Fiber Modems
-
Product
FOCL Reference Signal Modem
VCH-607
-
FOCL reference signal modem VCH-607 is designed to receive and transmit electrical signals with a nominal frequency of 100 MHz through a fiber-optic system and generate electrical signals with a nominal frequency of 5 and 10 MHz, coherent with the input signal. Reception and transmission through the FOCL is provided using a pair of modems: one is configured as a Transmitter and is installed at the end of the FOCL where the signal source is located, the second is configured as a Receiver and is installed at the opposite end of the FOCL.
-
Product
MODEM SHARING DEVICES
-
The Modem Sharing Devices are designed to allow RS-232 DTE (terminal) devices to share Leased Line and Dial line Modems or DSU's. Data arriving at the Master Port is continually broadcast to all Subchannels. The attached terminal device that raises the RTS control signal is automatically given control of the MSD. Data rates of up to 128 Kbps are supported.
-
Product
Fiber Optics
GEN II FOB
-
Fiber Optic converters Electrically isolate signals from the vehicle bus using common bridge and satellite modules interconnected with fiber optic cable for EMI and EMC testing.
-
Product
Fiber Inspection & Cleaning
-
ShinewayTech Fiber Inspection & Cleaning - Optical Connector Inspector, Wireless FIber Inspection Probe, Cleaning Pen, & more.
-
Product
Fiber Identifier
OFI-20A
-
OFI-20A can detect optical signal presence, type and direction anywhere on fibers during optical network deployment, maintenance and troubleshooting. With non-destructive macro-bend detection technology, it introduces no damage to tested fiber or interference to the service on fiber. OFI-20A is able to identify wide-spectrum signals (such as signals in CATV system) and can be used in SONET/SDH & DWDM systems tests.
-
Product
Fiber Optics
-
The use of fiber optics as light guidance allows great modularity and flexibility in the setup of an optical measurement system. Optical fibers can be made of many materials, such as plastic, glass, and silicates (SiO2). For high-quality fibre optics, as used in spectroscopic applications, synthetic fused silica (amorphous silicon dioxide) is used, which can be intentionally doped with trace elements to adjust the optical properties of the glass.
-
Product
Ground-Based Satcom Amplifiers, Modems & More
-
Modems for Small-to-Medium Sized Networks Where Security is of Utmost Importance.
-
Product
Optical Fiber
10 Gbps SFP+
-
Are designed for 10 Gbps serialoptical interfaces for data communications with multimode fiber (MMF).
-
Product
Fiber Lab Flex
-
The Fiber Lab Flex from M2 Optics is a unique platform designed to offer engineers with maximum versatility when requiring optical fiber spools for network simulation, latency, training, and other testing and networking applications.
-
Product
Digital Fiber Sensor
FX-410
-
Panasonic Industrial Devices Sales Company of America
This dual display digital Fiber Sensor is unique with its manual threshold value setting. Just "Look" and "Turn" simple, easy-to-use Fiber amplifier. The incident light intensity and threshold values can be checked at the same time with operation needed. In addition, no complex mode settings are needed when the values are adjusted.
-
Product
Live Fiber Identifiers
-
Wuhan Sunma Technology Co., Ltd.
Live Fiber Identifier are essential installation and maintenance instrument in data networks, CATV and telecommunication networks. Fiber identifier can identify the optical fiber by detecting the optical signals transmitted through the cables. SunmaFiber supply different types of Fiber Identifiers and Talk Set to meet you requirement, and they are with rechargeable battery and power supply adapter, so you can use them easily.
-
Product
Fiber Analyzers
-
Fiber analyzers for extraction and analysis of plant, feed, food and other agricultural products. Used in the determination crude fiber, neutral detergent fiber, acid detergent fiber, hemicellulose and acid detergent lignin.
-
Product
Modem
CDA-RES
-
Hitron Americas Technologies Inc.
The CDA-RES is a DOCSIS 3.0 solution providing the perfect choice for cable operators who want to offer high-speed broadband access to their customer base economically. It delivers speeds of up to 320Mbps (8×4) with eight bonded downstream channels over its DOCSIS interface – eight times faster than a conventional single-channel DOCSIS 2.0 cable modem! The integrated Gigabit Ethernet port enables easy home networking.
-
Product
Fiber Inspection and Cleaning
-
Dust - just because you can't see it doesn't mean it's not there. A 1-micrometer dust particle on a single-mode core can block up to 1% of the light (a 0.05dB loss). The only way to know it's clean is to inspect it before you connect it. And if it's dirty, it needs to be cleaned with the right tools or you might just make it worse. Know it's clean with our cleaning and inspection tools.
-
Product
Optical Fibers and Modules
-
Optical fibers are at the heart of everything we do. We embed as many functions as possible directly into the fibers to make systems based on our fibers simpler, cheaper, and more reliable.
-
Product
Launch Fiber Box
-
OTDR measuring devices are used in various ways in fibre optic technology. They enable extensive characterisation of existing fibre optic cabling networks. The use of launch and receive fibres is advantageous when it comes to ensuring precise results evaluations. With bidirectional backscatter measurements with launch and receive fibres, the attenuation values of the first and last plug-in connection can be determined precisely by averaging and device dead zones can be avoided. Measuring device manufacturers recommend different lengths of launch and receives fibres to avoid “phantom reflections”. These launch and receive fibres are also subject to measuring equipment monitoring and should regularly undergo revision in accordance with the OTDR measuring devices. A good measurement result depends on the state and quality of the measuring equipment used. Diamond offers various types of launch and receive fibres, one with standard telecommunications connectors and the other with an outdoor connector for harsh environments.
-
Product
Fiber Splice Closures
-
Wuhan Sunma Technology Co., Ltd.
Fiber Optic Splice Closure is a fiber management product typically used with outdoor fiber optical cables. It provides space and protection for the fiber optic cable splicing and joint. Fiber splice closure is used for aerial, strand-mount FTTH "tap" locations where drop cables are spliced to distribution cables. SunmaFiber supplies two types of fiber splice closures which are the horizontal (inline) type and the vertical (dome) type. Both are made of excellent engineering plastics to be waterproof and dust proof. And with various ports types, they can fit different fiber optic core numbers. More details about splice closure.
-
Product
Acoustic Modem Option for Control Module
-
Gavia AUVs can be fitted with the Teledyne Benthos ATM-900 Acoustic Modem. The ATM-900 Series Acoustic Telemetry Modem is the most advanced, multipath and noise tolerant, modem available. They are designed to meet both the high data rate requirements of commercial users, and the higher reliability, lower data rate requirements of the military. The modems employ two modulation techniques: phase shift keying (PSK), which provides the highest bit rate, and multiple frequency shift keying (MFSK), which provides reliability in a multipath environment, or when the modems are required to operate in a low signal-to-noise (SNR) environment. The ATM-910 Series can transmit data using PSK modulation for reception by a Gavia Modem Deckbox, but receives data using MFSK modulation only. MFSK modulation is a spread spectrum modulation process that transmits multiple tones simultaneously.
-
Product
Fiber Sensors
-
Easy to install.Numeric displays, interactive prompts.Applications focus on many industries,such as semiconductor assembly, handling technology and packing.Depends on the mounting direction, the digital display of BR1 can be inverted.Response time selectable:(20050010005000)s.
-
Product
Fiber Optic Terminus
ARINC 801
-
The ARINC 801 fiber optic terminus is the next generation of high density, butt joint interconnect technology. With its standard 1.25 mm ferrule and sleeve, the ARINC 801 terminus is designed for both multimode and single-mode applications. For the pull-proof design, the cable jacket is crimped on an external body and a floating mechanism avoids any loss of performance when pulling on the cable. This feature allows for the use of the connector without a backshell. Standard connector formats include MIL-DTL-38999 type, MIL-DTL-83527 type, ARINC 600 and ARINC 781.
-
Product
Fiber Preparation
-
When it comes to fiber preparation, PK’s fiber cleaver tools are widely regarded as the best on the market—especially when it comes to low-loss high-strength fusion splicing applications.
-
Product
Fiber Identifier & VFL
-
Are designed to non-invasively identify continuous-wave signals in fiber optic cables. They are low cost, hand-held tools.
-
Product
Fiber Inspection Probe
FIP-920
-
FIP-920 Fiber Optic Inspection Probe combines a 3.5” high definition TFT LCD display, provides a detailed image of fiber end-face, zoom in/out feature make it easy to identify the smallest particles, scratches. With the attached SD card memory, you can capture/record the live end-face image, the image file can be reviewed/transferred via SD card reader or USB cable. Up to 8hrs battery working make it possible to inspect the fiber end-face at any time and any place.
-
Product
Bare Fiber Aligner
1120
-
The Photon Kinetics 1120 Bare Fiber Aligner makes it possible to reduce test setup time to seconds, thereby reducing overall testing cost. Just strip the fiber, scribe and break it (or use a more precise fiber cleaver, if desired) and then insert the prepared end into the 1120. In an instant, the fiber is coupled to your OTDR or chromatic dispersion test system with low optical loss and low reflectance. The 1120's compact, ergonomic industrial design is well-suited for low to moderate volume fiber and cable testing applications where automated fiber alignment systems are less economical. It is particularly useful as part of an in-process or finished cable test station employing either the 8000i or 8000 OTDR, and the OASYS.net OTDR Automation Software.
-
Product
Optical Fiber Identifier
FID-30R/ 31R
-
Shanghai Fibretool Technology Co.,Ltd.
FID-30R and FID-31R are optical fiber identifier for telecommunication cable. FID-30R is built-in optical power meter.
-
Product
Fiber Containment Vaults
-
Switchblade is an innovative fiber containment vault with a folding design that reduces shipping cost, storage space footprint and increases productivity and speed to market. The flared design maintains a best-in-class strength to weight ratio – minimizing the effects of frost heave, while optimizing internal volume.
-
Product
Digital Fiber Sensor
FX-550
-
Panasonic Industrial Devices Sales Company of America
The FX-550 Digital Fiber Sensor or Fiber Optic Amplifier has three times higher emission power and 1.6 times longer sensing range than conventional models. Higher incident light intensity results in more stable detection and easy beam axis adjustment.
-
Product
Optical Fiber Tensile Jig
-
This jig is designed for tensile testing optical fibers and other brittle fibers. The jig consists of upper and lower pneumatic flat grips with flat grip faces followed by large-diameter capstans.
-
Product
Fiber Optic Pressure Sensors
-
Opsens Solutions optical pressure sensor delivers reliable results in harsh environment. Opsens Solutions OPP series fiber optic pressure transducers are designed to provide accurate pressure measurement in the most adverse conditions. Its small size and EMI/RFI/MRI immunity makes it the ideal sensor for industrial applications.
-
Product
Fiber Pigtailed Tapered Amplifier
-
The AOSense tapered amplifier (TA) provides a coherent high-power beam, inheriting all properties from the seed source. TA’s are an essential optical component for quantum sciences, such as laser cooling and trapping, cold atom sensors, electromagnetically induced transparency, and quantum spectroscopy. The TA is also used in commercial laser modules, including master oscillator power amplifier (MOPA) lasers and external cavity lasers.
