Debug
See Also: Debuggers
-
Product
Flying Lead Probes
FLP850
-
The PCIE850 provides a complete test and debug solution for PCI Express Bus. Interposers and probes connect to the PCIE850 providing access to PCI Card, AMX, XMC and VPX systems.
-
Product
Eclipse Test Development Environment
-
The Eclipse Test Development Environment automatically creates tests that are used to bring up new products in the lab. Failures can be quickly debugged using software tools such as the Eclipse Timing Diagram Analyzer and the Schematic Logic Probe.
-
Product
16 Channel 12C Relay Expansion
FXA-105 I2C Relay 16CH
-
The FXA-105 provides sixteen I2C controlled relays. It is equipped with a wide range 7V to 24V power supply and based on a 16bit I2C Port Expander (PCA9535). To simplify debugging each channel is equipped with a status led. In addition, it is delivered with an installed DIN rail carrier.
-
Product
In-Circuit Debugger for ColdFire V1
ICDCFV1
-
P&E's ICDCFV1 is a powerful tool for debugging code that supports Freescale's ColdFire V1 microcontrollers.
-
Product
In-Circuit Debugger for Power Architecture 55xx/56xx (Nexus)
ICDPPCNEXUS
-
P&E's ICDPPCNEXUS for Windows is a powerful tool for debugging code on a Freescale MPC55xx/56xx processor. The debugger comes with P&E's PROGPPCNEXUS flash programmer.
-
Product
ABex Rear Module for Direct Analog Bus Connection
ABex RM-RUBI
-
The ABex RM-RUBI is a rear module for the ABex system. It’s designed to connect instruments to the analog bus backplane from the back side of a chassis and to route signals for debugging purpose. Each of the 30 analog buses can be routed to one of the four 4 SMB-connectors.
-
Product
9 Pin Breakout Interface
VSI-Breakout-9
-
The VSI-Breakout-9 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
Product
DH Series High-Temperature Solder-In Tip, 16 GHz BW, 3.5 Vpp Range
DH-HITEMP
-
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
Telephone Line Monitor
AI-5120
-
The AI-5120 is a compact device designed for monitoring and analyzing signals present on the telephone line. By sensing the voltage present on the telephone line it detects and measures ringing, DTMF & pulse dialing, FSK (Bell 202 and V.23) signals, line polarity reversals, and open switching intervals (OSI). Working in conjunction with the TRsSim software on a PC, the AI-5120 becomes a valuable tool in analyzing and debugging Caller ID and SMS (Short Message Service) data transmission. Like an oscilloscope, it can capture and display waveforms showing various signals present on the telephone line.
-
Product
PCI Smart Bus Extenders
Live Insertion PCI Bus Extenders
-
The Ultraview PCIEXT64 extender series offers excellent PCI signal integrity, due to high speed trace layout, including high impedance signal traces and minimal ground inductance, as well as active bus isolation, to ensure minimal effect on the board-under-test. Power monitoring and current limiting features allow a robust debug and test environment. The capabilities of Ultraview's two models of Universal 66/33MHz 64/32-bit PCI extenders are as follows:
-
Product
Framework for Soft-Error Protection
RobustScan™
-
RobustScan™ provides a platform for users to pick patented Configurable Soft-Error Resilience (CSER) cells or their preferred SER mitigation cells. First, Soft-Error Rate (SER) analysis is performed. Then it performs automatic robust-scan-cell and hardenedcombinational- cell selection and synthesis. Finally it generates verification testbenches for the final design. RobustScan™ can be used with scan chains inserted using third-party tools; it can be linked to third-party�s SER analysis programs and is fully compatible with SynTest�s existing DFT tools for test, debug, and diagnosis.
-
Product
Protocol Analyzer
CY4500 EZ-PD
-
The CY4500 EZ-PD Protocol Analyzer records traffic passively on the Configuration Channel (CC) and allows users to analyze and debug USB Power Delivery communication. The low-cost and compact CY4500 acts as a pass-through for VBUS, VCONN, USB 3.1, USB 2.0 and USB-PD traffic. The EZ-PD Protocol Analyzer Installer includes a free Windows-based GUI (EZ-PD Analyzer Utility) that can be used to decode the USB-PD messages.
-
Product
PCIe Smart Bus Extenders
-
The PCIeEXT16HOT enables PCIe x16/x8/x4/x2/x1 boards to be rapidly tested, removed and swapped without having to reboot or power down the host system enabling rapid production testing and engineering debug. The hot insertion, current reporting, overcurrent indication and limiting and voltage margining capabilities make this board the highest performance PCIe bus extender in the industry.
-
Product
Debug Probes
J-Link and J-Trace
-
SEGGER Microcontroller GmbH & Co. KG
SEGGER J-Links are the most widely used line of debug probes available today. They've been proven for more than 10 years with over 250,000 units sold, including OEM versions and on-board solutions. This popularity stems from the unparalleled performance, extensive feature set, large number of supported CPUs, and compatibility with all popular development environments.
-
Product
USB Type-C Interconnects Compliance Test Software
S94USBCB
-
Use the S94USBCB software to test, debug and characterize your USB Type-C cable and connector designs. The PathWave TAP based test sequencer automates the network analyzer (VNA) for each test and generates a comprehensive HTML report. When run with L8990M switch matrix, it enables 20-ports fully automated test without port re-connection.
-
Product
AcroPack® I/O Modules
-
Acromag provides software support packages for embedded applications running on Linux®, Windows®, or VxWorks® operating systems. The libraries provide generic routines to handle reads, writes, interrupts, and other functions. Demonstration programs enable the developer to quickly exercise the I/O modules before attaching the routines to the application program. This diagnostic tool can save hours of troubleshooting and debugging.
-
Product
PCI-Express Live Insertion Extender
-
The PCIeEXT16HOT enables PCIe x16/x8/x4/x2/x1 boards to be rapidly tested, removed and swapped without having to reboot or power down the host system enabling rapid production testing and engineering debug. The hot insertion, current reporting, overcurrent indication and limiting and voltage margining capabilities make this board the highest performance PCIe bus extender in the industry.
-
Product
Test Research
TRI
-
REBOUNDER test kits feature two separate "Co-Active Seals", "Quick Twist" Locking Guide Pins, and boards constructed of fine weave G10/FR4, increasing testing reliability and accuracy while simplifying finishing, debugging, and maintenance. All H+W products are backed-up with our "Test-Assured" one year warranty, in writing, and SAME DAY SHIPMENTS
-
Product
Test & Measurement Equipment And RF Components
-
Is necessary for the design, test, manufacture, and debug of radio frequency devices.
-
Product
100 Pin Breakout Interface
VSI-Breakout-100
-
The VSI-Breakout-100 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
Product
cRIO-9048, 1.60 GHz Quad-Core CPU, 4 GB Storage, -40 °C to 70 °C, Kintex-7 70T FPGA, 8-Slot CompactRIO Controller
785621-02
Embedded Controller
The cRIO-9047 is a rugged, high-performance, customizable embedded controller that offers Intel Atom quad-core processing, NI-DAQmx support, and an SD card slot for … data-logging, embedded monitoring, and control. It includes a Kintex-7 70T FPGA with LabVIEW FPGA Module support for advanced control and coprocessing. The controller provides precise, synchronized timing and deterministic communications using Time Sensitive Networking (TSN), which is ideal for highly distributed measurements. This controller offers several connectivity ports, including Gigabit Ethernet, USB 3.1, USB 2.0, RS232, and RS485 ports. You can use the USB 3.1 ports to add a local human machine interface and program, deploy, and debug software, which simplifies application development.
-
Product
PCI Express 4 U.2 Receiver Test Automation
N5991PU4A
-
The N5991PU4A is the receiver test automation software for bit error ratio testers, allowing you to test, debug and characterize PCI Express U.2 devices and hosts at 8 GT/s.
-
Product
LXI Wired Trigger Bus Adaptors And Accessories
-
We manufacture LXI Wired Trigger Bus adaptors and accessories. These adaptors and accessories are designed to help debug a WTB system or provide conversion of signals to or from the WTB to products that do not support the WTB. LXI approved WTB cable assemblies and terminators are available to interconnect LXI devices that support the LXI Wired Trigger Bus extended function.
-
Product
File Import Tool For Importing And Converting STIL, WGL, VCD/EVCD, ATP Vectors
GtDio6x-FIT
-
Marvin Test Solutions' GtDio6x-FIT option offers test engineers a software tool set for importing and converting STIL, WGL, VDC/EVCD and ATP files to a Marvin Test Solutions' digital instrument file format. GtDio6x-FIT works in conjunction with Marvin Test Solutions' GtDio6x function library software which provides an efficient tool set for developing, debugging, and executing digital test vectors for MTS' GX5296 digital instrument.
-
Product
Function Test and In-Circuit Test
CT350
-
ICT test points: max 2736 CAD Data import Automatic program generator Powerful debugging tools Test coverage analysis Paperless repair station Logging- and statistic functions Full graphical functions Panel and multisite tests Fast adapter exchange High Pin Count-Interface On table optional usable shelf part.
-
Product
Digital Pattern Generators
DPG
-
Active Technologies Digital Pattern Generators also known as DPG, allow digital stimuli generation to stimulate digital designs, providing the capability to emulate standard serial or parallel bus transactions or custom digital interfaces, for system or device debugging and characterization.
-
Product
cRIO-9048, 1.30 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, -40 °C to 70 °C, Kintex-7 160T FPGA, 8-Slot CompactRIO Controller
785619-02
Embedded Controller
1.30 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, -40 °C to 70 °C, Kintex-7 160T FPGA, 8-Slot CompactRIO Controller - The cRIO-9048 is a rugged, high-performance, customizable embedded controller that offers Intel Atom dual-core processing, NI-DAQmx support, and an SD card slot for data-logging, embedded monitoring, and control. It includes a Kintex-7 160T FPGA with LabVIEW FPGA Module support for advanced control and coprocessing. The controller provides precise, synchronized timing and deterministic communications using Time Sensitive Networking (TSN), which is ideal for highly distributed measurements. This controller offers several connectivity ports, including Gigabit Ethernet, USB 3.1, USB 2.0, RS232, and RS485 ports. You can use the USB 3.1 ports to add a local human machine interface and program, deploy, and debug software, which simplifies application development.
-
Product
Mezzanine System
5047
System
The 5047 provides breakout of all ECM signals for debug, design validation and development. Plated through holes on the PCB allow soldering of probe wires to IO, Data, Power and Serial Identification signals. LEDs indicate presence of 3V, 5V, +12V, -12V and Ground. Elevates the ECM module by 2 mm and saves wear on the ECM carrier board connectors. Since this is a debug too there is no serial identification circuit.
-
Product
Media Analyzers
Vega Family
-
VEGA Media Analyzer (VMA) is an industry leading media analysis platform for standards compliance, debug, and interoperability of encoded streams. VMA enables navigation down to the deepest levels of a media file to generate error reports and analysis. This significantly reduces R&D and QA time in delivering standards-compliant video. VMA supports all popular video compression and container standards and includes features such as video comparison and quality checks. These features help deliver high quality, standards-compliant media while reducing R&D and QA time.
-
Product
PCI Express 5.0 Transmitter Electrical Performance Validation and Compliance Software
D9050PCIC
-
Use the PCIe 5.0 Tx compliance software to test, debug and characterize your PCIe Gen5 designs quickly and easily. It automatically configures the oscilloscope for each test and generates an informative HTML report upon test completion. The application compares the results with the specification test limit and includes margin analysis which indicates how closely the device passes or fails each test. With the option InfiniiSim Waveform Transformation Toolset, the software supports integrated de-embedding of the breakout channel of the test fixture.
