Process Monitoring
-
product
Analog Input Products
Analog input boards are useful for measuring variably changing conditions in the real world. When we want to measure these variably changing conditions, we need analog inputs to convert these changing real world conditions to changing electrical quantities. For example, monitoring the temperature inside a wood kiln, or the water pressure on the output of a pump, or the heart rate of a medical patient. In each of these cases, you can use one of our analog input devices to convert the electrical data from a sensor or transducer into binary data that can then be used by your computer. The device that converts this data is known as an analog to digital converter (abbreviated ADC, A/D, or A to D). An analog input is a measurable electrical signal with a defined range. The analog input changes continuously in a definable manner in relation to the measured property. This data is very useful for process monitoring, process control, or simple monitoring / data collection and acquisition. ACCES' analog input boards amplify and multiplex input signals from thermocouples, strain gauges, accelerometers, photo sensors, flowmeters, RTDs, thermistors, voltage sources, millivolt sources, and current sources, just to name a few.
-
product
Magnet Testing
m-cat
m-cat is a magnetic field mapper for magnetrons which measures the magnetic stray field data of magnetrons on all three spatial axes and also calculates geometric data. This allows sputtering processes to be monitored and optimized, since the setting or status of the magnetron is critical to the subsequent outcome of the coating process.
-
product
Automated Thermostat Test System
*Transport mechanism moves thermostats to various temperature controlled locations.*Continuously monitored process status*PC controlled transport and measurements*Operator is shielded from 200 - 210 degree F hot water insertion baths*LabVIEW® test/process language
-
product
Firmware for High-speed Communication
OP-FW12GA
OP-FW12GA is the firmware to increase the speed of monitoring test of bit synchronous communication (such as HDLC/SDLC/X.25, or CC-Link communication), SPI communication, Profibus-DP (field bus known for high-speed communication), UART (asynchronous communication, which is commonly used). By processing great part of monitoring processes by FPGA, it unfailingly captures communication data with time stamps of a microsecond rate. The interface supports RS-232C/RS-422/RS-485/TTL.
-
product
100 amu CIS Analyzer
CIS100
Stanford Research Systems, Inc.
With better than 1 ppm detection limit, direct sampling at mTorr pressure, and a user-friendly Windows software package, the CIS systems will satisfy your most demanding applications. On-line process monitoring and control, verification of process gas purity at the point of use, high-vacuum residual gas analysis, and process equipment leak checking are some of the areas where these systems will prove indispensable
-
product
Software
Delphin offers a wide range of software solutions for data acquisition, displaying, archiving and analysis as well as process visualization and monitoring. Different product series, each with a different application focus, offer our customers the right solution for their individual measurement task.
-
product
Cameras
IRCameras is a subsidiary of Santa Barbara Infrared, a long-time leader in the design and manufacture of electro-optical (E-O) test instrumentation. SBIR, in turn, is part of HEICO Corporation, a technology-based aerospace company that’s been engaged in niche market segments within the aerospace, aviation and electronics industries for more than 40 years. Together we are uniquely positioned to advance development of thermal imaging technologies, and to commercialize these technologies for a wide range of applications including: nondestructive testing, predictive maintenance, online process monitoring and control, scientific research, target signature, security and surveillance and many more.
-
product
Analyzers of batteries
LLC "Megaron" develops and manufactures instruments for measuring parameters of various chemical current sources, devices for testing batteries. This equipment of varying complexity, from simple, designed for a specific battery, with the possibility to universal computer monitoring processes.
-
product
Area/process radiation monitoring
Monitors gamma and beta rays/ neutron with high accuracy and reliability. *Each monitor is controlled with central control system and alarm is given when the measurement exceeds alarm level. Area monitors and dust monitors.
-
product
Substrate Manufacturing
KLA’s substrate manufacturing portfolio includes defect inspection and review, metrology and data management systems that help substrate manufacturers manage quality throughout the wafer fabrication process. Specialized wafer inspection and review tools assess wafer surface quality and detect, count and bin defects during production and as a critical part of outgoing wafer qualification. Wafer geometry systems ensure the wafer shape is extremely flat and uniform in thickness, with precisely controlled wafer shape topography. Data analysis and management systems proactively identify substrate fabrication process excursions that can lead to yield loss. KLA’s substrate manufacturing systems support process development, production monitoring and final quality check of a broad range of substrate types and sizes including silicon, prime silicon, SOI, sapphire, glass, GaAs, SiC, GaN, InP, GaSb, Ge, LiTaO3, LiNBO3, and epitaxial wafers.
-
product
Computrac® MAX®
4000XL
The Computrac MAX® 4000XL provides quick, reliable and accurate results. This improves the ability to adjust or monitor processes, ensuring quality products while minimizing waste, energy requirements and man-hours. Ease of use and durability, along with superior service and support make the Computrac® MAX® 4000XL an ideal choice for research, manufacturing and laboratory environments.
-
product
FT-NIR Analyzer
ASP400 series
The TALYS ASP400 series analyzer is designed to achieve monitoring and control of continuous processes. Its seamless installation enables real-time process monitoring, determination of stream properties or physical qualities, process characterization and early troubleshooting. This analyzer is suitable for a wide range of refinery process monitoring applications including naphtha conversion units such as catalytic reforming, isomerization, naphtha hydro-treating and steam-cracking as well as applications in HF alkylation, gasoline blending and LPG.
-
product
Condition Monitoring
Is the process of monitoring a parameter of condition in machinery (vibration, temperature etc.), in order to identify a significant change which is indicative of a developing fault.
-
product
Wireless Sensor Tags & Interfaces
NFC and UHF RFID sensor tags offer a highly integrated solution for remote sensor data logging. The tags conform to the specifications of the NFC/ISO15693 as well as the UHF RFID standards. Featuring on-chip temperature sensing and the exclusive cool-Log™ technology, these sensor tags enable innovative and cost-sensitive solutions in food and pharmaceutical cold-chain management, industrial process control, remote monitoring and healthcare applications. NFiC™ ICs from ams lower the barriers to NFC integration in electronic devices thanks to their small footprint, high data rate, flexible data transfer modes, fully passive NFC tag emulation and advanced energy harvesting. NFC/HF interface tags are best suited to demanding consumer and industrial applications such as zero-power device configuration and set-up, feature-rich contactless cards for payment and authentication, smart toys and connected cars.
-
product
Thermal Machine Vision Camera
FLIR A615
The FLIR A615 is an easy-to-control, affordable, and compact thermal imaging camera for condition monitoring, process control/quality assurance, and fire prevention. This camera can be fully controlled by a PC, and is Plug and Play with third-party machine vision software such as National Instruments, Cognex, Matrox, MVtec, and Stemmer Imaging.
-
product
Ionic Contamination (Cleanliness) Tester
Zero-Ion
Current IPC standards now require ROSE testing for process monitoring. The Zero Ion ionic contamination tester fully complies with current IPC standards.
-
product
Mass Spectrometers Gas Analyzers
Our real-time Extrel quadrupole mass spectrometers are built for the demands of the gas and ion analysis for industrial and high purity process control, environmental monitoring, and cutting-edge laboratory research. Our mass spectrometers offer high sensitivity and a wide dynamic measurement range (ppb to %) for full, speciated composition. Our fast and powerful, quadrupole mass spectrometer performs precision quantitative analysis on every component in a gas or vapor mixture. It can easily be fully automated for sampling of multiple gas channels. For decades we have collaborated with research, academic, and industrial customers to deliver, design, integrate validate, and support these unique turnkey solutions.
-
product
Industry Products
China Sheenrun Electronics Co.
The forest fire prevention video monitoring and early warning management system is based on front-end monitoring equipment and video encoders, adopts a C/S architecture, and sends data and information to all areas in the service area through the network and other transmission links in the interactive area. Kind of server. The client in the business area manages and processes the monitoring business. The figure below is a schematic diagram of the system architecture.
-
product
32-CH/64-CH Isolated Digital I/O PCI Express Card With Digital Filter
AX92351
The AX92351 is a 64-ch isolated digital I/O PCI Express card with 2,000VDC isolation protection. This high-density digital I/O card with high-speed PCI Express x1 bus is excellent for use in applications requiring digital control or monitoring, such as semiconductor machinery, PC-based industrial machinery, programmable I/O logic control, and process status monitoring. The AX92351 features 32 isolated digital input channels and 32 isolated digital output channels with isolation protection of 2,000V for industrial applications where high-voltage isolation is required. It is equipped with a board ID feature for easy identification of multiple cards in single system. There is a digital filter function to prevent input signals from carrying noise or a chattering. Each isolated input has a sink or source current which supports dry and wet contact for maximum application flexibility. The card has a wide range of input voltage from 10 to 30V to meet most industrial application needs. The AX92351 also provides two interrupt sources on digital input channels. Digital output has open controller and supports maximum 30VDC. The read-back function is another useful function that allows monitoring each output port.
-
product
In-line Wet Process Concentration Monitoring
CI’s family of wet process concentration analyzers (WetSpec line) offers cost effective solutions for in-line wet chemistry monitoring. These products range from conductivity and NDIR solutions for simple chemistries concentration measurement, to spectroscopic systems for measuring multiple constituents and residues in complex solutions. The main concentration monitoring application that are served by CI Semi’s products are cleaning (SC1, SC2…) etching (HF, BOE, MAI….) and photo resist strippers (EKC, ACT, Piranha….).
-
product
Counters and Timers
Orbit Controls counters and timers are designed for connection to practically all industrial sensors and pulse sources . They can be used as process monitors to display the process variable to be measured or as process controllers for control and monitoring tasks. The devices display and process pulses and frequencies, as well as quadrature signals from incremental and absolute encoded rotary encoders. In addition to information on the display, the devices also generate data and analog outputs and monitor preselected limit values. The process parameters are entered via the keyboard so that the display is calibrated in the required units and the output signals, serial interfaces and limit values are optimized.
-
product
Carbon Compounds Analyzers
TML's Carbon compound analyzers utilize Gas Filter Correlation combined with reliable NDIR (non-dispersed infrared) technology to produce very stable and accurate gas measurements. All T Series analyzers offer two front-panel USB ports, an advanced touch screen full color display, customizable user interface with predictive maintenance alerts, one-touch real-time graphing, and multiple language support. All of our analyzers are designed meet the rigorous demands of ambient air quality, stack, or industrial process gas monitoring.
-
product
SpectraTrend HT
Hunter Associates Laboratory, Inc.
SpectraTrend HT supports implementation of today’s Total Quality Management programs such as LQM, PAT, Six Sigma, DMAIC, and others that share a common goal of producing consistent product quality and reducing waste. SpectraTrend HT utilization can facilitate continuous monitoring of product Height to enhance Good Manufacturing Practices (GMPs) within their enterprise, reduce risk of color quality variation and associated costs through real-time process color monitoring and enhance consistency and predictability of their quality assurance approach.
-
product
Nuclear Power Radiation Monitoring Systems
From continuous area monitors, radiation detectors, process monitors and remote indicators and alarms, featuring industry-standard technology, Victoreen instruments are the trusted source for radiation monitoring systems and quality assurance for nuclear power professionals. With a wide range of solutions for maintaining Code of Federal Regulations-compliant facilities, Victoreen delivers the safety, reliability and quality needed to guarantee top performance for the global atomic energy community.
-
product
Process Control Instruments
burster präzisionsmeßtechnik gmbh
Measuring accuracy of up to 0.05 %, sampling rate 10 kHz maximal, innovative evaluation elements, i.e. windows, thresholds, trapeziums, envelope curves, freely definable mathematical operations, two synchronous processes can be monitored, 128 measuring programms, intelligent Signal sampling, programmable I/O functions, Ethernet, USB, RS232, extensive diagnostics and statistical analysis, all usual sensor interfaces, variable fieldbus interfaces, powerful PC Software
-
product
Seismic Impact Control System
ZET 048
Seismic impact control system is used to control ground surface shifts caused by earthquakes, explosions and other natural or technology-related factors. Seismic control system is used to obtain actual information of the seismic environment as well as for process facilities state monitoring (in particular, for petroleum industry pipelines systems control).
-
product
High Accuracy Dimensional Metrology System
Pinnacle 250
The Pinnacle features a damped granite base and column, with passive vibration isolation. A precision compound X-Y stage with high-speed linear motor drives provides velocity of 400 mm / sec and acceleration of 1000 mm / sec2. This combination of high acceleration and high velocity enables the high throughput required for near-line process monitoring.
-
product
Dissolved Ozone Instruments
Teledyne Advanced Pollution Instrumentation
For measuring dissolved ozone concentrations in water a microprocessor controlled instrument can be used for automatic and continuous measurement by means of an disinfectant sensor. All of our instruments are designed meet the rigorous demands of ambient air quality, stack, or industrial process gas monitoring.
-
product
Sulfur Compounds Analyzers
TML's Sulfur compound analyzers utilize familiar UV Fluorescence technology to produce reliable and accurate gas measurements. All T Series analyzers offer two front-panel USB ports, an advanced touch screen full color display, customizable user interface with predictive maintenance alerts, one-touch real-time graphing, and multiple language support. All of our analyzers are designed meet the rigorous demands of ambient air quality, stack, or industrial process gas monitoring.
-
product
ESD Event Detector
Novx MiniPulse
Simco-Ion's Novx MiniPulse ESD Event Detector is designed for tool and process monitoring. This affordable, small footprint embeddable monitor has been developed to warn of product damage risks at the point of electrostatic discharge. The MiniPulse uses time domain and threshold discrimination to detect pulse electromagnetic energy. Through the use of specific antenna configurations and placement, the MiniPulse can provide ESD event detection for well-defined small areas.





























