-
product
Rockwell Hardness Tester
The most popular and widely used method of Hardness Testing, The Qualitest range of Rockwell Hardness Tester Range start from low cost analog models up to sophisticated and advanced load-cell type models. The popular, HardRocker, QualiRock, Rocky series hardness tester models have configurations suitable for Regular and/or Superficial Rockwell Hardness Testing, while our advanced Universal Hardness Tester Range can test the full Rockwell scale in addition to Brinell & Vickers. Qualitest also offers Automatic In-line hardness testers for high volume testing.
-
product
Digital Superficial Rockwell Hardness Tester Tallboy
900-349
This digital Superficial Rockwell hardness tester with fully automated load/unload procedures affords highly sensitive and accurate readings. Micro computer controlled with USB output to built-in mini printer or PC. The 900-349 digital superficial Rockwell hardness tester offers programmable scale conversions, dwell times, statistical capabilities and test counter. Capable of testing in all of the superficial Rockwell® scales.
-
product
Macro Hardness Testers
Macro hardness is the measurement of the hardness of materials tested with high applied loads.
-
product
Shore Hardness Tester
HT-6510
Application: shore A is designed to measure the penetration hardness of rubber, elastomers and other rubber like substances such as neoprene, silicone, and vinyl. It can also be used for soft plastics, felt, leather and similar materials. Shore D is designed for plastics, Formica, Epoxies and Plexiglass. Application: shore C is designed for various foam and sponge.
-
product
Gear Teeth Hardness Tester
PHT-1740
This dedicated unit is designed to test gear teeth and other difficult to access applications. The 1740 is an economically priced hardness tester that is loaded with the same features found on the base 1700 version. The 1740 hardness tester is capable of measuring the surface hardness of a broad variety of metals on flat and round surfaces. This instrument comes complete with a dedicated DL impact device, calibrated test block and rugged carry case.
-
product
Micro Hardness Testers
QATM micro hardness testers for Vickers, Knoop and Brinell cover a test load range from 0.25 g to 62.5 kg. All hardness testers are equipped with an intuitive software that allows easy operation, analysis, and documentation of results. Turrets with either 6 or 8 different test diamonds or lenses can be mounted, which makes switching between Vickers, Knoop and Brinell hardness testing very simple.
-
product
Bench Hardness Tester
Beijing TIME High Technology Ltd.
A stationary, heavy-duty instrument used for precise, repeatable hardness measurements of materials like metals and plastics in a controlled environment.
-
product
Rockwell Hardness Tester
The QATM Rockwell hardness tester series combines sophisticated design with technical innovation. A wealth of comfort functions make operation easy, safe, and fast. Modern software and interfaces allow time-saving automation and integration of the hardness tester into any lab. Due to the large test force range, Rockwell testing can be carried out for many different materials.
-
-
product
Hardness Test Blocks
Used to verify the hardness tester's performance and provide data in order to calibrate the hardness tester.
-
product
Barcol Hardness Impressor
BHI
Measures the hardness of soft metals such as aluminum, aluminum alloys, copper, brass, and other materials such as harder plastics, and fiber-reinforced plastic. Easy-to-read digital display. Comparable to 934-1 Barcol Hardness Tester. Conforms to national and international standards including ASTM.
-
product
Multifunctional Scratch Hardness Tester
Sataton Instruments Technology CO., Ltd
Multifunctional scratch hardness tester is an integrated testing instrument designed for cross hatch cut method and five-finger (five arm) method to measure scratch or mar resistance, hardness, susceptibility of a material surface to different physical damage like scratching, marring, scraping, etc. The tester are made of two parts, one is for determination of resistance to scratches and cuts according to cross-cut test for paints and varinishes. The other is for
-
product
Tablet Hardness Tester
* Complied with USP* Pretty design with an easy operation* The model can be rotated 180 degrees position to do an error calibration.* Sample diameter range: Ø3 ~ Ø30 mm* The model can double as a tensile tester.* Pressure gauge with a variety of specifications to provide choice.
-
product
Image Analysis Software
Offering you a complete choice of products which include brinell pro software, caliper pro software, cast iron analysis software, hardness pro image analysis software, live measurement software and material plus software.
-
product
E84 Recorder
GCI's industry leading E84 Recorder is used by FABs and OEMs worldwide to locate and resolve E84 handshake issues due to signal drops and external interference. It non-intrusively captures the states of all E84 signals during live material handoffs and records them to the connected PC's hard drive. Short- and long-term recording modes are available using E84 Analysis, GCI's industry leading diagnostic software.
-
product
Motorized Constant Loader
CLE-150 Series
When we measure the hardness of rubber test specimen etc. with durometer, we have the possibility to make an error for the result of the measurement. To make solution for such an important factor fo the error, CLE-150 Series is employed the motor driving system for the descent speed control, and then we could realize to measure the hardness of constant speed and constant pressure that is precise and reproducible.
-
product
Hardness Tester
Morehouse Instrument Company Inc.
An easy to use force measuring instrument able to meet the ever-increasing emphasis on product quality control demands for brinell hardness testing.
-
product
Extendible Test Leads
The Extendable Tip Probe permits testing in those hard to reach areas. The tips are fully insulated with durable Kynar. This prevents accidental shorting of adjacent components. The tip is stainless steel and is very sharp, allowing for penetration of conformal coatings. The rubber lead is 18 gauge, 48" long.
-
product
Ultrasonic Portable Hardness Tester
MET-U1A/MET-U1A50/MET-U1A100/MET-U1A110
The PHASE II ultrasonic portable hardness testers are capable of measuring the surface hardness of a broad variety of metals on flat, round, thin or large surfaces. Unlike the standard Dynamic hardness testers, these "state-of-the-art" portable hardness testers incorporate "Ultrasonic UCI" technology, which enables the hardness testing of very thin and small workpieces, which otherwise could not be tested accurately using a portable device.
-
product
DAS Antennas
In-Building Distributed Antenna System (DAS or i-DAS) antennas are low profile and designed to be mounted discreetly to a hard or tiled ceiling. Used in a series throughout large buildings, campus areas or even in below ground sections of a building the antennas can provide a distributed LTE or Wi-Fi signal to where it is required most. With a growing demand for in-building connectivity and higher data rates, larger smart or connected buildings require a series of antennas in order to distribute signal around the building or campus area.
-
product
XP2i Digital Pressure Gauge
AMETEK Sensors, Test & Calibration
We provide some of the world’s most popular XP2i digital test gauges for a variety of applications and markets. Included are intrinsically safe "percent of reading" gauges, process gauges, differential pressure gauges, panel mounted gauges, and gauges specifically designed for use in the maritime industry. Whether you’re looking for a gauge with long battery life to mount in hard to reach locations, a gauge to collect and store readings in the field in extreme conditions, or one that doesn’t require recalibration for up to three years, we have the perfect gauge for you.
-
product
Pen Type Leeb Hardness Tester
TIME®5100/5102/5104
Beijing TIME High Technology Ltd.
Pen Type Hardness Tester TIME®5100/5102/5104 is economically priced and suitable for quick hardness testing on metal materials, especially on-site hard testing of large, non-transportable components.
-
product
Electronic Safe & Arm Devices
Excelitas Technologies specializes in the design, manufacture, and testing of MIL-STD-1316 compliant Electronic Safe and Arm Devices (ESAD), Electronic Safe, Arm and Fire Devices (ESAF), and Firing Modules (FM) for safe fuzing requirements of both legacy and next-generation missiles and munitions. Our dedicated staff of research and design experts use the latest advances in technology to design smaller, lighter, and more cost effective ESAFs and FMs to meet evolving requirements of newer more sophisticated weapon systems. Capabilities include a line of components and subsystems that have been qualified for hard target penetration environments and next-generation smaller-class munitions.
-
product
Ultrasonic Thickness Guage
KM 130D
Kusam Electrical Industries Limited
Ultrasonic Thickness Guage is an intelligent hand held meter which adopts ultrasonic measuring principle, & is controlled by micro processor, provides quick & precise measurement of thickness for most of industrial material. This unit is widely used in various precise measurement for different hard ware / parts in industrial realm; one of its important application is to monitor the level of thickness-decreasing during operation of various & pressure container. Diffusely applied in manufacture fields, metal processing, and commercial inspection. The material that conduct & reflect constant sonic velocity, this product is to be applicable to used.
-
product
Hard Disc Drive Connectors
Teledyne Impulse provides a broad array of disc drive connectors. Our connectors are RoHS compliant and are being used on most major platforms around the world. Teledyne offers its cone point technology to insure maximum connectivity performance, and high temperature plastic materials are common. Teledyne's products are designed to meet the global requirements of the computing industry. Custom design configurations are available upon request.
-
product
Scan To CAD
Scanning or hard probing, large or small, we have a large arsenal of hardware & software to fit our clients’ needs. With all the reference data coming directly from the CAD model this eliminates any human error that would have come through manually entering nominal information.
-
product
GO-SCAN
3025
With their large active areas, shock-absorbing hard protective sleeves, and light-weight form factor, the new GO-SCAN digital panels have been designed to meet NDT technicians’requirements in terms of ease-of-use, ruggedness, and image quality.
-
product
Shore Durometer
UI-FT30
Shore Durometer is used to test hardness of rubber, thermoplastic elastomers, vulcanized rubber and other materials.
-
product
Leaking Current Meter
7610B
Peaceful Thriving Enterprise Co Ltd
This is a stable, low power consumption, and high accuracy 3 1/2 digits (2000 counts) leaking current tester for automobile. Leaking current for automobile is generally as small as milliamps, which is hard to measure by clamp meter. By plug this meter with the fuse box, user is able to measure leaking current as small as 1 mA.
-
product
Brinell Hardness Testers
Newage Testing Instruments, Inc.
We offer a wide range of rugged, high precision Brinell hardness testers and accessories for your Brinell testing.
