Battery Impedance
-
product
Precision Integrated Analog Front End, Controller, & PWM for Battery Test & Formation Systems
The AD8452 combines a precision analog front-end controller and switch mode power supply (SMPS), pulse-width modulator (PWM) driver into a single silicon platform for high volume battery testing and formation manufacturing. A precision instrumentation amplifier (in-amp) measures the battery charge/discharge current to better than ±0.1% accuracy, while an equally accurate difference amplifier measures the battery voltage. Internal laser trimmed resistor networks establish the in-amp and difference amplifier gains (66 V/V and 0.4 V/V, respectively), and stabilize the AD8452 performance across the rated operating temperature range.
-
product
Battery Capacity Analyzer
601B
The 601B Battery Capacity Analyzer addresses the need to test and maintain sealed lead acid (SLA) batteries used in backup power UPS, emergency lighting, fire alarms, security systems, and many other electrical systems. By quickly characterizing a battery's response to a load resistance and measuring the battery's internal resistance, this meter displays the remaining battery capacity as an indicator of the battery’s health. Powered by the battery under test, the 601B supports testing of both 6 V and 12 V storage type lead acid batteries.
-
product
Scienlab Battery Test System – Cell Level
SL113XA | SL100XA Series
The cell is the basis of any battery system and directly influences its function, performance and safety. Therefore, it is essential to test and characterize the cell at an early development stage. For this purpose, Keysight offers reliable test systems for precise and reproducible measurement results. The Cell Level Series (SL1002A, SL1004A, SL1007A, SL1132A and SL1133A) — also known as Battery Cell Tester — emulates sink and source for battery cells for automotive and industrial applications.
-
product
Battery Test Equipment
KV Hipot Power Test Equipment Co.,Ltd
Battery testers are the class of instruments designed to assess the condition—the charge, impedance, ripple current, or other measurement—of batteries to ensure they are working as required. Just as batteries have a very wide range of sizes and uses, so do battery testers.
-
product
Universal Battery Checker
T-333
Able to test 12 different sizes of rechargeable and non-rechargeable batteries.
-
product
Battery Probes
C.C.P. Contact Probes Co., LTD.
CCP offers a variety of different high current battery testing probes.
-
product
Murata Watch Battery
World's first mercury-free silver watch battery innovator, highly recognized as No. 1 market share manufacturer by major watch brands
-
product
5V50mA Coin Cell Battery Test Equipment
TOB-5V50mA
Xiamen Tob New Energy Technology Co., Ltd
8 Channels Battery Test Equipment (0.1-50mA, up to 5V) For Lithium Coin Cell Battery Research. TOB-5V50mA Battery Test Equipment is an eight-channel battery analyzer to analyze small coin cells with a range current 0-50mah, voltage 0-5v. Each channel of the analyzer has independent constant-current and constant-voltage source, which can be programmed and controlled by computer software.
-
product
Battery Testing Chambers
We supply a variety of test chambers for testing small battery cells to large lithium ion battery packs. Battery test chambers are supplied to a variety of industries including telecommunications, computer and automotive. With the goal of reducing automobile emissions and the development of electric vehicles, the need for lithium ion battery testing is even more critical. Our proven experience provides the most cost-effective solutions. Each test chamber is built according to specific test requirements and may be interfaced with battery cyclers, control & monitoring data acquisitions systems and other test equipment for a complete integrated test solution. All environmental chambers are designed with safety in mind. A variety of safety features are provided for reliability and abuse testing of batteries. These features may be incorporated into CSZ test chambers and tailored to the various hazard levels of EUCAR (European Council for Automotive R&D), a consortium of European car manufacturers. To better assess the hazard potential of tests, EUCAR has investigated hazardous situations and divided them into eight risk classes. The development of the safety equipment of our battery test systems is also based on this classification. For each hazard level, we recommend specific safety options that can be included with your chamber to meet your specifications to safety test your product. Together with our customers, we assess which safety devices are necessary for the respective test chambers.
-
product
Battery Pack ATS
8700
Chroma transfers its successful experience in 8000 ATS which is quite well-known in the power electronics industry to the battery application field by developing the Test Items specifically for the battery industry. It can perform automatic tests on the Battery Management System (BMS), semi products and finished products tests on the production line as well as provide long term maintenance and service to the battery module. 8000 (8700) ATS has flexible hardware architecture that can select a variety of hardware devices, such as DC Power Supply, Electronic Load, LCR Meter and 6 1/2 digits Meter, etc. to comply with different automatic testing requirements for various applications. In addition new hardware and test items can be expanded to meet the demands for inspecting the highly customized battery products with diversified tests. The capabilities supported are:
-
product
Battery Testing Chambers
ET-SERIES
These Chambers are designed and manufactured to meet various types of battery testing requirements of its customers by keeping all safety options in mind against any harmful explosions or ignitions and user safety while testing these batteries for environmental stress conditions
-
product
Scienlab Battery Test System – Pack Level, 220 KW
SL1730A
Keysight’s SL1700A Scienlab Battery Test System – Pack Level Series allows to realistically emulate the environment of the future battery pack application in order to test the high-power battery pack comprehensively and improve its functions and safety. The growing demand of e-mobility increases the need of vast battery test labs for EV battery development. Keysight developed the SL1700A Series to accelerate the development and validation of batteries. It offers a voltage range of up to 1500 V and power options between 100 and 300 kW including a Performance Bundle to increase the power up to 330 kW. The new high-voltage SiC (silicon carbide) technology provides a high energy efficiency on a small footprint and helps to minimize your operating costs.
-
product
Battery Tester 12V Language
BT12L
The Battery Tester 12V Language (BT12L) is an inexpensive, simple and easy tool for testing automotive batteries. It has LED display that consumes very little current and will not drain the battery with repeated testing.
-
product
Impedance Meter, Audio, 200Ω, 2KΩ and 20KΩ scales
72-6948
Active device is essential for reliable installation of background music and paging systems in residences, offices buildings and public areas. Avoid costly service calls and amplifier damage by verifying actual speaker system impedance prior to operation. Unlike conventional volt/ohm meters, which measure DC resistance, this unit utilizes an internal 1KHz oscillator to measure true impedance. Accurately measure speaker lines that utilize impedance matching volume controls, switchers, transformers and passive crossovers. Because this unit accurately measures up to 20Kohm, it may also be utilized with 25V, 50V, 70V, and 100V speaker line transformers in commercial installations.
-
product
Precision Impedance Analyzer (10Hz to 130MHz)
ST2851
ST2851 series precision impedance analyzer is a new generation impedance test instrument by adopting the current international advanced automatic balance bridge principle. It is based on Windows10 operating system, which realizes a fully computerized operation interface, making the measurement more intelligent and easier.ST2851 series impedance analyzer surpasses the 120MHz frequency bottleneck of similar foreign instruments, and solves the defect that it can only be analyzed but cannot be tested independently. At the same time, it adopts two interfaces of single test and analysis to make the test easier.
-
product
Battery Extra Load Units
BXL Series
BXL is an extra load unit designed to be used with DV Power’s BLU series battery testers. However, this unit is a universal add-on device. Because of that, it is compatible, as an additional load, with any other discharge/capacity tester in the market.In case when discharge current exceeds the capacity of a single BLU device, BXL can increase the discharge capacity. There are no limitations on the number of extra load units that can be connected in parallel to the main battery tester.A system of BLU and BXL instruments enables performing the capacity test in an accurate, user-friendly way. Also, all instruments are in accordance with battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.These units can be used on any type of battery string, such as lead-acid, Li-Ion, Ni-Cd, etc. They test battery strings with voltages in the range of 5,25 – 500 V DC. On the other hand, current up to 250 A can be discharged through the BXL internal structure.The instrument simulates a constant resistance load during the discharge test. Several resistances can be set for different battery nominal voltage levels. This makes BXL extremely flexible in selecting its load capabilities.
-
product
PXI/PXIe Battery Simulator Module, 6-Channel, 1 kV Isolation
43-752A-101
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
product
Battery Testing
Electric vehicles (EVs) rely on batteries as their primary source of energy storage. As battery packs require battery management systems (BMS) to operate safely and reliably, it is vital to test control algorithms for state of charge (SoC) estimation or cell balancing at an early stage.
-
product
Battery Analyzers
Beta D-50
*Analyzer for any type of battery.*Adjustable constant current discharge from 0 to 50 Amps.*Set for Amp-Hour capacity reading.*Accept or Fail lights Indicators for a GO/NO-GO Test.
-
product
Battery Pack BMS Test Equipment
WA-BMS-3NE
Xiamen WinAck Battery Technology Co., Ltd.
The battery BMS test system can be applied to the integrated test of 1S~100S power lithium-ionbattery pack BMS with LMU and BMCU modules, such as the BMS performance andHILL test.
-
product
Battery Load Tester
BT-100
Schumacher Electric Corporation
FOR EVERYDAY DIY USEEasy to operateTest load, battery condition, starter motor draw and complete charging system diagnosis.Works on 6 and 12 volt batteries50 amp load test for 6 volt batteries100 amp load test for 12 volt batteries Tests 6 and 12 volt batteries ─ up to 1000 CCATop-mounted rocker switch for easier operationSuper-grip, heavy-duty color-coded battery clampsEasy-to-read meter ─ accurate and shock resistantBaked enamel, steel case ─ ventilated to keep coolRubber insulated carrying handle ─ for comfort and safety
-
product
Battery Trickle charger
TCS-1
The TCS-1 Trickle Charger is a low current, constant current/constant voltage charger It can be used to trickle charge Nickel-Cadmium and Lead-Acid batteries. Its primary use is to maintain the batteries at full charge while the batteries are in storage (to compensate for the battery self-discharge). Adjustable float voltage and maximum charging current. Usable on batteries up to 100A-Hr The TCS-1 can also be used as a full charger for batteries of up to 5.0A-hr (@ C/10).
-
product
Digital, Hand-Held, Battery Operated Meter
CM-2
The Camera Master II is a digital, hand-held, battery operated meter that measures six different characteristics of any video signal. Use it for fast and accurate set-up of any video source.
-
product
Battery Discharger Charger Activator
KV Hipot Power Test Equipment Co.,Ltd
Battery Regeneration is a portable and compact tester which is used on discharging, charging and activating for disabling individual cell batteries.
-
product
Battery Capacity Testers|Discharge Testers
DV Power offers a wide range of battery capacity testers to meet specific customer needs. All of them are portable, powerful and most of all universal. Any battery string, such as lead-acid, lithium-ion, nickel-cadmium based and others, with voltages in the range of 0,9 – 800 V DC can be tested in an accurate, user-friendly way.The capacity test is carried out following the battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.BLU battery testers enable setting the discharge current up to 350 A, with 0,1 A resolution. If higher currents are required, several units can be connected in parallel, or BXL additional load units can be used. Discharge parameters can be monitored in real-time during the capacity test. Overall battery voltage, current, elapsed test time and capacity will be presented during the entire test on a touch screen display.
-
product
Battery Powered, Stand Alone Water Level and Temperature Data Logger
Level1000
The Level1000 is a rugged, submersible, battery powered, stand alone, water level and temperature data logger. Its stainless steel enclosure makes it perfect for use in lakes and streams. This is an all-in-one compact, portable, easy to use device that will measure and record data for up to 16,383 measurements.
-
-
product
MINI Battery Discharger & Capacity Tester
IDCE-4815CT
Fuzhou Fuguang Electronics Co., Ltd.
IDCE-4815CT can provide 0-150A (steps:1A) adjustable current for different test requests
-
product
5V30A High Current Lithium Battery Tester
TOB-BTS-5V30A
Xiamen Tob New Energy Technology Co., Ltd
8 Channels High Current Lithium Battery Tester For Power Battery Performance Detection
-
product
Battery Testing Systems
The CT2001 series Battery Testing Systems are designed for energy storage materials research and battery test. The eight channels are independently programmed and controlled by the computer. The Current ranges are from 1 mA to 5 A and Voltage ranges from 2V to 15V. Each testing system is specifically built for customer needs.
