PCI DAQ
Data Acquistion instruments configured to work in a PCI bus.
-
Product
PCI Express A/D Board
AD16-250 - Dual/Quad 16 bit, 250 MS/s
-
The AD16-250 series has two or four 250 MS/sec 16-bit ADCs, 8GB of on-board memory and the ability to transfer data directly into the host computer's memory at over 1 GB/sec. Streaming to the host computer can be performed simultaneously with acquisition to on-board memory, increasing the effective acquisition length by using the host computer's memory. Dual and quad channel boards sample concurrently at the input clock frequency, and can also be software selected to run in single channel mode, providing up to four (4) times the effective memory depth.
-
Product
4-port/8-port USB 3.0 PCI Express Card With 4 Independent Host Controllers
AX92321
-
*Four or eight USB 3.0 ports*Four independent USB 3.0 host controllers*900 mA/1500 mA max. per port configurable via jumper settings*Compliant with USB 3.0 Rev.1.0 and Intel® xHCI Rev.1.0*PCI Express x4 interface*Operating temperature from 0˚C to 70°C*Supports Windows® 7/10*Supports each port’s power on/off via software settings
-
Product
PCI GPIB Controller Card
Model 488-LPCI
-
* Adds GPIB Controller capability to any PC with a PCI bus.* Fast >1 Mbs transfer rate* 488.2V4 Driver supports 32 and 64-bit Windows XP, Vista, Windows 7, Windows 8 and Windows 10 with a true 64-bit DLL.* Driver compatible with industry standard 'ib' and '488.2' command sets.* Most affordable PCI-GPIB controller with a industry standard GPIB-32.dll.* Works with Agilent, NI and Kikisui VISA libraries.* ICS's Explorer auto configures your controller as it finds your instruments.* Use ICS's Explorer to control GPIB devices without having to write a program. * Program with Visual Basic, C, LabVIEW, Matlab or Agilent VEE* GPIB Card supports HP-IB Bus Systems.* Includes short bracket for lo-profile chassis.
-
Product
PCI Direct Digital Synthesizers
SYNTH300-TRIG-HS
-
These devices provide two synchronized DDS-based RF channels on a single PCI card. With fine frequency and phase control, triggered operation, and the ability to accept an external clock, the Synth300 products enable a number of advanced applications at a fraction of the cost of conventional equipment. In addition to two analog outputs, the product can be ordered with one (or two) LVDS outputs for programmable digital clock applications, and can be configured for control by externally supplied TTL signals for low-latency triggered operation such as PSK, FSK, and triggered sweep operation.
-
Product
ARINC 664 Part 7 Test & Simulation Interface for PCI Express
PCIe-C664-V2
-
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfaces - Simulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequencing & periodic data generated onboard - Error Injection including Runt Frames, Short IFG, and Invalid MAC FCSDevice driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
PCI Very High Density Multiplexer, 5-Channel, 32-Pole
50-670C-022-5/32
-
The 50-670C-022-5/32 is a 5-channel, 32-pole MUX and is part of a series of very high density multiplexer cards feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.The 50-670C shares exactly the same architecture as the established 40-670 range of PXI modules.
-
Product
PCIe-5763, 16-Bit, 500 MS/s, 4-Channel PCI FlexRIO Digitizer Device
786165-01
-
The PCIe-5763 is a PCI FlexRIO Digitizer Device that simultaneously samples four channels at 500 MS/s with 16 bits of resolution and features 225 MHz of analog input bandwidth. With over 73 dB of SNR, the PCIe-5763 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PCIe-5763 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
Product
(Compact PCI) GPIB Controller Card
Model 488-PXI
-
* Adds GPIB Controller capability to any PXI or Compact PCI System.* Fast >1 Mbs transfer rate* 488.2V4 Driver supports 32 and 64-bit Windows XP, Vista, Windows 7, 8 and Windows 10 with a true 64-bit DLL.* Compatible with industry standard 'ib' and '488.2' command sets.* Works with Agilent, NI and Kikisui VISA libraries.* ICS's Explorer auto configures your controller as it finds your instruments.* Program with Visual Basic, C, LabVIEW, Matlab or Agilent VEE* Most affordable PXI-GPIB controller card available.
-
Product
Squid Carrier Board™ Family PCI Express Carrier Board for 8 MiniPCI Express Modules
SKU-085-01
-
Squid PCI Express Carrier board for MiniPCIe modules is the first product in the Squid PCI Express Carrier Board™ family. PCI Express Carrier board was designed to expand modern motherboards that have PCI Express interface. It allows connection of up to 8 MiniPCI Express half or full-size MiniPCI Express modules to the one motherboard’s PCI Express slot.
-
Product
PCI 2 Amp Multiplexer, Quad 8-Channel, 1-Pole
50-635A-108
-
The 50-635A-108 is a quad 8-channel, 1-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PCI Module
PCI-1553-B
-
The PCI-1553-LXE/DXE 1,2 uses UTMC’s Sµmmit LXE/DXE version, UT69151DXE-GPC 1553 communication device as its 1553 bus controller, or remote terminal, or monitor terminal. A single controller has two redundant channels. The 1553board can have 1 or 2 communication channels. The controller accesses 64Kx16 word of external memory and has internal transceivers for both channel A and B. The 3U PCI board has on-board transformers for both channels and both controllers.
-
Product
PCI Daughter Boards
DB-24R/24 (24V)
-
The DB-24R consists of 24 form C, electromechanical relays for efficient switching of load by programmed control. The contact of each relay can control a 0.5 A /110 V load or 1A / 24VDC. The relay is energized by applying a 5 voltage signal to the appropriate relay channel on the 50-pin Opto-22 compatible connector or D-Sub 37 connector . Twenty-four enunciator LEDs, one for each relay, light when their associated relay is activated . This board needs a +12VDC or +24VDC external power supply to avoid overloading your PC’s power supply.
-
Product
PCI 64xSPDT Reed Relay Card
50-110A-121
-
This is the 64xSPDT version of our 50-110A/50-115A range of reed relay switching cards which are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female LFH connector.
-
Product
PCI 32xSPDT Reed Relay Card
50-110A-021
-
This is the 32xSPDT version of our 50-110A/50-115A range of reed relay switching cards which are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female LFH connector.
-
Product
ARINC 429 Multichannel Interface Card for Mini PCI Systems
DAS-429mPCI/RTx
-
The DAS-429mPCI/RTx is an ARINC 429, multichannel interface card for Mini PCI systems. The card’s small size and suitability for Mini PCI notebook computers, make them a complete solution for developing and testing ARINC 429 interfaces and for performing system simulation of the ARINC-429 bus, both in the lab and in the field.The DAS-429mPCI/RTx is supplied with C drivers, including source code and Mystic application program.
-
Product
IRIG Time Code Receiver for Computers (PCI Express)
TCR180PEX-EL
-
Meinberg Funkuhren GmbH & Co. KG
The TCR180PEX-EL receives IRIG-A/B/G, IEEE 1344, IEEE C37.118 or AFNOR NF S87-500 time codes and can be used for synchronizing the system time of its host PC. The IRIG output of this card can generate an IRIG signal for other IRIG time code readers. It is used in applications like data acquisition, standalone computer time synchronization (for systems without a network connection or higher accuracy requirements).
-
Product
PCI High Density Pecision Resistor Card, 9-Channel, 3Ω To 26.7kΩ
50-298-032
-
The 50-298-032 is a high density programmable resistor card with 9 channels which can be set between 3Ω and 26.7kΩ with 0.5Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI Reed Relay Card, 64xSPST
50-115B-121
-
The 50-115B-121 is a 64xSPST PCI general purpose switching card and is part of our 50-110B/50-115B range of reed relay switching cards which are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female LFH connector.
-
Product
PCI Express, Analyzer Software Included, IEEE 488 GPIB Instrument Control Device for Windows - Onboard GBIP Analyzer
780935-01
-
The PCIe‑GPIB+ combines an IEEE 488 controller and an analyzer on one device for computers with PCIe slots. You can use this device to integrate an instrument into your system using GPIB as well as to troubleshoot and solve GPIB hardware and software problems. The PCIe‑GPIB+ achieves maximum IEEE 488.2 transfer rates. With an onboard bus master DMA controller, there is no microprocessor interruption in data transfers. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
PCIe-5763, 16-Bit, 500 MS/s, 4-Channel PCI FlexRIO Digitizer Device
786168-01
-
The PCIe-5763 is a PCI FlexRIO Digitizer Device that simultaneously samples four channels at 500 MS/s with 16 bits of resolution and features 225 MHz of analog input bandwidth. With over 73 dB of SNR, the PCIe-5763 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PCIe-5763 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
Product
PCI Express Mini Card Adapter for PCIe Slots
PCIe-mPCIe
-
The PCIe-mPCIe Adapter is a practical solution for system developers when the target embedded system platform is not yet available, but our PCI Express mini card I/O board is, and you need to get started developing and testing the hardware and software.
-
Product
Compact PCI Multi-function Decommutator
LS-50-cP
-
The Lumistar LS-50-cP 3U Compact PCI Multi-function PCM Decommutator offers the greatest flexibility in the industry by incorporating up to 10 functions typically encountered in flight test applications in a single 3U Compact-PCI card slot. Five functions are achieved on the main board (PCM Simulator which can also operate as a BERT, PCM Decommutator, IRIG Time CodeReader, IRIG Time Code Generator, and the same 5 functions can be achieved on the LS-55-DB Multi-Function Decom Daughterboard. CVSD Voice Decoding and h.261 Video Decoding are achieved through software.
-
Product
PCI 2 Amp Multiplexer, Quad 8-Channel, 2-Pole
50-635A-009
-
The 50-635A-009 is a quad 8-channel, 2-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PCI Express 5.0 and Compute Express Link Protocol Exerciser
Summit Z516
-
The Summit Z516 is a PCIe 5.0 and CXL protocol traffic generation test tool used for critical test and verification intended to assist engineers in developing and improving the reliability of their systems. The Summit Z516 can emulate PCI Express 5.0 and CXL root complexes or device endpoints, allowing new designs to be tested against corner case issues.
-
Product
PCI 2 Amp Multiplexer, Single 64-Channel, 1-Pole
50-635A-001
-
The 50-635A-001 is a single 64-channel, 1-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PCI Express 5 CEM Receiver Test Automation
N5991PC5A
-
The N5991PC5A is the receiver test automation software for bit error ratio testers, allowing you to test, debug and characterize PCI Express 5.0 CEM Add-In Cards and systems.
-
Product
PCI-4065, 6½-Digit, ±300 V, PCI Digital Multimeter Device
779770-01
-
The PCI‑4065 makes AC/DC voltage, AC/DC current, and 2‑ or 4‑wire resistance measurements, as well as diode tests. It is ideally suited for OEMs, educational laboratories, or other cost-conscious test and measurement applications.
-
Product
ZIF PCI Test Connector
-
Meritec's ZIF PCI Test Connector offers the user an accurate and reliable way in which to test their PCI cards. With over 20,000 reliable cycles, it eliminates the need to constantly replace your PCI Connectors. Meritec's Test Connector assembly plugs directly into the PCI Connector in the test bed and is actuated by a lever for easy loading and unloading of cards. Meritec's solution eliminates the uncertainty associated with intermitancy between the PC Board and Test Connector during the test cycle.
-
Product
PCI Termination Products
-
Acromag provides a broad selection of hardware accessories to simplify the use of our I/O boards. This collection of panels, cables, and adapters facilitate field wiring and cable connections between boards within the card cage. Select from an assortment of cables and termination panels to simplify wiring and installation.
-
Product
16 SE Or 8 Diff. Input Channels, 8 Analog Output Channels, PCI Express
APCIE-3121-16-8
-
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
