Ethernet Testers
-
Product
IP / Ethernet Testers
-
Anritsu's powerful Ethernet/IP network data analyzers incorporate the dual functionality of wire speed performance analysis and network monitoring in the same instrument. Multiple protocols can be decoded and displayed for captured Ethernet, SONET, or SDH frames at full wire speed up to 100 Gbps, augmented by an optional Decode Module and Expert Analysis Module.
-
-
Product
SDH Ethernet Testers
-
Wuhan Sunma Technology Co., Ltd.
The SunmaFiber SDH & Ethernet is easy to use, cost effective Ethernet testing solution for basic physical layer cable testing, layer 2 and layer 3 traffic generation, and full RFC 2544 testing. The rugged, battery operated, application specific test tool enables field technicians to turn-up Ethernet and IP services by running an RFC 2544 test or following a set of methods and procedures. The product has been designed for front-line technicians who do not have experience dealing with emerging Metro Ethernet technologies and need a simple to use solution for Ethernet and IP testing.
-
Product
Gigabit Ethernet Tester Module for 1G and 10G Packet
GAO-ENET-103
-
GAOTek Gigabit Ethernet Tester Module for 1G and 10G Packet is designed for installation and maintenance of Metro/Carrier Ethernet and IP services. It supplies a compact test solution for 1G and 10G packet Ethernet, including ITU-T Y.1564 standard for SLA and OAM test features.
-
Product
L2-3 Ethernet Tester
Xena Valkyrie
-
The Xena Valkyrie is a feature rich Layer 2-3 stateless Ethernet traffic generator and analysis test platform. It is used to configure and generate Ethernet traffic up at all speeds from 1GE to 800GE. It will analyze network devices and services to see how they perform and respond. An excellent Ethernet test tool for data plane testing in the lab.
-
Product
Ethernet Tester
-
Shanghai Grandway Telecom Tech. Co., Ltd
Datacom tester including 2M Transmission Analyzer, TV Signal Tester, Cable & Antenna Analyzer, 1G(1000M) Ethernet Tester, 10G Ethernet Tester, etc.
-
Product
Field Tester
Ether.Giga
-
ALBEDO Ether.Giga is an Ethernet & IP tester equipped with all the features of legacy testers such as BER and RFC2544, plus the new ones like Y.1564, Y.1731, and FCS error insertion in pass mode therefore it is capable to verify the QoS and SLA of new Multiplay services offering field technicians tools to quickly and easily validate and troubleshoot Ethernet services, including multiplay applications such as VoIP, IPTV, VoD, high-performance Computing, Virtualization Services, Data Centers and Storage that require significant levels of bandwidth.
-
Product
SONET / SDH, OTN, Ethernet and multiservice testers
-
At the core of EXFO’s expertise are next-gen SONET / SDH, OTN, Ethernet and multiservice testers that are designed to take testing to the next level. These instruments address the needs of field technicians seeking ultimate portability and ease-of-use, as well as network managers and systems vendors who require flexible and scalable, future-proof solutions.
-
Product
Ethernet Tester
GAOTek Gigabit
-
GAOTek Gigabit Ethernet Tester is a handheld tester for installation, commissioning and maintenance of 10M/100M/1000M ethernet networks. By combining network performance test & monitoring, data packet sniffing, traffic generation, cable test and BER test in one unit. It is widely used in testing BER of layer 1, layer 2, layer 3, and full-featured RFC-2544 and Y.1564 testing. It can help the front-line field technicians analyze the network quality and locate the fault rapidly.
-
Product
GAOTek Handheld Gigabit Ethernet Test Module
A0070008tek
-
GAOTek Handheld Gigabit Ethernet test module is a highly efficient test instrument which designed for Ethernet layout and integration tests which conforms to Ethernet test standards. This instrument is required for testing from physical layer to service layer of emerging (or next generation) networks. The Ethernet tester is the new Ethernet tester to qualify Ethernet service over LAN and RAN deployment. This is a highly efficient test instrument for service providers to ensure SLA KPIs with the subscribers.
-
Product
Reach Power-over-Ethernet (PoE) Testers
-
After assembly, electronic equipment manufacturers need to test functionally of their products. They want to provide the most test coverage, in the shortest time, for the least cost. When test engineers develop product test plans, they select the most appropriate off-the-shelf general purpose test equipment available. Reach designs and manufactures custom test equipment which is a better fit than general purpose equipment. It not only reduces test time but also reduces costs.
-
Product
Ethernet Tester
ProPlex IQ
-
Ethernet tester for entertainment production applications. Designed with input from production and staging professionals as an all-in-one device, it provides feedback and analysis on any Ethernet protocol, as well as network troubleshooting. It can act as a DMX cable tester, DMX receiver/transmitter, DMX timing analyzer, DMX recorder, RDM controller, or a bidirectional Ethernet-DMX gateway. It is also a PoE tester that can determine the capabilities of any connected PoE source. Finally, it can check SMPTE timecode or act as an LTC receiver/analyzer, and LTC transmitter, and users can use it to update Solaris/ProPlex firmware without a PC.
-
Product
Gigabit Ethernet Tester
GET-100
-
GET-100 is a handheld 10M/100M/1000M gigabit Ethernet tester, used for the Ethernet installation, operation and maintenance services.The GET - 100 design in a small and portable device which provides packet capture, network monitoring, networkperformance testing, data generation, test leads and error test functions in an organic whole unit. It is widely used in network layer 1/2/3 BER test and RFC - 2544 test. GET-100 help maintenance people to quickly locate fault and analysis network
-
Product
Advanced Ethernet Tester
LinkRunner® 10G
-
Quickly test, verify, and troubleshoot 1Gig, Multi-Gig and 10Gig Ethernet (copper, fiber) including line-rate performance testing and packet captureLayer 1-7 AutoTest enables any technician to find network problemsMonitor networks for intermittent issues, every minute for up to 24 hours AllyCare-enables in-depth network discovery features and web remote controlLANBERT™ Media Qualification app tests the capability of premise cabling and media components for carrying Multi-Gig and 10Gig EthernetTwo LinkRunner 10G units can be used for line-rate performance testing to verify network capacity, performance and QoS, as well as service provider SLAs between sites
-
Product
Gearbox Tester
Tester
The gearbox tester was designed to test the Azimuth Drive Unit (ADU) for a missile launcher. The ADU is the horizontal position controller for the launcher. It consists of a main drive shaft, a manual drive shaft and an output drive shaft. This system uses a multi-axis motion controller to operate.
-
Product
Hoist Tester
Tester
The system has the capability of operating hyraulic powered hoists, DC powered hoists and 400Hz AC powered hoists. When a unit is connected to the system it is automatically detected and the system will load the unit's control software, acceptance procedures and operational safety limits. By doing all of this the operator does not need to worry about anything other than installing the unit and clicking Run to execute a full test procedure.
-
Product
Bit Error Rate Tester - PXI
BERT 1001/1005 Series
Tester
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
Product
Automated Coherent Receiver Tester
CoRx Tester.
Receiver Tester
Quantifi Photonics’ CoRx Tester provides automated measurement of key coherent receiver performance parameters. The CoRx Tester is comprised of a pre-configured PXI chassis, a two-channel tunable laser, a polarization controller, and a two-channel Variable Optical Attenuator (VOA) with built-in power meter. Just connect the two optical outputs to your Integrated Coherent Receiver (ICR), connect your ICR to the oscilloscope and let the CoRx Tester software do all the rest.
-
Product
8-Pin M12 Male To 8-Pin RJ50 Male, Shielded, FieldDAQ M12 Ethernet Cable
785944-10
Ethernet Cable
IP67 Gigabit Ethernet, Shielded X-Code M12 Male to RJ45 (Straight), 10M for FieldDAQ
-
Product
Universal A/V Tester
Tester
This tester was built for our client with the specific requirement that specific UUTs can be added to the system by our client. We handled developing test software for the first 2 UUTs utilizing an open programming structure that allowed programming modules to be strung together to create test programs for any additional UUT that our client wants to add in the future.
-
Product
PXIe-8523, 4-Port, 100/1000BASE-T1 PXI Automotive Ethernet Interface Module
787311-01
Ethernet Interface
PXIe, 4-Port, 100/1000BASE-T1 PXI Automotive Ethernet Interface Module - The PXIe-8523 is a 100/1000BASE-T1 unshielded twisted pair (UTP) PXI Automotive Ethernet Interface Module for developing applications with the NI‑XNET driver. With this hardware, you can develop applications … that require Automotive Ethernet to test and validate automotive electronic control units (ECUs). The PXIe-8523 provides up to four independent endpoints or up to two network terminal access points (TAPs). It features onboard hardware timestamping and can act as up to four separate 802.1AS masters or slaves, so it can synchronize with an external network as well as the rest of a PXI system. The PXIe-8523 also provides LEDs on the front panel to help you monitor the network link and activity.
-
Product
Low-Power Ethernet Bridge Converter for MIL-STD-1553 and ARINC
eNetX-MA4
Ethernet Interface
eNetX-MA4™ is an innovative product for “remoting” 1553 & ARINC-429/717 operations on 10/100/1000 Ethernet local area networks (LAN). eNetX-MA4 is a very small, low-power, rugged device that provides real-time UDP connectivity to for 1-2 dual redundant 1553 (A/B) busses and 4 ARINC channels. Tested to MIL-STD-704F/810G/461F and DO160.
-
Product
RJ45 (Ethernet 100 Base T) to 90 Series Interface
J90RJ45I
Ethernet Interface
RJ45 Ethernet connector for VPC Tripaddle ITA moduleUp to 3 connectors per moduleFor Cat 5 Fast Ethernet cable IEEE 802.3 standard100 Base-T
-
Product
1553 EBR to Ethernet Converter
ENET-1553-EBR
Ethernet Interface
ENET-1553-EBR-1D™ is an innovative product that provides “remoting” of 1553 AS5652 EBR operations on 10/100/1000 Ethernet IP/UDP local area networks (LAN). ENET-1553-EBR is a small, low-power, rugged device that provides connectivity for up to eight AS5652 RT devices, single BC or composite monitor.
-
Product
Open/Short Tester for Reverse Engineering Applications
Panther 2K-CT
Tester
Qmax Test Technologies Pvt. Ltd.
Panther 2K-CT is a versatile open\Short tester designed especially for reverse engineering application of tracing circuits of undocumented PCBA’s.Its innovative measurement technology helps tracing PCB tracks between components in a given circuit board. It can accommodate various types of clips\grabbers and connectors to access the device pins to trace the connectivity. Its user friendly software guides the user to place and move cluster of IC clips and probes to learn the connectivity and to generate netlist.
-
Product
8-Pin M12 Male To 8-Pin M12 Male, Shielded, FieldDAQ M12 Ethernet Cable
785946-01
Ethernet Cable
IP67 Gigabit Ethernet, Shielded X-Code M12 Male to Shielded M12 Male (Straight), 1M for FieldDAQ
-
Product
ITxPT M12 8GE Unmanaged Switch
EKI-9508G-ST
Ethernet Switch Module
M12 connector with IP67 rugged housing, Complies with ITxPT, E-Mark, Complies with UN ECE R118 & UN ECE R10. Supports PoE IEEE802.3af/at (PoE model) Wide nominal power input range: 12/24VDC; Operating power input range: 9-36VDC. Compact size to fit in different narrow spaces, Operating temperature: -40 ~ 70°C, Support power ignition, Support power delay-off.
-
Product
8FE + 2GE Combo Port Unmanaged Switch
EKI-2710E-2CI
Ethernet Switch Module
Provides 8FE+2GE combo port with Auto MDI/MDI-X, Supports 8 x 10/100 Mbps Auto-Negotiation + 2 x Combo 10/100/1000M Auto-Negotiation. Supports redundant 12 ~ 48 VDC power input, Supports DIP Switch Configuration: QoS/BSP/port-based VLAN, Supports EMC Level 4 protection for extreme outdoor environments.
-
Product
E-Mark M12 8FE PoE Unmanaged Switch
EKI-9508E-PS
Ethernet Switch Module
M12 connector with IP67 rugged housing, Complies with E-Mark, Complies with UN ECE R118 & UN ECE R10. Supports PoE IEEE802.3af/at (PoE model) Wide nominal power input range: 12/24VDC; Operating power input range: 9-36VDC. Compact size to fit in different narrow spaces, Operating temperature:-40 ~ 70°C.
-
Product
24GE+4G Combo Unmanaged Ethernet Switch
EKI-2428G-4CI
Ethernet Switch Module
19" Rackmount, -40~75℃, 24 x Gigabit ports + 4 x Gigabit copper/SFP combo ports, SFP socket for Easy and Flexible Fiber Expansion. Provides 8K MAC address, Supports 12-48V DC power input, -40 ~ 70°C wide-range operating temperature.
