Filter Results By:
Products
Applications
Manufacturers
FMC
-
product
Flexible Magnetic Coupler
FMC
The FMC (Flexible Magnetic Coupler) is a partial discharge sensor whose working principle is based on a direct magnetic coupling with the cable conductor and shield.It picks up a magnetic signal given by PD activity. His compact and robust design makes the FMC the optimal sensor for direct installation on cables and accessories such as joints and termination.This sensor has a sensitive side which has to face to the object under test, while the other side (shielded) reject the noise from the environment.
-
product
FMC for Data Communication Dual 1 Gigabit Ethernet FMC
FMC431
Sundance Multiprocessor Technology Ltd.
The FMC431 is a dual 1 Gigabit Ethernet FPGA Mezzanine Card with two RJ45 connectors available on the front panel. Compliant with the VITA 57.1 standard the FMC431 offers a High Pin Count connector but is compatible with FPGA carrier cards with Low Pin Count connectors. The Ethernet interface (1000BASE-T) is either implemented using RGMII (Low Pin Count compatible) or SGMII (High Pin Count compatible). The FMC431 also offers the option to stack an additional FMC over it. Any of the 4DSP FMC that use LVDS and single ended signaling only can be mounted over the FMC431, thus offering users with the ability to build a complete data acquisition, waveform generation and communication solution while using a single FMC site on an FPGA carrier card. The FMC431 is an ideal solution to bring Ethernet connectivity to an FPGA based system and ensure reliable external communication.
-
product
4-Channel ADC Module
FMC125
Sundance Multiprocessor Technology Ltd.
The FMC125 is a Quad-Channel Multi-Mode A/D FMC, fully compliant with VITA 57.1 Standards. The card provides four 8-bit ADC channels that enable simultaneous sampling of 4, 2, or 1 channel with a maximum sample rate of 1.25 GSPS (4-channel mode), 2.5 GSPS (2-channel mode), or 5.0 GSPS (1-channel mode).
-
product
FPGA Mezzanine Card
FMC134
The FMC134 provides customers with a high bandwidth and high channel count I/O solution that is ideal for multi-channel receivers in a wide range of applications.With four 12-bit analog-to-digital channels up to 3.2GSPS or two analog channels up to 6.4GSPS, the FMC134’s design is based on the Texas Instruments™ ADC12DJ3200 and is mechanically and electrically compliant with the FMC+ standard (VITA 57.4), the next generation of small form factor expansion I/O for high performance FPGA-based systems.
-
product
PCIe FPGA Carrier For FMC+, Kintex UltraScale™
PCI592
The PCI592 is based on the Xilinx XCKU115 Kintex UltraScale FPGA, which provides 5,520 DSP slices, 75.9 Mb RAM and 1,451,000 logic cells. The FPGA interfaces directly to the FMC+ DP-23 and all FMC+ LA/HA/HB pairs, making it compatible with a wide range of industry standard VITA 57 modules. It also has interface to three DDR4 memory channels (2x 64-bit wide and 1x 32-bit wide). This allows for large buffer sizes to be stored during processing as well as for queuing the data to the host. The unit has x8 PCIe edge connector routed to the FPGA PCIe Gen3 hard IP block. In addition, 16 uncommitted connection pairs are routed to a dual x8 expansion connector, providing direct connectivity to a neighbouring FPGA (e.g. via Aurora, 10G/40G, SRIO, PCIe) without the need to go through the host.
-
product
PXIe Module
PXIe700
Sundance Multiprocessor Technology Ltd.
PXIe700 is a powerful, flexible and expandable PXIe module fully compatible with PXI™-5 and ANSI-Vita-57.1 FMC carrier standards. PXIe is the platform of choice for the test, measurement and instrumentation market. The presence of an FMC site gives the ability to add different functionalities through the many available FMCs from various vendors.
-
product
2-channel RF Transceiver Module
FMC30RF
Sundance Multiprocessor Technology Ltd.
The FMC30RF is an FMC Daughter Card which is fully compliant with the VITA 57.1-2010 standard. The FMC30RF offers in a small footprint a low power and fully featured Rx / Tx signal path for the development and deployment of advanced RF solutions. With a frequency range coverage from 400MHz to 3.0GHz* and up to 60MHz* bandwidth the FMC30RF provides flexibility and reconfigurability to a host of applications.
-
product
Quad 6 Gsps 12-bit ADC
ADF-Q6012
The DEG ADF-Q6012 FMC includes four 12-bit, 6 Gsps RF analog-to-digital converters (ADC). The ADF-Q6012 features a 16-lane, 24.75 Gbps JESD204C interface, flexible clocking and triggering options. This ADF-Q6012 leverages two Analog Devices AD9207 MxFE (Mixed Signal Front End) ICs, elevating the technology to a new level of integration.
-
product
4-channel ADC Module
FMC140
Sundance Multiprocessor Technology Ltd.
The FMC140 is an analog-to-digital (A/D) FMC daughter card that provides four 16-bit A/D channels at 370MSPS which can be clocked by an internal clock source (optionally locked to an external reference) or by an externally-supplied sample clock. A trigger input is also available for customized sampling control. The FMC140 is mechanically and electrically compliant to the FMC standard (ANSI/VITA 57.1-2010). It offers front panel analog I/O access and can be used in a conduction-cooled environment.
-
product
10 Channel ADC FMC Module
ADCFN10-AC – HPC
Sundance Multiprocessor Technology Ltd.
The RFM-ADCFN10 is a ten channel Analog to Digital converter FMC which complies with VITA 57.1-2010. Each channel provides single-ended analog input and 16-bit single-ended output with 20-105MHz sampling speed based on ADI AD9650. Both AC and DC coupled input are supported. Single-ended external clock, differential external clock or an internal clock from the FMC carrier board can be selected at the FMC for the AD converter through fine clock generator ADI AD9518-3.
-
product
Carrier - Virtex 7 W/FMC Site
VPF: 3U VPX
The VPF is a VPX form factor (VITA 46), FPGA processor board designed to meet the needs of challenging, embedded high‐performance digital signal processing applications at a competitive price point. AMD Virtex 7: VX330 and VX690 population options are available. The Virtex 7 FPGA provides impressive processing capabilities and supports operations such as: FFTs, FIR filters, fixed‐point and repetitive processing tasks. The VPF FPGA node processes input from the FMC HPC (Vita 57.1) site, allowing for maximum application configurability and performance when coupled with DEG’s market leading ADC and DAC FMC modules (250MSPS to 4.0GSPS). The VPF is fully compliant with the OpenVPX standard and accommodates the PCIExpress Gen 3.0 communication protocol. Delphi also offers a VPF FPGA Design kit which allows customers to leverage and modify DEG source code, develop within an open architecture, and rapidly integrate FPGA HDL. The DEG FPGA Design kit includes: Source code, simulation test bench and utilities to support custom algorithm development. Embedded Linux, VX Works and Windows software drivers are available. HPC FMC Site, Fully Compatible with all Delphi ADC and DAC FMC Modules.
-
product
JadeFX Kintex UltraScale Processor and FMC Carrier - 3U VPX
Model 5983
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family BrochureVITA-57.4 HSFC FMC+ site offers access to a wide range of possible I/O- Supports Xilinx Kintex UltraScale FPGAs- 9 GB of DDR4 SDRAM- On-board GPS receiver- PCI Express (Gen. 1, 2 and 3) interface up to x8- User-configurable gigabit serial interface- LVDS connections to the Kintex UltraScale FPGA for custom I/O- Optional optical interface for backplane gigabit serial interboard communication- Compatible with several VITA standards including: VITA-46, VITA-48 AND VITA-66.4 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available
-
product
GMSL II Output FMC Module with MAX96705
TEF0010-01
Sundance Multiprocessor Technology Ltd.
FMC module with Xilinx Artix-7 FPGA and 4 x 16-Bit GMSL serializers.
-
product
4-Channel DAC FMC Module
SMT-FMC211 – LPC
Sundance Multiprocessor Technology Ltd.
The main component of the SMT-FMC211 is the Texas Instruments 4 channel DAC – TI’s Quad 1.25GHz DAC3484. This device offers excellent SFDR performance better than 70dBc, with an output sample rate of over 312MSPS. It interfaces to an Artix-7 XC7A15T-2C FPGA using a 16 bit differential DDR bus.
-
product
Octal 1.4 Gsps, 14-bit ADC FMC+
ADF-O1414
The ADF-O1414 ADC FMC+ module from DEG delivers eight channels, each with 14 bits of resolution at a sample rate of 1.4 Gsps. Utilizing the Analog Devices AD9695 ADC, the ADF-O1414 enables defense applications requiring higher dynamic range, greater ENOB and wideband sampling performance.
-
product
FPGA/FMC Carriers
Our AMC FPGA modules feature Altera Stratix IV, Altera Stratix V, Xilinx Virtex-5, Xilinx Virtex-6, Xilinx Zynq, Xilinx Artix, Xilinx Virtex-7 and Xilinx Kintex-7 FPGAs. We also offer a range of carriers that can accommodate standard FMCs featuring FPGAs from Altera and Xilinx, including the new Xilinx UltraScale family.
-
product
DAQ FMC Modules
Sundance Multiprocessor Technology Ltd.
FMC Modules with both Analog to Digital and Digital to Analog sections.
-
product
PCIExpress Kintex UltraScale FPGA Carrier Board
PCU: 085/115
The PCU continues DEG’s commitment to delivering high performance processing solutions for mission critical applications requiring the latest in AMD Kintex UltraScale FPGA computing power. The PCU is a PCIExpress, standard form factor , FPGA processor board designed to meet the needs of challenging, embedded high-performance digital signal processing applications at a competitive price point. AMD Kintex UltraScale XCKU085/115 delivers impressive processing capabilities and supports operations such as: FFTs, FIR filters, fixed-point and repetitive processing tasks. The PCU FPGA node processes input from the FMC HPC +(Vita 57.4) site, allowing for maximum application configurability and performance when coupled with DEG’s market leading ADC and DAC FMC modules (250MSPS to 12.0GSPS).
-
product
PCIe/104 OneBank SBC w. Dual 1GHz ARM9
EMC²-Z7030
Sundance Multiprocessor Technology Ltd.
The PCIe/104 OneBank™ design enables the EMC²-Z7030 to be added to robust and rugged installations for various commercial, medial, industrial and military uses and to enable more versatility the EMC²-Z7030 also incorporates a VITA57.1 FMC™ LPC connector opening up an range of extra possibilities and expansion options.
-
product
PCIe/104 OneBank I/O Board
EMC²-7K70
Sundance Multiprocessor Technology Ltd.
The PCIe/104 OneBank™ design enables the EMC²-7K70T to be added to robust and rugged installations for various commercial, medial, industrial and military uses and to enable more versatility the EMC²-7K70 also incorporates a VITA57.1 FMC™ LPC connector opening up an range of extra possibilities and expansion options.
-
product
FMC, XMC & PMC
The FPGA Mezzanine Card is used by Data Patterns to implement signal interface with external world compatible FPGAs mounted on the FMC carrier there are primarily used for high speed analog interface for digitization (ADCs) and waveform generation (DACs). This form factor is also utilized for special I/O Interfaces such as various avionic protocols and buses. FMC I/O signals may be routed via front panel connectors or through Mezzanine connectors that route the signal back to the carrier board for routing through rear I/O of the Chassis. The system interface is designed for routing to FPGAs using a VITA 57 0.05 Pitch Terminal Array Assembly.
-
product
2ch ADC, 2ch DAC
RFM-ADAFF22
Sundance Multiprocessor Technology Ltd.
The RFM-ADAFF22 is a two channel Analog to Digital and two channel Digital to Analog mixed converter FMC which complies with VITA 57.1-2010. Each AD channel provides AC coupled single-end analog input and 16-bit single-ended output with 20-105MHz sampling speed based on ADI AD9650. Each DA channel provides 16-bit single-ended input and one DC coupled differential analog output with 1 – 500MHz sampling speed based on Maxim MAX5888A.
-
product
OnyxFX FlexorSet 4-Ch. 250 MHz A/D, 2-Ch. 800 MHz D/A - PCIe
Model 7070-312
Model 7070-312 is a member of the Flexor® family of high-performance PCIe boards based on the Xilinx Virtex-7 FPGA. As a FlexorSetTM integrated solution, the Model 3312 FMC is factory-installed on the 5973 FMC carrier. The required FPGA IP is installed and the board set is delivered ready for immediate use.
-
product
FMC Dual ADC 12-bit 2.6 GSPS, Single DAC 16-bit 12 GSPS
FMC250
The FMC250 is an FPGA Mezzanine Card (FMC+) per VITA 57.4 specification. The board has dual ADC and single DAC. The FMC250 utilizes dual AD9625 ADCs providing 12-bit conversion rates of up to 2.6 GSPS and a single DAC (AD9162 or AD9164) providing 16-bit conversion rates of up to 12 GSPS. The analog input, digital output, clock and trigger interfaces of the FMC250 are routed via SSMC connectors. The internal clock frequency is programmable and the clock is capable of locking to an external reference.
-
product
2-Channel DAQ Module
FMC150
Sundance Multiprocessor Technology Ltd.
The FMC150 is a dual channel ADC and dual channel DAC FMC daughter card. The card provides two 14-bit A/D channels and two 16-bit D/A channels which can be clocked by an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. In addition there is one trigger input for customized sampling control. The FMC150 daughter card is mechanically and electrically compliant to the FMC standard (ANSI/VITA 57.1).
-
product
Gen 4 X16 PCIExpress UltraScale+ FPGA Carrier Board
PG4
The PG4 continues DEG’s commitment to delivering high performance processing solutions for mission critical applications requiring the latest in AMD UltraScale+ FPGA computing power. The PG4 is a PCIExpress, Gen 4 x16, FPGA processor board designed to meet the needs of challenging, embedded high-performance digital signal processing applications. The AMD UltraScale+ VU33P delivers impressive processing capabilities and supports operations such as: FFTs, FIR filters, fixed-point and repetitive processing tasks. The PG4 FPGA processes input from the FMC+ HPC (Vita 57.4) site, allowing for maximum application configurability and performance when coupled with DEG’s market leading ADC and DAC FMC modules (250MSPS to 12.0GSPS).
-
product
Dual Channel Mini-SAS I/O FMC
FM550
Sundance Multiprocessor Technology Ltd.
The FM550 is an I/O module equipped with two external mini-SAS x4 connectors. I/O FMCs of this sort are typically used to provide inter-module connectivity via the front-panels of carrier cards fitted with similar interfaces, or fan-out to multiple external devices such as mini-SAS drives.
-
product
FMC Module
SMT-FMC510L
Sundance Multiprocessor Technology Ltd.
The SMT-FMC510L is an FMC module with a low pin count connector (LPC). It is primarily designed to attach to the EMC2-DP FMC PCIe104 carrier board and provide analogue video and serial interfaces. Connectivity is via BNC connectors on the main FMC PCB, BNC connectors on an adaptor PCB, and two 20-way latching DIL pin headers. The adapter PCB is optional and only required if interfaces other than analog video are needed.
-
product
Development System
PCIe490
The PCIe490 Expansion Chassis enables users to scale application workstations with up to eight additional PCIe boards per chassis and up to 63 total slots with chassis daisy chaining. It was designed to accommodate the Abaco Systems PC820 and PC821 with Xilinx Ultrascale technology and multiple FMC+ interfaces.
-
product
PC/104 OneBank Board
EMC2-SoM3-300
Sundance Multiprocessor Technology Ltd.
The PCIe/104 OneBank™ design enables the EMC²-SoM3-300 to be added to robust and rugged installations for various commercial, medical, industrial and military uses and to enable more versatility the EMC²-SoM3-300 also incorporates a VITA57.1 FMC™ LPC connector opening up an range of extra possibilities and expansion options.
