1; • Standard testing plug: each one for Dipolar 10A, tripolar 10A and 16A • Standard test bolt: Each one for 1.5N and 2N • 1 set of clamping device • 1 set of Weights tray • Lateral stress weights 5N*1 • 1 set of lateral stress bar
-
Product
Seam Fold Test Device
FFR1000
-
This equipment is designed to bend a flexible printed circuit board, which has a high degree of freedom and versatility, and at that time, apply a load to the bending point at the initial stage or each time, and repeat bending and unfolding to confirm the durability.
-
Product
Resistance Measuring Devices
-
Professional electrical test tools used to measure ground earthing, low-ohm continuity, and protective conductor safety in industrial and electrical installations.
