FMC
-
Product
Multi I/O FMC Module
FMC155
-
The FMC155 is an FPGA Mezzanine Card (FMC) per VITA 57.1 standard, offering a small footprint and allowing for general-purpose I/O expansion. The FMC155 provides sixteen LVDS input/outputs, eight RS-485/422 RX plus eight RS-485/422 TX, and sixteen single-ended +3.3 V input/outputs.
-
Product
Floating-Point C6678 DSP Module
FMC667
-
Sundance Multiprocessor Technology Ltd.
The FMC667 is a Digital Signal Processor FMC daughter card based on the Texas Instruments TMS320C6678 device. The FMC667 daughter card is mechanically and electrically compliant with the FMC standard (ANSI/VITA 57.1), and can be used in a conduction cooled environment. This FMC is equipped with power supply and temperature monitoring and offers several power-down modes to switch off unused functions and peripheral interfaces. Several Gigabit differential pairs from the FMC connector are used to implement a PCIe and Serial Rapid IO interface between the FMC and the carrier.
-
Product
PCIe Gen3 x8 FMC Module
PXI Express Module
VITA 57.1 FMC HPC ConnectorPCIe Gen3/Gen2/Gen1 x8 Slot (upto 64Gbps)Single module supports both PCIe Root Port & EndpointM.2 Key-M NVMe slot with PCIe Gen3 x2 interface & SATA3.0 interfaceMIPI DSI & CSI Connector through LVDS IOs32Kb-EEPROM
-
Product
4-Channel ADC FMC Module
FMC103 – LPC
-
Sundance Multiprocessor Technology Ltd.
The FMC103 is a four-channel ADC FMC (FPGA Mezzanine Card) which is fully compliant with the VITA 57.1-2010 standard. The FMC103 card provides four 12-bit 210 MSPS A/D channels which can be sampled by an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. A trigger input for customized sampling control is also available. The FMC103 has the LPC (Low-Pin Count) 160-Pin connector, front panel I/O, and is conduction cooled compliant. The board is also available with Mil-I-46058c compliant Conformal Coating.
-
Product
FMC SpaceWire/SpaceFibre Board
316
-
The FMC-SpaceWire/SpaceFibre board is an FPGA Mezzanine Card which is designed to extend the capabilities of an FPGA development board by adding support for SpaceWire and SpaceFibre interfaces. The board has four SpaceWire ports with accompanying status LEDs, and two SpaceFibre ports.
-
Product
6U OpenVPX PMC/XMC rear transition module.
EnsembleSeries™ RTM60P
-
*High-density connector and breakout cable to access to RS-232/RS-422 serial and 10/100/1000BASE-T Ethernet interfaces*Four 9-pin serial interfaces and four RJ45 Ethernet interfaces via the breakout cable*Standard VITA 57 FMC connectors that map to the PMC and XMC user I/O connections from the HCD6220 or HCD6410
-
Product
FPGA Card
PC820
-
The PC820 is a high-performance, PCI Express card with advanced DSP capabilities and multiple I/O options. It supports one FMC+ VITA 57.4-compliant HPC FPGA Mezzanine Card (FMC) that is closely coupled to the Virtex or Kintex UltraScale FPGA and a DDR4-2133 SDRAM SO-DIMM. The PC820s PCIe Gen3 interface can support up to eight lanes.
-
Product
PCIe FPGA Carrier For FMC, Virtex UltraScale™
PCI595
-
The PCI595 is based on the Xilinx XCVU440 Virtex UltraScale FPGA, which provides 2,880 DSP slices, 88.6 Mb RAM and 5,541,000 logic cells. The FPGA interfaces directly to the FMC DP 0-9 and all FMC LA/HA/HB pairs, making it compatible with a wide range of industry standard VITA 57 modules. It also has interface to one DDR4, 64-bit wide, with 8 GB total memory. This allows for large buffer sizes to be stored during processing as well as for queuing the data to the host.
-
Product
PC/104 OneBank Board
EMC2-ZU3EG
-
Sundance Multiprocessor Technology Ltd.
The EMC²-ZU3EG is a PCIe/104 OneBank™ SBC with a Xilinx Zynq SoC and a VITA57.1 FMC™ LPC I/O board. The main processing power of the EMC²-ZU3EG is a Dual Core ARM9 and combined with traditional FPGA fabrics/gates + High-Speed I/O interfaces, like USB2.0, HDMI, 1Gb Ethernet and SATA and provide an total solution for any Embedded Application.
-
Product
4-Channel DAQ Module
FMC144
-
Sundance Multiprocessor Technology Ltd.
The FMC144 is an analog-to-digital (A/D) and digital-to-analog (D/A) FMC daughter card that provides four 16-bit A/D channels at 370MSPS and four 16-bit D/A channels at 2.5GSPS which can be clocked by an internal clock source (optionally locked to an external reference) or by an externally-supplied sample clock.
-
Product
FMC-HPC ADC Board
FMC121
-
Sundance Multiprocessor Technology Ltd.
The FMC121 provides two 16-bit A/D channels up to 1Gsps and two 16-bit D/A channels up to 1.4 Gsps data rate with a 2.8 GSPS update rate. The design is based on Texas Instruments’ ADS54J60 Analog-to-Digital converter and Texas Instruments DAC39J84 Digital-to-Analog converter. The sample clock can be supplied externally through a coaxial connection or supplied by an internal clock source (optionally locked to an external reference) for multi-channel synchronization. An external trigger input is available for timing synchronization. The FMC121 is mechanically and electrically compliant to the FMC standard (ANSI/VITA 57.1).
-
Product
4-Channel ADC Module
FMC104
-
Sundance Multiprocessor Technology Ltd.
The FMC104 is a four-channel ADC FMC (FPGA Mezzanine Card) which is fully compliant with the VITA 57.1-2010 standard. The FMC104 card provides four 14-bit 250 MSPS A/D channels which can be sampled by an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. A trigger input for customized sampling control is also available.
-
Product
FMC for High Speed Optical Communication Dual QSFP+ FMC
FMC424
-
Sundance Multiprocessor Technology Ltd.
The FMC424 is a dual QSFP+ FPGA Mezzanine Card. Electrically compliant with the VITA 57.1 standard the FMC424 is compatible with 4DSP FPGA carrier cards offering High Pin Count connectors. It also allows for the option to stack an additional FMC over it. Any of the 4DSP FMC that use LVDS and single ended signaling only can be mounted over the FMC424, thus offering users with the ability to build a complete high speed data acquisition, waveform generation and optical communication solution while using a single FMC site on an FPGA carrier card.
-
Product
8-Channel ADC Module
FMC108
-
Sundance Multiprocessor Technology Ltd.
The FMC108 is an eight-channel ADC FMC (FPGA Mezzanine Card) which is fully compliant with the VITA 57.1-2010 standard. The FMC108 card provides eight A/D 14-bit 250MSPS channels which can be sampled by an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. A trigger input for customized sampling control is also available. The FMC108 has the HPC (high-pin count) connector, front panel I/O, and is conduction cooled compliant. The board is also available with Mil-I-46058c compliant Conformal Coating.
-
Product
FMC-HPC ADC Board
FMC123
-
Sundance Multiprocessor Technology Ltd.
The FMC123 provides four 16-bit A/D channels up to 1Gsps. The design is based on Texas Instruments’ ADS54J60 Analog-to-Digital converter. The sample clock can be supplied externally through a coaxial connection or supplied by an internal clock source (optionally locked to an external reference) for multi-channel synchronization. An external trigger input is available for timing synchronization. The FMC123 is mechanically and electrically compliant to the FMC standard (ANSI/VITA 57.1).
-
Product
PC/104 OneBank Board
EMC2-ZU4EV
-
Sundance Multiprocessor Technology Ltd.
The EMC²-ZU4EV is a PCIe/104 OneBank™ SBC with a Xilinx Zynq SoC and a VITA57.1 FMC™ LPC I/O board. The main processing power of the EMC²-ZU4EV is a Dual Core ARM9 and combined with traditional FPGA fabrics/gates + High-Speed I/O interfaces, like USB2.0, HDMI, 1Gb Ethernet and SATA and provide an total solution for any Embedded Application.
-
Product
Quad 12.0 Gsps 16-bit DAC FMC+ Module
DAC-Q30
-
The DAC-Q30 FMC+ module from DEG is a high sample rate, 16 bit quad channel DAC module. The Analog Devices AD9174 DAC device operates at 3.0 Gsps natively and up to 12.0 Gsps in interpolation mode. A VITA 57.4-compliant FPGA Mezzanine Card (FMC+) interface, the DAC-Q30 offers industry wide platform compatibility with the PCIe/VME/VXS/VPX carrier board of your choice. The DAC-Q30 and associated HDL firmware are compatible with AMD FPGAs.
-
Product
12-Channel ADC Module
FMC112
-
Sundance Multiprocessor Technology Ltd.
The FMC112 is a twelve-channel ADC FMC Daughter Card which is fully compliant with the VITA 57.1-2008 standard. The FMC112 provides twelve A/D 14-bit 125Msps channels which can be sampled by an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. A trigger input for customized sampling control is also available. The FMC112 has the LPC (Low-Pin Count) connector, front panel I/O, and is conduction cooled capable.
-
Product
PCB Connectors
-
Rosenberger Hochfrequenztechnik GmbH & Co. KG
Rosenberger offers a wide range of PCB connectors, which are tailored to the high demands of industrial test applications. The product range includes many common standard RF series, e.g. SMP, WSMP, Mini-SMP, SMA, QMA, SMB, MCX or Mini-Coax, but also innovative coaxial series such as P-SMP, Longwipe-SMP, FMC or Micro-RF.For specific test & measurement applications, Rosenberger develops and produces modular connector systems for DC frequencies up to 50 GHz, solderless PCB mount connectors for ultra-high frequency applications up to 110 GHz or spring-loaded coax systems ( > 2,500 matings, pairwise phase matching 10 ps standard, different cable lengths).
-
Product
DSP FMC Modules
-
Sundance Multiprocessor Technology Ltd.
FMC Modules with Digital Signal Processors
-
Product
FPGA Mezzanine Card (FMC)
FMC DEL
-
Sundance Multiprocessor Technology Ltd.
An FPGA Mezzanine Card (FMC) created to produce pulses delayed by a user-programmed value with respect to the input trigger pulse. It has 4 output channels and one input trigger. The delay from the trigger input to each of the outputs can be set independently in a range from 600 ns to 120 seconds. It is implemented using a dedicated time-to-digital converter IC from the European company Acam.
-
Product
Quad 3.1 Gsps, 14-bit ADC FMC+
ADF-Q3114
-
The ADF-Q3114 is a VITA 57.4 compliant FPGA Mezzanine Card (FMC+) that converts four channels of up to 3.1 GHz analog input bandwidth. This digitizer provides unparalleled analog-to-digital conversion capability with the PCIe/VME/ VXS/VPX carrier board of your choice. The ADF-Q3114 is designed to be compatible with AMD FPGA platforms.
-
Product
FPGA Mezzanine Card
FMC150
-
The FMC150 is a dual channel ADC and dual channel DAC FMC daughter card. The card provides two 14-bit A/D channels and two 16-bit D/A channels which can be clocked by an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. In addition there is one trigger input for customized sampling control.
-
Product
Quad 12 Gsps 16-bit DAC& Quad 4 Gsps 12-bit ADC
ADF-QMx44
-
The DEG ADF-QMx44 FMC leverages the Analog Devices AD9081 MxFE (Mixed Signal Front End) transceiver technology. This highly integrated device includes a quad 16-bit, 12 Gsps sample rate radio frequency (RF) digital-to-analog converter (DAC) and a quad 12-bit, 4 Gsps rate RF analog-to-digital converter (ADC). The ADF-QMx44 features an 8-lane, 24.75 Gbps JESD204C transceiver port, an on-chip clock multiplier, digital signal processing capability and supports four transmitter channels and four receiver channels.
-
Product
Quad QSFP28/QSFP+ FMC+ Module
FPGA Board
iWave’s QSFP28/QSFP+ 2×1 Stacked FMC+ HSPC Module is designed to meet VITA 57.4 FMC+ Standard. This FMC+ Module is supported by two stacked QSFP28/QSFP+ ports(Upto400G) with 4-Bit Silicon Labs programmable clock synthesizer (default = 156.25Mhz). A flexible reference clock for on the QSFP28/QSFP+ 2×1 Stacked FMC+ Module is fully programmable over the 0.16 to 710 MHz range through I2C. Each QSFP28/QSFP+ ports are directly connected to four multi-gigabit serial transceivers banks of Vita 57.4 compliant carrier Board.
-
Product
FMC Module
SMT-FMC510L
-
Sundance Multiprocessor Technology Ltd.
The SMT-FMC510L is an FMC module with a low pin count connector (LPC). It is primarily designed to attach to the EMC2-DP FMC PCIe104 carrier board and provide analogue video and serial interfaces. Connectivity is via BNC connectors on the main FMC PCB, BNC connectors on an adaptor PCB, and two 20-way latching DIL pin headers. The adapter PCB is optional and only required if interfaces other than analog video are needed.
-
Product
FPGA Mezzanine Card
FMC134
-
The FMC134 provides customers with a high bandwidth and high channel count I/O solution that is ideal for multi-channel receivers in a wide range of applications.With four 12-bit analog-to-digital channels up to 3.2GSPS or two analog channels up to 6.4GSPS, the FMC134’s design is based on the Texas Instruments™ ADC12DJ3200 and is mechanically and electrically compliant with the FMC+ standard (VITA 57.4), the next generation of small form factor expansion I/O for high performance FPGA-based systems.
-
Product
PC/104 OneBank I/O Board
EMC²-KU35
-
Sundance Multiprocessor Technology Ltd.
The PCIe/104 OneBank™ design enables the EMC²-KU35 to be added to robust and rugged installations for various commercial, medial, industrial and military uses and to enable more versatility the EMC²-KU35 also incorporates a VITA57.1 FMC™ LPC connector opening up an range of extra possibilities and expansion options.
-
Product
FMC, XMC & PMC
-
The FPGA Mezzanine Card is used by Data Patterns to implement signal interface with external world compatible FPGAs mounted on the FMC carrier there are primarily used for high speed analog interface for digitization (ADCs) and waveform generation (DACs). This form factor is also utilized for special I/O Interfaces such as various avionic protocols and buses. FMC I/O signals may be routed via front panel connectors or through Mezzanine connectors that route the signal back to the carrier board for routing through rear I/O of the Chassis. The system interface is designed for routing to FPGAs using a VITA 57 0.05 Pitch Terminal Array Assembly.
-
Product
Dual 2.0 Gsps. 12 Bit ADC FMC
ADF-D2000
-
This FPGA Mezzanine Card (FMC) converts two channels of up to 2.8GHz analog input bandwidth at 1.0, 1.6, 1.8, or 2.0 Gsps and 12-bit resolution. Additionally, this FMC can be used in an interleaved mode to convert a single channel at 2.0, 3.2, 3.6, or 4.0 Gsps and 12-bit resolution. Based on the VITA 57 specification, the ADF-D1600 enables direct coupling of unparalleled analog-digital conversion capability with the VME/VXS/AMC/VPX/PCI-E carrier board of your choice. DEG engineers have designed this product and associated HDL firmware to work with both Altera and AMD FPGAs.
