cPCI Digitizer
-
product
NI-9775 , ±10 V, Up to 20 MS/s/ch, 14-Bit, 4-Channel C Series Digitizer Module
784539-01
The NI-9775 provides referenced single-ended analog inputs with two timing modes for applications such as fault detection in electrical transmission lines or structural failure events. You can use the NI-9775 to measure finite samples up to 20 MS/s/ch to capture fault detections or to measure continuously at up to 4 MS/s. You also can use the built-in analog reference trigger to assist with high speed phenomena. Additionally, the NI-9775 supports waveform streaming at a lower sample rate.
-
product
Ethernet/LXI digitzerNETBOX 14 Bit High Speed Digitizer - 500 MS/s on 2 Channels, 2 Single-Ended Inputs
DN2.445-02
The digitizerNETBOX DN2.44x series allows recording of one, two, four or eight synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
product
PCIe 8 Bit High Speed Digitizer - 1.25 GS/s on 2 Channels, 500 MHz Bandwidth
M4I.2211-X8
The 9 models of the M4i.22xx-x8 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
product
PCIe 16 Bit Multi-purpose Digitizer - up to 20 MS/s on 4 Channels (Single Ended) or 4 Channels (Differential)
M2P.5926-X4
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
product
Ethernet/LXI digitizerNETBOX 16 Bit High Speed Digitizer - 250 MS/s on 16 Channels, 16 Single-Ended Inputs
DN6.442-16
The digitizerNETBOX DN6.44x series allows recording of up to 24 synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
product
Ethernet/LXI hybridNETBOX 14 Bit Digitizer and 16 Bit AWG - 400 MS/s Digitizer on 2 Channels, 1.25 GS/s AWG on 2 Channels
DN2.828-02
The hybridNETBOX DN2.82x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 14/16 bit resolution and is available with digitizer sampling rates of up to 500 MS/s and AWG sampling rates of up to 1.25 GS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
-
product
PXIe Isolated Digitizer, 2-channels, 16-bit, 256 V, 32 Msa/Ch memory
M9217A
The M9217A PXIe digitizer is a single slot, 2 isolated input channels, supporting up to 256 V and sampling rate of 20 MSa/s and 16-bit resolution.
-
product
PCIe 8 Bit High Speed Digitizer - 2.5 GH/s on 2 Channels, 1.5 GHz Bandwidth
M4I.2221-X8
The 9 models of the M4i.22xx-x8 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
product
130/180 MS/s Dual Channel PXI Express Digitizer for Frequencies up to 175 MHz
PXIe-1803
This 130/180 MS/s Dual Channel PXI Express digitizer provides the best speed and performance available for input frequencies up to 175 MHz.With exceptional signal integrity, high density and modularity, and channel synchronization options, this new digitizer provides massive functionality in a compact form factor.Key features include:Dual 14/16-bit digitizer configurable as separate or fully synchronized channelsWaveform bandwidths of 65-175 MHz (typical)64M words of waveform memory per channelExternal clock input for synchronization up to 180 MHz250 μV Measurement AccuracyNoise Floor and RelativeAccuracy as Precise as 0.006%
-
product
Ethernet/LXI hybridNETBOX 14 Bit Digitizer and 16 Bit AWG - 400 MS/s Digitizer on 4 Channels, 625 GS/s AWG on 4 Channels
DN2.828-04
The hybridNETBOX DN2.82x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 14/16 bit resolution and is available with digitizer sampling rates of up to 500 MS/s and AWG sampling rates of up to 1.25 GS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
-
product
PXI-4065, 6½-Digit, ±300 V PXI Digital Multimeter
780011-01
6½-Digit, ±300 V PXI Digital Multimeter—The PXI‑4065 is a 6½‑digit, 300 V DMM, which makes AC/DC voltage, AC/DC current, and 2‑ or 4‑wire resistance measurements, as well as diode tests. It is ideally suited for OEMs, educational laboratories, or other cost-conscious test and measurement applications.
-
product
Multi-Channel 10-Bit Digitizer
ADQ8-8C
With compact modular form factors, 8 channels per board, and high-precision multi-board synchronization capabilities, ADQ8-8C is ideal for massive multi-channel implementations.
-
product
PCI-6512, 64-Channel, ±30 VDC, Source Outputs, Bank-Isolated Digital I/O Device
778968-01
The PCI-6512 is an industrial digital output interface, with eight banks of isolated channels. With programmable power-up states, you can configure the initial output states in software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6512 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
product
PCIe 8 Bit High Speed Digitizer - 1.25 GS/s on 1 Channel, 500 MHz Bandwidth
M4I.2210-X8
The 9 models of the M4i.22xx-x8 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
product
PXI Digital I/O Module With Power Distribution - With DC-DC Converter
40-228-001
The 40-228 provides 32 channels of digital input and 32channels of digital output, together with switched +12V,+5V, +3.3V and -12V supply outputs derived from the PXI backplane. The module is available fitted with a DC-DC converter (40-228-001) which provides an additional -5Vsupply output. Alternatively the module can be supplied with an industry standard footprint for a DC-DC converter(40-228-002) allowing the user to fit one of their own specification if required. The 40-228 includes a breadboard area that allows users to add their own circuitry to the module.
-
product
NI-9423, 24 V, 8 Channel (Sinking Input), 1 µs C Series Digital Module
783735-01
24 V, 8 Channel (Sinking Input), 1 µs C Series Digital Module - The NI‑9423 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with 24 V logic levels, can accept up to … 30 V discrete logic levels, and has an LED that indicates the status. The NI‑9423 offers isolation between the input and output banks from channel to earth ground. The NI‑9423 is a correlated digital module, so it can perform correlated measurements, triggering, and sychronization when installed in a CompactDAQ chassis.
-
product
6.5 Digit DMM / Digitizer PXI Card
GX2065
The GX2065 offers a unique combination of features, resolution, accuracy and speed in a compact, single slot 3U PXI format. Featuring 6- digit resolution, 0.005% basic DCV reading accuracy and up to 3,500 reading per second (rps) assures you of measurements that are accurate, fast and repeatable. All measurement functions including digitizing functions are isolated from the PXI bus - providing the ability to make true differential, floating measurements. An on-board controller performs all necessary DMM and digitizer calculations, minimizing PXI control bus overhead.
-
product
NI-9402, LVTTL, 4 Bidirectional Channels, 55 ns C Series Digital Module
779987-01
LVTTL, 4 Bidirectional Channels, 55 ns C Series Digital Module - The NI‑9402 is a per‑channel configurable digital I/O interface for input or output. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the NI‑9402 for … implementing custom, high-speed counter/timers; digital communication protocols; pulse generation; and more. Each channel features transient isolation between the I/O channels and the backplane.
-
product
NI-9423, 24 V, 8 Channel (Sinking Input), 1 µs C Series Digital Module
779009-01
24 V, 8 Channel (Sinking Input), 1 µs C Series Digital Module - The NI‑9423 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with 24 V logic levels, can accept up to 30 V discrete logic levels, and has an LED that indicates the status. The NI‑9423 offers isolation between the input and output banks from channel to earth ground. The NI‑9423 is a correlated digital module, so it can perform correlated measurements, triggering, and sychronization when installed in a CompactDAQ chassis.
-
product
PCIe-5764 , 16-Bit, 1 GS/s, 4-Channel PCI FlexRIO Digitizer Device
785962-01
The PCIe-5764 is a PCI FlexRIO Digitizer Device that simultaneously samples four channels at 1 GS/s with 16 bits of resolution and features 400 MHz of analog input bandwidth. With up to 70 dB of SNR, the PCIe-5764 is ideal for applications that require a wide dynamic range with a wideband digitizer.
-
product
SH68-68-D1, Shielded Cable, 5 m
183432-05
68-Pin, Female D-SUB to 68-Pin, Female D-SUB, Twisted Pair, Shielded Digital Cable - The SH68-68-D1 Digital Cable connects NI 6533/4 digital instruments and NI 660x or 661x counter/timer modules to 68-pin accessories. This shielded cable features twisted pairing and is offered in different lengths.
-
product
PCIe 16 Bit Multi-purpose Digitizer - up to 5 MS/s on 4 Channels (Single Ended) or 4 Channels (Differential)
M2P.5916-X4
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
product
64-Channel Boundary Scan Digital I/O Scan Module
JT 2111/MPV DIOS DIN
The JT 2111/MPV is a 64 channel boundary-scan digital I/O scan module enclosed in an impact resistant housing. The module is designed to test and control edge connectors, on-board connectors and logic clusters in boundary-scan applications. Multiple modules can be connected serially to increase the number of I/Os. Available with 96-pin DIN 41612 connectors and 20-pin 0.1″ pitch IDC connectors.This JT2111/MPV DIOS module is also available through our webshop.
-
product
PXIe Semi-Dynamic Digital I/O Module, 64-Channel
42-419-001
The 40-419-001 (PXI) and 42-419-001 (PXIe) are a 64-channel digital I/O modules suitable for operating external devices, such as power, RF and high voltage relays, solenoids and lamps. They can also be used for interfacing with external logic such as a programmable instrument with a BCD interface depending upon the module’s driving capabilities.
-
product
NI-9472, 24 V, 8-Channel (Sourcing Output), 100 µs C Series Digital Module
779004-02
24 V, 8-Channel (Sourcing Output), 100 µs C Series Digital Module - The NI‑9472 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with signals from 6 V to 30 V, features transient overvoltage protection between the output channels and the backplane, and has an LED that indicates the status.
-
product
High-Speed A/D 8-Bit Digitizers
GaGe 8-bit resolution digitizer models divide the input voltage range into 256 different digitization levels with sampling rates at up to 4 GigaSamples per second on 1 channel or 2 GigaSamples per second on 2 channels with input bandwidths of up to 1.5 GHz, deep onboard sample memory up to 16 GS (16 GB), and true ENOBs of up to 7.6 bits.
-
product
SH68-68-D1, Shielded Cable, 1 m
183432-01
68-Pin, Female D-SUB to 68-Pin, Female D-SUB, Twisted Pair, Shielded Digital Cable - The SH68-68-D1 Digital Cable connects NI 6533/4 digital instruments and NI 660x or 661x counter/timer modules to 68-pin accessories. This shielded cable features twisted pairing and is offered in different lengths.
-
product
Handheld Digital Multimeter, 4.5 Digit, Water and Dust Resistant
U1273A
Organic LED (OLED) display for high brightness level and wider viewing angles (up to 160 degrees)Features set that meet traditional industrial requirements and improve productivity and safety Improved accuracy and resolution to meet traditional industrial requirements (30,000 counts resolution with 0.6% for ACV accuracy)Intelligent features to improve productivity and safety (LPF, ZLOW, Smart )Better grip Visual and audible continuity indication in noisy environments Easy access to fuse for simplified maintenance Easy connectivity to PC and internal memory (up to 10,000) for data logging Large rotary switch and buttons that are easy to operate Dust and water resistant casing (IP 54 compliant)Compatible with U1177A/U1117A IR-Bluetooth adapter for remote monitoring & datalogging Altitude: 3000 meters
-
product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-purpose Digitizer - 125 MS/s on 24 Channels, 80 MS/s on 48 Channels, 48 Single-Ended Inputs, 24 True Differential Inputs
DN6.596-48
The digitizerNETBOX DN6.59x series allows recording of up to 48 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
product
NI-9437 , 24 VDC to 250 VDC, 8-Channel (Sinking Input), 1 µs C Series Digital Module
783737-01
24 VDC to 250 VDC, 8-Channel (Sinking Input), 1 µs C Series Digital Module - The NI‑9437 is well suited for direct connection in rail and power applications along with a wide array of industrial and automotive switches, transducers, and devices with high-voltage input needs. It features ratiometric thresholds that automatically adjust to 2/3 of the user supply voltage.
