Drivers
translate general instructions into hardware specfic commands.
-
product
USB-6366, 8 AI (16-Bit, 2 MS/s), 2 AO (3.33 MS/s), 24 DIO USB Multifunction I/O Device
782262-01
8 AI (16-Bit, 2 MS/s), 2 AO (3.33 MS/s), 24 DIO USB Multifunction I/O Device - The USB-6366 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB-6366 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
product
ChenYang Voltage Sensors/Transducers
ChenYang Technologies GmbH & Co. KG
DC voltage sensor/transducer works according to Linear PhotoelectricalIsolation and is designed for applications to measurement and monitoring of DC voltage. Theoutput signal (DC voltage or current) of this transducer is proportional to the input DC voltage.They are suitable for measurements and long time monitoring of DC voltages and can applied topower supply management, DC motor drivers, battery chargers and systems etc.
-
product
PCIe-6323, PCI Express, 32 AI (16-Bit, 250 kS/s), 4 AO (900 kS/s), 48 DIO Multifunction I/O Device
781045-01
PCI Express, 32 AI (16-Bit, 250 kS/s), 4 AO (900 kS/s), 48 DIO Multifunction I/O Device - The PCIe‑6323 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. The device delivers high-performance functionality leveraging the high-throughput PCI Express bus and multicore-optimized driver and application software. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PCIe‑6323 is well-suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
product
PXI-6281, 16 AI (18-Bit, 625 kS/s), 2 AO, 24 DIO, PXI Hybrid, Multifunction I/O Module
779121-01
16 AI (18-Bit, 625 kS/s), 2 AO, 24 DIO, PXI Multifunction I/O Module—The PXI‑6281 offers analog input, correlated digital I/O, two 32‑bit counter/timers, and analog and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
product
PXIe-5186, 12.5 GS/s, 8-Bit Digitizer
782058-01
PXIe, 5 GHz, 12.5 GS/s, 8-Bit PXI Oscilloscope—The PXIe‑5186 high-speed PXI oscilloscope has two channels with flexible settings for coupling, voltage range, and filtering. PXI oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with fast signals that require up to 5 GHz of analog bandwidth and flexible measurement configurations. The PXIe‑5186 also features PXI synchronization and data streaming capabilities.
-
product
Ethernet-GPIB-USB to Modbus RTU Interface
Model 9009
* All interfaces provide full control of the Modbus RTU slave devices.* Ethernet port supports VXI-11, raw socket and Modbus TCP/IP to Modbus RTU conversion. * GPIB port works with any IEEE-488.2 compatible GPIB controller.* USB port uses Microsoft supplied driver to prevent operating system change problems.* The 9009 uses a simple command set that is accessible from any port.* Controllable with Windows PC programs like C, Visual Basic, LabVIEW, VEE, etc that make VISA or SICL calls. Works with Agilent, NI and Kikisui VISA libraries* Controllable from MAC/UNIX/LINUX and similar computers with RPC calls.* Ethernet interface protocol is fully VXI-11 compliant and does not require special PC drivers.* Internal webserver with sample Modbus device control pages for Watlow F4, F4T and EZ-Zone Controllers.* OEM oriented board designed for integration inside the user's system with only one cable. On board regulator works with 5 to 15 Vdc power.* Support programs Include ICS's VXI-11 and VISA keyboard control programs and a NTML page utility for uploading your customer webpages.
-
product
USB-6361, 16 AI (16-Bit, 2 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device
782255-01
16 AI (16-Bit, 2 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device - The USB-6361 offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB-6361 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
product
VXI PCI Express Crate Controller
V124
The V124 is a VXI bus master crate controller, usable as a crate slot 0 arbiter or as a secondary controller. Each PCI Express cable driver board, in a PC backplane, can drive one to four V124s over standard, flexible PCI Express cable assemblies up to 7 meters long.
-
product
PXI/PXIe 16-Channel Digital Output Module
40-412A-024
16-Channel Digital Output modules with high output voltage and current capability. The outputs can be used for high or low drive and each channel is capable of sourcing 0.5A from the high side or 0.5A sink on the low side. Accidental operation of both high and low side driver on the same channel is prevented by the supplied driver. Outputs are fully protected against over-voltage, over-current and thermal overload, ensuring robust and reliable operation in the toughest test environments. For high side driving, the voltage source is supplied externally, allowing the module to drive high capacity loads separate from the chassis power supply. For low side driving, the external source is not used and the module’s output operates an open collector or open drain driver.
-
product
Medical Workstations & Certified Medical PCs
CorMed-Q170 Medical Box PC The CorMed-Q170 Box PC is certified for medical use, fan-less, and rugged PC built to work with a variety of medical equipment and environments. This medical PC was expertly crafted for quiet yet powerful performance, with a 6th Generation Intel® Core processor. Additionally, the CorMed-Q170 is Energy Star 6.1 compliant, using less energy than comparable systems.CorMed-M24T Medical Computer The CorMed-M24T™ is an all-in-one medical computer, featuring a 24”, full high-definition display and 12th Generation Intel® processor. The CorMed-M24T™ is medically certified, touchscreen, antimicrobial, and available in a variety of sizes to accommodate your mobile, desktop, or medical cart application.CorMed-M24 Medical Workstation The CorMed-M24™ is an industrial touchscreen VESA-mount medical workstation, including 14 total I/O ports to ensure maximum connectivity. This medical workstation is designed for certification, and utilizes an Intel® Mobile Core i5/i3 processor.CorMed-M22 Medical PC The CorMed-M22™ is an industrial touchscreen medical PC. It features a 22” full high-definition widescreen with Intel® i7 CPU. With a 1000:1 contrast ratio, flat design, and 1920 x 1080 ppx resolution, the CorMed-M22™ is an excellent driver of growth and servicing capabilities.CorMed-M19 Medical PC The CorMed-M19™ touchscreen medical PC, featuring a 19” widescreen display, Intel® Core™ i7 processor, and 12 I/O ports for maximum connectivity and powerful monitoring capabilities.
-
product
Software
Battery Simulator
Chroma Systems Solutions, Inc.
Testing battery connected devices with an actual battery can either be cost or time prohibitive especially if multiple channels are required. Our Battery Simulation software is used to validate device functions during development in lieu of an actual battery or batteries. Automotive applications include motor drivers, OBC, DC-DC convertors or chargers, and products of DC bus.
-
product
PXIe-5785, 12-Bit, 6.4 GS/s, 2-Channel PXI FlexRIO IF Transceiver
785584-01
12-Bit, 6.4 GS/s, 2-Channel PXI FlexRIO IF Transceiver—The PXIe-5785 enables direct RF acquisition up to 6 GHz and generation up to 3 GHz with 12 bits of resolution. You can use it in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. The PXIe-5785 is ideal for applications that require wideband acquisition and generation with multichannel synchronization, including radar, electronic warfare, and communications. The FlexRIO driver includes support for acquiring and generating waveforms out of the box, and you can use the LabVIEW-programmable Xilinx Kintex UltraScale FPGA to implement custom algorithms for real-time signal processing.
-
product
Lens Driver Components
Analog Devices offers a range of lens driver solutions for camera modules in camera phones, camera enabled handsets, DSCs, consumer entertainment, and computer imaging. Lens drivers integrate drivers, waveform control, power management, signal processing, travel control, and more to provide the smallest, lowest power, most complete system solutions with the latest motor/actuator technologies.
-
product
Pulse Generation Measurement Board
MS 1806
*TTL Pulse measurement channels (Timers / Counters) 18 Channels*TTL Pulse Generation - 12 Channels*The Pulse Generation Frequency from 10Hz to 40MHz*The no. of pulses controlled from 1 to 255 pulses*All Channels are compatible with 5V TTL / CMOS*All the pulse input and the output signals driven through Pin Driver*Standard ISA Bus Interface*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
product
64 Ch Peak Sensing ADC
V1741
The V1741 is provided with drivers for the supported communication interfaces, C libraries, demo software for an easy board understanding. Firmware upgrade can be performed via optical link or VMEbus by the user.
-
product
PXIe-5122, 100 MHz, 100 MS/s, 14-Bit PXI Oscilloscope
779967-02
PXIe, 100 MHz, 100 MS/s, 14-Bit PXI Oscilloscope—The PXIe‑5122 high-resolution PXI oscilloscope has two channels with greater than 75 dBc spurious‑free dynamic range (SFDR) and flexible settings for coupling, impedance, voltage range, and filtering. PXI oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for both time-domain and frequency-domain applications that require high-resolution, low-noise measurements with up to 100 MS/s and 100 MHz of analog bandwidth. The PXIe‑5122 also features advanced PXI synchronization and data streaming capabilities.
-
product
POWER PROBE 4
PP401
*Electronic circuit and component tester that supplies battery ground and power along with 8 diagnostic testing modes to provide automotive technicians with detailed information on the circuits and signals being tested*Diagnostic Modes include: AC/DC Voltmeter, Ohmmeter, Frequency, Pulse width (Positive and Negative) Fuel Injector Tester, PCM/ECM Driver Tester and PPECT3000 Signal tracer*Tests for AC/DC voltage in 100ms and 50s resolutions, AC volts RMS and volts peak-to-peak, measure resistance, frequency and pulse width (negative and positive)
-
product
ARINC 664 Part 7 Test & Simulation Interface for PCI
PCI-C664-V2
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfacesSimulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequencing & periodic data generated onboardError Injection including Runt Frames, Short IFG, and Invalid MAC FCS - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
32-Ch SPDT 2A-240VAC 24VDC Switching
YAV90133
32 relays, 5A Switching 5A 250Vac. Up to 1250VA 28 Relays SPST Mux. 1 a 4 relays CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
Imaging Modules
Teledyne e2v has developed compact MIPI modules which feature our own high performance CMOS image sensors inside a pre-focused, industrial-grade scanning optic. As a turnkey sensor/optics for imaging systems, these modules offers customers significant reduction in development time and cost savings. Only a few screws are needed to mount the module, with simple connection to the image processing system through an FPC cable connector. Software development efforts can also be reduced by using some limited API-layer Linux software drivers. This enables the module to be seamlessly interfaced to popular ISP platforms.
-
product
GPIB-ENET/1000, Ethernet GPIB Instrument Control Device - Taiwan 110VAC
781630-11
The GPIB‑ENET/1000 is an IEEE 488 controller device for computers with an Ethernet port. You can use this device to share a single GPIB system among many networked users or to control several test systems from a single networked host. The GPIB‑ENET/1000 features a password-protected web interface for easy configuration. It can also control IEEE 488 devices from anywhere on an Ethernet‑based (LAN) TCP/IP network (Gigabit, 100BASE‑TX, 10BASE‑T). Each device interfaces to and shares up to 14 GPIB devices from several network hosts, and you can control up to 100 GPIB‑ENET/1000 interfaces with a single computer. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
product
Advanced Driver Assistance System (ADAS)
Cars have come a long way since they first came on the road in the 19th century. The first semiconductor-based noteworthy assistance was GPS-based car navigation systems toward the end of ´80s. Today, in almost every car, ABS (Anti-Lock Braking System) and ESP (Electronic Stability Program) are also contributing toward the driver and car passenger’s safety using high quality electronics. After all, the dreams of automated cars from the ´60s are now becoming true — it is only a matter of a few years.
-
product
Automatic Incident Detection
TrafiBot2
The FLIR TrafiBot2 is a compact, rugged camera solution for automatic incident detection. Combining full HD visual imaging with advanced video analytics, TrafiBot2's advanced processing generates traffic data and incident detection information for tunnels, bridges, and highways, including alerts on stopped vehicles, wrong-way drivers, and lost cargo.
-
product
PXIe-5172 PXI Oscilloscope, 100 MHz, 14 bits, 250 MS/s, 8 Channels, 1.5 GB, FPGA: Kintex-7 410T
784226-01
PXIe, 100 MHz, 4- or 8-Channel, 14-Bit, Kintex-7 325T or 410T FPGA Reconfigurable PXI Oscilloscope—The PXIe 5172 high-density PXI oscilloscope has eight simultaneously-sampled channels with flexible settings for coupling and voltage range. PXI oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with many channels that require up to 250 MS/s or 100 MHz of analog bandwidth and advanced PXI synchronization. The PXIe 5172 also features a programmable Kintex-7 325T or 410T FPGA that can be used for custom acquisition, triggering, signal processing, and data streaming.
-
product
RF / MW switch
The RF / MW switch includes a variety of RF and microwave switch modules - RF multiplexers, which are available for use in the 34980A multifunction switch / measurement unit, providing broadband switching from DC to 20GHz . Use these modules to route test signals between your device under test and a signal source, oscilloscope, spectrum analyzer, or other instrument. The switch / attenuator driver module also controls the external switches and attenuators of the 34980A.
-
product
Mixed Signal Test Systems
MTS1000i
The MTS-1000i is lowest cost platform available in the MTS series of ATE. It has a reduced platform size compared to the MTS-2010i & MTS-1020i, reduced power supplies, and 4 slots. It is mainly intended for single site testing. Like the other testers in the MTS family it is a highly cost effective production ATE designed for testing high-volume linear and mixed signal semiconductor devices (Op Amps, high-voltage drivers, DAC, ADC, etc.), both at the wafer sort and final test stages of the manufacturing process
-
product
Magnetrons and Accessories
Teledyne e2v is a leader in cargo scanning technology, delivering products that are integrated into 90% of major systems worldwide.Over 90% of the world’s non-bulk cargo is transported by ship in standardised containers. The containerisation system was developed after World War II and its cost reduction has been a major driver of international trade and globalisation. There are well over half a billion container shipments per annum.
-
product
PRO8 LD / TEC Drivers
This section includes single-channel laser current controllers, temperature controllers, and combined LD/TEC controllers compatible with our PRO800 and PRO8000 chassis.
-
product
PXI Bus Expanders
MXI-4E Series
The MXI-4E PXI Bus Expander allows for direct control of PXI systems from a PCI or PCIe slot in a desktop computer or server. MXI-4E interface cards can also be used for linking multiple PXI chassis. MXI-4E technology utilizes a high-bandwidth link that is transparent to software applications and drivers, therefore providing the ability to use high performance desktop computers or servers to control PXI systems.
-
product
Torque Tester
DIS-IPS series (20CL/5C)
For managing various torque wrenches, torque drivers, and automatic/semi-automatic machines. The highly compact detector is ideal for automated line measurements. Five channels of pass/fail judgment conditions can be saved, and settings can be made simply by switching channels even if the tightening conditions change. Efficient measurement is possible without unwinding work by "OW joint ".
