Pneumatic
being of or for the use of pressurized gases.
-
Product
Right Angle Poppet Valve
PV10
-
We also offer a standard line of both cold traps and right angle poppet valves. Shown at left is a Bemco PV10 Right Angle Poppet Valve and a Bemco MCT12 Round Cold Trap. The cold traps and poppet valves are all stainless steel except for the pneumatic piston. They are available in ASA flange, Conflat, and weld mounting.
-
Product
Torque Sensors
-
To improve your product quality and lower your product loss rate, try Mountz torque sensors. Whether you need laboratory-grade precision to measure hand tool output in inch-ounces or the durability to handle frequent pneumatic tool testing in the foot-pound range, Mountz has the right torque sensor for your application. In-line rotary torque sensors even allow you to directly measure the torque a power tool applies to an actual fastener, giving you the most accurate measurement possible. Designed for ease of use, Mountz torque sensors are plug and play, helping technicians get right to work and minimizing the chance of error.
-
Product
24 Block Desktop Receiver
VGR24
Receiver
VG Mass Interconnect products provide a common Universal interface for your custom test rack and simplifies functional test across your product line. Mass interconnect bench-top and rack mount receiver Plug and play interface blocks for signal, coax, high current, pneumatic controls, and more Stable proven products with 25 years in service Best cost of ownership Fast delivery next day on key products! Compatible to currently available test instrumentation and platformsThere are a number of different block types: Coax up to 26 GHz Power up to 150 Amps Coax and power combined Signal: up to 170 pins, @250 VAC/5 Amps Pneumatic: up to 13 fittings Vacuum: port modules High speed: USB 3.0, HDMI, RJ45
-
Product
Tool Support Systems
-
New AIMCO FRLs--the supply of clean, dry air is essential to the operation of pneumatic tools. Ensure longer life with proper maintenance for your valuable tools. Ask about our extended warranty on Uryu tools.
-
Product
Pneumatic and Hydraulic Characteristics Test
-
Pneumatic and hydraulic testing is performed to demonstrate operating pressure, pressure drop, volume and flow parameters, as well as performance characteristics, of fluid system components and assemblies.
-
Product
10-CH Pneumatics CAN
YAV90PNE
CAN Interface
The YAV90PNE is a complete “plug & play” pneumatics subsystem controlled by CAN, for ATEs with Virginia Panel receiver. Thanks to this module, pneumatics actuators that are commonly used in the fixture side of an ATE, can be controlled. 10 3-way micro-valves are able to contorl 10 simple effect actuators or else 5 double effect ones. The module includes input for the position sensors. A pressure sensor is also included, so that the system air mains working pressure can be set between a minimum and a maximum.
-
Product
Regulators
-
Parker offers a range of air-line, pressure high flow and single phase regulators for instrumentation, filtration, refrigeration and pneumatic applications. Instrumentation regulators are used in the process, power, oil, gas and semiconductor industries to control the flow of liquids and gases with speed and precision. Air regulators provide quick response and accurate pressure regulation for the most demanding industrial air preparation applications, available as miniature, economy, compact, standard, hi-flow and pilot-operated regulators to meet a variety of service needs. The refrigeration line of pressure regulators includes valves that control inlet, outlet or differential pressure. Each regulator is available with an assortment of variations which enable one regulator to perform multiple functions. All regulators are built to the highest quality standards, recognized around the world for their performance, durability and reliability.
-
Product
MCB Thermal Trip Calibration Test Bench (IEC 60898 Cl 9.10.1.2, Annex I.1, IS)
-
The test system is designed and customized to carry out 2.55*Intest as per Table 7 (test c) of IEC 60898 (also mentioned for routine testing of MCBs. The test is done at dc current to exactly analyze and correct the bimetallic properties of the MCB as far as thermal tripping is concerned. The unit comes with a pneumatically operated test fixture with in-built dc stepper motor that is controlled by a micro controller / PC to calibrate the breaker into a narrow tripping band programmed by the user.
-
Product
In-Circuit Test Fixtures
-
Every type of in-circuit test fixtures (wired, wireless, pneumatic, vacuum) for all major tester brands.
-
-
Product
Portable Trace-Level O3 Calibrator
Model T753U
-
Teledyne Advanced Pollution Instrumentation
The Model T753U is a portable, microprocessor based precision Calibrator for Ozone gas instruments and sensors. Using a sophisticated Ozone generation system, combined with a sensitive photometer and pneumatic design, the T753U produces stable and reliable concentrations of Ozone in a convenient and rugged package based on our popular T750U Portable Multigas Calibrator platform. The T753U is housed in a high-density, molded travel case which includes an integral handle and wheels for durability and ease of use in the field for virtually any application. An internal zero air option extends the T753U's capabilities to also provide a clean and dry source of zero air, eliminating the need for a separate source of zero air. The internal zero air source module contains a software driven electronic inlet valve manifold allowing the calibrator to automatically switch between internal and external zero air sources depending on the application needs.
-
Product
Functional Fixtures
-
Joule''s strength is in the design and manufacture of functional test fixtures. Using 3D modeling software to create the fixtures allows us to actuate pneumatics, open and close overclamps, actuate side access units - all before a single part has been machined for the fixture.
-
Product
Topside Probing for Functional Test Fixtures
-
Circuit Check matches top side test targets to your specification and needs. The Signature Series pneumatic drive fixture is the industry standard for precision, accuracy and repeatability.
-
Product
Inductive Sensors (LVDT)
induSENSOR
-
Micro-Epsilon offers a large range of inductive sensors for displacement and position measurement from conventional LVDT sensors and inductive sensors with integrated controller to customer-specific high-volume versions. The induSENSOR displacement sensors from Micro-Epsilon are used in automated processes, quality assurance, test rigs, hydraulics, pneumatic cylinders and automotive engineering.
-
Product
Signal Pylon Blocks
-
40 POL low resistance pylon, 40 POL signal pylon, 85 POL signal pylon, 102 POL Signal Pylon, 136 POL signal pylon, 170 POL low resistance pylon, 170 POL signal pylon, high current pylon blocks, optical pylon blocks, pneumatic pylon blocks, radio-frequency pylon block, & usb pylon blocks
-
Product
Topside Probing In-Circuit Test Fixtures
-
Circuit Check matches top side test targets to your specification and needs. The Signature Series pneumatic drive fixture is the industry standard for precision, accuracy and repeatability.Today’s fifth generation Pneumatic drive supports as many as 8,000 test probes with centerline spacing to 25mil, and contacting test pads as small as 0.014″.
-
Product
Pneumatically Powered Bed of Nails Testers
Automator Pneumatic Family
-
Designed to provide factory assembly line conveyor based pneumatically actuated full test automation. Interchangeable pneumatics and manual lever options provide operation as a fully automated tester or as a manual bench top tester. These functional interchangeable options allow this fixture to grow with you as your production volumes increase. Test plate changeover is a quick 2 minute job. 4 thumbscrews to change the bottom plate and 4 SHC screws to change the top plate. The top plate drops down and slides out with the connector assembly. The bottom plate lifts up and out. The new plates slide back in. All rear panel connectors are mounted to the aluminum bracket on the top plate. This whole top plate assembly slides out together eliminating wiring hassles. Double sided access plate sets use transfer pins to get the signals from the bottom plate up to the top plate.
-
Product
Torque Verification
90229
-
SDI’s 90229 is designed for calibrating tools used to apply torque including electric and pneumatic power tools, torque sensors, hand and click wrenches. The strain gage based reaction torque sensors in the bench-mount housing remain stationary while torque is applied. The housing dis-assembles by removing two snap pins, allowing the user to easily change socket sizes and capacities.
-
Product
Mobile Testing Center
MTC-1500
-
The Mobile Testing Center (MTC) is a preassembled, above ground, mobile, testing solution designed for outdoor testing applications. An affordable option to permanent Test Cells, the MTC is comprised of 2 ISO containers. Container 1 includes a Test Cell and heated and air-conditioned Control Room. Container 2 is optional and includes facility support equipment: Bulk Fuel Storage, Pneumatic System, Water Recirculation System (WRS), etc.
-
Product
Fluid Power Actuators
CQ
-
The CQ range provides an innovative fully-concentric and balanced actuator design for quarter-turn valves. The design features a helical mechanism that transforms linear piston motion into quarter-turn valve stem rotation. CQ actuators provide a much higher torque output for a given footprint than scotch yoke designs typically utilised to operate many quarter-turn valve types. It is therefore ideally suited for installation in confined spaces. Further, Rotork’s unique helical pin design provides higher efficiency than a helical gear mechanism utilised by other valve actuator manufacturers.As standard, the CQ torque output profile, like that of a scotch yoke actuator, is engineered to parallel the torque demand profile typically found with popular quarter-turn valve types. The CQ design however is unique in that the torque profile can be custom engineered and manufactured to meet specific, non-standard valve torque requirements.In our experience, the CQ standard range of sizes is suitable for applications that require a pneumatically powered actuator with torque demand less than 150,000 Nm. However, we also engineer CQ actuators with greater output and/or hydraulic power. Please apply to Rotork for these applications.
-
Product
Fluid Power Actuators
LP/LH
-
Rotork linear actuators offer the advantages of compact size, high performance and a simple but highly reliable design. They are ideal for operating on/off and control functions of both globe and wedge gate valves. Both spring-return and double-acting configurations are available with either pneumatic or hydraulic cylinders.
-
Product
Flow Control Set Up Using PID Controller
ULP-25O & ULP-25T
-
Unitech Scales And Measurements Pvt. Ltd
Flow Control Setup Comprises of a Orifice with DPT to measure flow Rate. The flow of water is controlled by Control Valve with pneumatic actuator. I to P converter is provided to control the actuator. Rotameter is provided to measure actual flow rate. The system is mounted on a table top model with all necessary piping.
-
Product
Fluid Power Actuators
CP
-
CP range pneumatic actuators are a versatile, modular, scotch yoke design available in both double-acting and spring-return configurations. The compact and efficient design yields high torques even at low pressures. The design concepts found in Rotork's large, heavy-duty actuators has been applied to the CP range, which brings heavy-duty actuator qualities to small, quarter-turn actuators.
-
Product
Process Instruments
-
The use of clean, compressed air as a medium to operate, control, and transmit signals to pneumatic instruments like valves, transmitters, and controllers
-
Product
3/8" ID Contacts
Contact
VPC offers a range of pneumatic connectors that are ideal for use with automatic engagement interface systems. These pneumatic contacts also work well when used together with the VPC iDock Series.
-
Product
EZ-Slider Torque Arms
-
The EZ-Slider torque arm is crafted with a lightweight durable carbon fiber, the arm offers X & Y axis mobility. It provides the freedom to travel side-to-side and up & down on a production floor. An ideal ergonomic solution for multi-tool applications such as a moving production and assembly line where balancers are fixed to a trolley system. Eliminates torque reaction of assembly tools. Can be used with a variety of assembly tools like angle nutrunners and electric & pneumatic screwdrivers.
-
Product
Semiconductor
DieMark
-
DieMark Inking Systems are available in Electric and Pneumatic models and utilize convenient, disposable DieMark Ink Cartridges to streamline and optimize the process of marking defective die. With models available for nearly every test platform and configuration, Xandex inking systems are in operation daily in every corner of the world where wafer sort is performed.
-
Product
Compression Test Machines
-
Infinity Machine International Inc.
Compression Test Machines by Infinity Machine International Inc. - for applications such as: baby carriages and strollers durability tester, compressive strength testing machine, tensile testing machine, extrusion compression test equipment for small consumer electronics, paper bursting/crushing compressive strength testing machine, pneumatic springs compressive strength testing machine durability, and more.
-
Product
Actuator For EMC Tests
PSE-G-MC
-
Pneumatically operated actuator for operation of throttle on motorcycles and 2/3 wheelers. External set-point of the pedal actuator position via analog voltage to closed-loop pressure regulator in external valve box.
-
Product
Mini Contacts
-
VPC offers a range of pneumatic contacts that are ideal for use with automatic engagement interface systems. These pneumatic contacts also work well when used together with the VPC iDock Series.
