cPCI Digitizer
-
product
NON CONDUCT DIGITAL THERMOMETER
IBL-MT5
International Biological Laboratories
This Digital Non Contact type Infra Red Thermometer with laser sensor uses temperature sensor of Thermopile 6 - 14 mm and measures temperature from -50 to 550 Degree C and also in Fahrenheit scale.
-
product
Digital Gauge Counter
DG-5100
The DG-5100 is a high-resolution gauge counter having integrated structure. This counter achieves input frequency at 3 MHz which is high speed of ten times compared to conventional counter. (equivalent to a spindle velocity of 1.2 m/s at GS-3800B series)
-
product
Digital I/O
Curtiss-Wright Defense Solutions
Our digital I/O cards include interfaces to LVDS, Camera Link, Serial interfaces, and customizable I/O. Built leveraging our decades of experience producing highly rugged COTS signal acquisition hardware, our PMC and XMC modules are designed to perform reliably in the toughest operating environments.
-
product
PXI Digital Multimeters - DMM
All three PXI-DMMs deliver market-leading speed at their price points, measuring up to 15,000 readings/s with a maximum single-reading rate of 66 µs. These fast reading speeds translate into higher test system throughput and lower cost of test. Advanced triggering, enhanced functionality, and a full suite of free software simplify system integration and operation.
-
product
Digital Pulse Processor For X-Ray Spectroscopy
Dante
The Digital Pulse Processor for X-Ray Spectroscopy
-
product
Digital frequency counters
The instrument is equipped, in addition to the 20 Hz-160 MHz input, a second input for measurement up to 2.4 GHz with an impedance of 50 Ohms.
-
product
3U cPCI 8 Channel ARINC 429 Module
DP-cPCI-4296
DP-cPCI-4296 board features cPCI based eight channels ARINC429 protocol interface. As part of the cPCI family, the DP-cPCI-4296 board is fully compliant with compactPCI® specification 2.0 R3.0. and CompactPCI® Hot Swap Specification 2.1 R1.0.
-
product
Digital Dailysate Meter
Digital Dialysate Meter™ D4 & D6
The DIGITAL DIALYSATE METER is specifically designed to test both acetate and bicarbonate dialysate quality. Measure Conductivity, pH and Temperature to ensure proper mixing during dialysate preparation and as a final check of dialysate quality before hemodialysis treatment. There are no strips or reagents that expire or subjective interpretation of results. Internal sensors require the user to place the sample in the instrument, preventing contamination of dialysate by the measurement device.
-
product
Multicore Digital Signal Processor
SI-C667xDSP
Sheldon Instruments offers a complete portfolio of hardware products for a wide spectrum of real time applications in measurement and digital control systems. Our hardware range includes carrier boards that combine DSPs and FPGAs for various PCI/PCIExpress form factors such as slotted/desktop PCI/PCIe, PCI-104/PCIe-104, PMC/XMC, CompactPCI, as well as stand-alone embedded solutions. The DSP-FPGA carrier hardware is complemented by high performance analog and digital I/O modules as well as all necessary accessories like cables and terminal blocks.
-
product
5 1/2 Digital Bench Multimeter
VA82
Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD
12 different measurement functions: DCV/ACV, DCI/ACI, aa2W/aa4W, frequency/period, diode test, continuity, dB/dBm, etc.
-
product
Digital Impact Test Machine
The Digital Impact Testing Machine mainly used to determine the anti-impact capability and strengthen impact toughness of non metallic materials such as nylon, glass fiber reinforced plastic, ceramic & cast stone, electrical insulating materials etc.Sample and support are easy centeringThe pendulum of the machine can be raised or released automatically by button pressedDigital LCD screen control and value displayThe machine comply with GB / T1843, ISO 180, GB / T21189, GB / T2611 and other international standard
-
product
Digital Leeb Hardness Tester
TIME®5350
Beijing TIME High Technology Ltd.
TIME Group manufactured the first Leeb hardness tester in China in 1989 and has been the leading manufacturer of hardness testing equipment since then. Among all the TIME hardness testers, TIME®5350 is the best one with all the features. It looks like a mobile phone, easy to carry and makes a perfect tool for on-site hardness testing. Maximum 32GB MicroSD card can be used to store measured values.
-
product
Fixed Digital Gas Detector
OLCT 10N
Teledyne Gas & Flame Detection
The OLCT 10N is a digital combustible gas detector designed for to detect combustible, toxic gases or oxygen. Intended for use in combination with the MX 16, MX 32 and MX 43 controller, the OLCT 10N provides a fast and accurate response.All transmitter information is received by the controller in less than 1 second.Non-intrusive operator interface requires only a simple magnetic wand and allows one man calibration without opening the enclosure.
-
product
Digital Manometer
LEO Record (Ei)
KELLER AG für Druckmesstechnik
LEO Record is an autonomous battery powered instrument with digital display designed to record pressure and temperature over long periods. Both the piezoresistive LEO Record as well as the capacitive LEO Record (ideal for low pressure ranges) offer the following advantages:
-
product
mAEStro Audio Digital to Analog Converter
The mAEStro ADAC-100 receives AES/EBU (AES3) or S/PDIF digital audio and converts it to two channels of analog audio. It automatically detects sample rates up to 96kHz with low-jitter clock recovery. Two balanced line-level audio outputs are provided on XLR connectors on the rear panel. For convenient monitoring, a stereo headphone mini-jack and volume control are provided on the front panel.
-
product
USB Multifunction Digital I/O Module
Model JI-4040
The JI-4040 module is a versatile, easy-to-use device for adding universal digital I/O capability to acomputer system via a USB connection. The module is comprised of 36 bidirectional I/O channels and 2 Special Function Ports (SFP). The SFP can be software programmed as a variable duty-cycle clock/pulse generator, event counter, or interval/pulse timer. The I/O is selectable to interface 5.0 V, 3.3 V, 2.5 V, or 1.8 V systems. Host to module isolation eliminates ground-loops and provides protection from noise and switching transients on external signals. The JI-4040 is available as either a desktop unit or low-cost OEM board.
-
product
Digital Displacement Inductive Sensor
EX-V Series
High-speed, high-accuracy, digital inductive displacement sensors with sub-micron resolution and an ultra-fast 40,000 samples/sec. sampling rate. Automatic Bottom-dead-center measurement mode. High-speed sampling : 40,000 samples/second. Digital Inductive Displacement Sensor
-
product
cPCI 3U RB
Hartmann’s cPCI 3U RB Series Backplanes utilize a board design based on the HIGH-SPEED DESIGN concept. Low reflection is achieved by means of uniform signal surge impedance.
-
product
Dual Channel 180 MS/s Digitizer PXI / PXIe Card
GX2482
The GX2482 series are a high performance, dual differential channel, 16-bit digitizer offering high dynamic range and excellent SFDR. The module’s differential inputs, coupled with its low distortion makes it an ideal instrument for analyzing high performance or low level analog signals. Each channel offers 3 selectable low pass filters, a 16 bit, 180 MS/s ADC, and 64 M words of memory for each channel.
-
product
Digital Control DC Electronic Load
IT8200 Series
IT8200 series economical programmable electronic load,with the highest cost/performance ratio and small size, they are widely used in production testing lines and maintainance lines etc. Resolution 1mV/1mA ensures the accurate measurement result. IT8200 series has programmable performance, and can quickly recall 4 * 40 group memory data, panel function keys and display interface is clear, provide customers with simple operation program, easy and fast to complete a variety of complex tests. The series has CV, CC and CR mode, and short circuit test function, it is the most cost-effective electronic load products.
-
product
Digital IO
PA64IX
The PA64IX represents a new level of performance and capabilities for PXI-based digital instrumentation. Each card can function as a stand-alone digital subsystem or if required, multiple cards can be interconnected, supporting up to 1024 bi-directional pins (16 boards). The PA64IX also supports dee pattern memory by offering 32 M of on-board vector memory with static per pin direction control and with test rates up to 33 MHz.
-
product
Digital Multimeter
PT-30
Standard Electric Works Co., Ltd
● Lightweight, compact, and easy to use.● 4000 counts.● Full automatic measurement, voltage measurement, resistor measurement.● Data hold function.● Auto off function.● Continuity check.● Diode measurement.● Low battery indication.● Pen light provided.● Backlight LCD.● 3V DC power supply.
-
product
Digital Panel Meter
DPM
Digital panel meters are digital displays intended to be mounted in a panel, such as a control panel. They typically read some type of input, be it a voltage, current, or resistance, and display its value digitally. Often this input is a measurement from a sensor which is converted and displayed as a temperature, pressure, or other system variable. These meters may also act as simple controllers which trip a switch or perform a simple function when the reading reaches a preset measurement.
-
product
Digital I / O modules
The 34950A module has 64-bit bi-directional lines and can be configured with 8 8-bit digital I / O channels with handshaking capability. Each 8-bit channel has programmable polarity and a threshold of up to 5V. The memory can be used to generate or capture digital patterns up to 10 MHz. It provides seven configurable handshaking protocols for a wide range of applications. In addition, two counter / totalizer channels can be used to compute events, frequency, period, duty cycle, accumulation, and pulse width.
-
product
Digital Electrical Network Analyzer
4126 NA
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● 2 Lines × 16 Characters LCD.● Auto-ranging / Auto-off.● One Push Button Operation.● Low Consumption.● Better than 3% Accuracy(0.05-50Ω).● Wiring Integrity Check(display + LEDs).● Over temperature protection and indication.● Stores previous readings.
-
product
Digitizer
761 Family
The 761 is the family of CAEN Waveform Digitizer with the highest sampling rate Flash ADC (10 bit @ 4GS/s). It can record fast signals from fast organic, inorganic and liquid scintillators coupled to PMTs or Silicon Photomultipliers, Diamond detectors and others, and save them with high efficiency and precision for advanced timing analysis. The acquisition can be externally vetoed/gated. Multiple boards can be synchronized to build up complex systems.
-
product
Modbus Digital Input Output Modules
DAT3100 Series
The Datexel DAT3100 series is a range of Modbus digital input output modules. These cards or modules have the ability to accept digital voltage inputs and provide an output by the way of relays, NPN or PNP transistors. The DAT3100 devices can communicate with RS485 or RS232 on a Modbus or ASCII protocol making the DAT3100 series a very economical solution to large and small scale Data Acquisition. Combining these digital input output devices with the DAT9000 controllers and the DAT3000 analog input output modules make Datexel the smart choice where Data Acquisition is needed.
-
product
3 Digit LCD Voltmeter
DPM 600S
The DPM 600S is a 3 digit LCD voltmeter with 12.5mm (0.5") digit height. It features 200mV d.c. full scale reading, bandgap reference,auto-zero, auto-polarity and a set of annunciators. The meter can be panel mounted using the bezel and window. Connection to the meter is via solder pads.
-
product
Palm Size Digital Multimeter, Calibrated, 1999 Count, Mean Value, Manual Range, 3.5 Digit
72-7770 CAL
The 72-7770 CAL from Tenma is a palm sized digital multimeter with 3 3/4 digit LCD. It is 3 1/2digits with steady operations, fashionable design and highly reliable hand held measuring instrument. The meter measures AC/DC voltage, AC/DC current, resistance, temperature, diode and continuity. It is an ideal tool for maintenance. The multimeter features square wave output, data hold, low battery indicator and display backlight, This meter complies with the standards CE, IEC61010, in pollution degree 2, overvoltage category (CAT I 600V, CAT II 300V) and double insulation.
-
product
Digital Power Meter
2406B
‧Simultaneous display of W, A, V (PF or Hz)‧True RMS V, A, W‧Auto calibration via computer‧Data Hold∕Range Hold function‧Hight immunity to external noise‧CT ratio (1~99)‧REF function (0.800 ~ 1.200)‧Aux. power is AC 90 ~ 260V, 50/60Hz‧RS-232 interface (option)





























