Optical Attenuators
Reduce optical power by inducing loss.
-
Product
Digital Attenuator
-
Chengdu KeyLink Microwave Technology Co., Ltd.
The products can be used in microwave electronic components. Its attenuation values are determined by the input TTL/LVTTL control signal. So that the link can be achieved the desired gain or loss value.KeyLink's digital attenuators can be categorized as follows.
-
Product
Manual Step Attenuator, DC to 4 GHz, 0 to 110 dB, 10 dB steps
8496A
Attenuator
The Keysight 8496A dc to 4 GHz manual step attenuator offers exceptional repeatability and reliability. Attenuation is provided in 10 dB steps from 0 to 110 dB. Precision gold-plated leaf springs ensure long life (over 5 million cycles) and very high attenuator repeatability (typically 0.01 dB). To improve measurement accuracy, NIST traceable data (SWR and attenuation) is available as Option UK6. Custom step attenuator/switch combinations are possible. The Keysight 11716A/B/C interconnect kits provide quick connection of Keysight 8494/5/6/7 1 dB and 10 dB step attenuators in series for greater dynamic range with 1 dB steps.
-
Product
Programmable Attenuators
-
a programmable attenuator from Pasternack. Our SMA attenuator is a programmable step attenuator design. This 50 Ohm adjustable attenuator is precision manufactured to RF and microwave industry specifications.
-
Product
Variable attenuator
-
Optimum for simulation of wireless communication equipments, such as handover test, dynamic motion test and receiving sensitivity test. Moreover, optimum for the simulation of the receiving trouble by the rainfall attenuation in BS/CS digital broadcasting.
-
Product
RF Attenuators
-
Bird manufactures a broad spectrum of devices from 2 W to 4000W. Our resistive product portfolio includes air-cooled, water-cooled, oil-dielectric, convection cooled, and conduction cooled RF attenuators with a wide range of connectors and attenuation values.
-
Product
PXI Attenuator Modules
-
Programmable RF Attenuators – accurate DC to 3GHz programmable attenuator has a 1dB step resolution, allowing it to adjust signal amplitudes for optimum measurement by other devices.Solid State Programmable RF Attenuators – available in triple or hex formats with bandwidths between 10MHz and 6GHz.High Voltage Attenuators – provide a convenient way of attenuating high voltage low frequency signals to levels that can be captured by other PXI devices without risk of damaging them.
-
Product
Variable Attenuators
-
Wuhan Sunma Technology Co., Ltd.
SunmaFiber offer optical variable attenuator is used for continuously variable optical signal attenuation. As the attenuator is used in the laser system for the on-line testing, there can be used in the digital system of communication devices (such as:PHD, SDH) and also in the system of adopting analog modulation (CATV).
-
Product
Fixed Attenuator (Waveguide)
-
RF Lambda’s fixed waveguide attenuators are used to attenuate RF signals with a waveguide interface. They come in a variety of different frequencies and power levels depending on the application.
-
Product
PXI Single 4 Channel Mux Fibre Optic LC
40-850-414
Fiber Optic Switch
The 40-850-414 4-channel multiplexer is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
Voltage Variable Attenuators
-
Analog Devices voltage variable attenuators (VVAs) ensure accurate control for a wide range of applications. Our absorptive VVAs are ideal for designs where an analog dc control signal controls RF signals levels over a 30 dB amplitude range, while our monolithic VVAs feature low insertion loss, high IP3, and wide dynamic range, as well as a balanced topology that delivers excellent return loss.
-
Product
Step Attenuators
-
A stepped attenuator from Pasternack. Our BNC attenuator is a RF step attenuator design. This 50 Ohm manual step attenuator is precision manufactured to RF and microwave industry specifications.
-
Product
Attenuators
-
A device consisting of an arrangement of resistors which reduces the strength of a radio or audio signal.
-
Product
RF Attenuators
-
Over 400 coaxial, surface mount, and MMIC attenuator models for 50-Ohm & 75- Ohm syetem including fixed attenuators, high-power attenuators, digital step / programmable attenuators, voltage variable attenuators and more. DC passing and DC blocking models. Power handling up to 100W. Bandwidths spanning DC to 50 GHz.
-
Product
Broadband Optical Source - PXI
SLED 1000 Series
Optical Source
The SLED 1000 Series is a super-luminescent LED light source with high output power, large bandwidth and low spectral ripple. It comes in various wavelength models to address applications in the telecom and datacom markets.The SLED is a single-slot PXIe module and is ideal for building a customized optical testing platform that delivers reliable and repeatable results in manufacturing or R&D environments.
-
Product
Voltage Variable Attenuators
-
Voltage variable attenuators (VVAs) that offer up to 60 dB of attenuation across a broad range of frequencies from 400 MHz to 18 GHz. These voltage variable attenuators are frequently used in applications such as electronic warfare, instrumentation, point-to-point and point-to-multipoint radios, fiber optic and broadband telecom, microwave radio and VSAT, military radios, radar, ECM, SATCOM and sensors, and R&D.
-
Product
POWER ATTENUATORS
TYPE ATF
-
National RF’s Type ATF Power Attenuators were designed to allow interfacing of linear power amplifiers to RF exciters, where a specific amount of drive to the amplifier is prescribed. Often, however, drive from the RF exciter exceeds this minimum prescribed level and some form of power attenuation must be used in order to not damage the input of the power amplifier. National RF’s type ATF-3 offers 3 dB of power attenuation (1/2 of the power) when used between the exciter and the amplifier and will handle an input power of 132 Watts, RMS (continuous power) while providing about 66 Watts RMS output power, when it is terminated into 50 ohms. In practice, the ATF-3 attenuator will handle exciters achieving Peak Envelope Power levels (PEP) in the area of 200 to 250 Watts while providing half of that power to the load. For less attenuation requirements, the ATF-1 and ATF-2 offer 1 and 2 dB of attenuation, respectively.
-
Product
Attenuators
-
An attenuator is an electronic device that reduces the power of a signal without appreciably distorting its waveform.
-
Product
90/120 GHz Dual Channel Optical Module
N1032B
Optical Module
The N1032B is a plug-in module for the DCA-X mainframe that includes two optical channels up to 120 GHz.
-
Product
Low Voltage Attenuator
2-20
-
Take advantage of excellent attenuators at a low price. These low voltage units have excellent microwave characteristics and are ideal as an inexpensive low voltage unit for use with our 142 series high voltage precision attenuators while still providing a very respectable and clean 20 ps output risetime.
-
-
Product
Manual Step Attenuator
WATT-3SM352
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customers demand. All Warisons products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
Optics
-
Welcome to Thorlabs; below you will find links to optical components and systems, a subset of our entire line of photonics products. All single element optical components can be found under the optical elements link with the exception of optical components that have polarization properties since they have a separate link. Multi-element systems like beam expanders and objective lenses as well as interferometers, fiber collimators, reference cells, modulators, and other optical devices can be found by choosing the optical systems link. Thorlabs also manufactures an extensive line of free-space and fiber optic isolators; stock items ship the same day that they are ordered while our custom orders benefit from our streamlined design and manufacturing process, which minimizes lead time.
-
-
Product
3-Channel LOW PIM Attenuator
-
Corry Micronics' 3 channel, LOW PIM attenuator covers the 400 to 3000 MHz frequency range and has been specifically designed for major mobile access carriers who are attempting to measure or monitor passive intermodulation distortion/interference in communications systems.
-
Product
Variable Attenuators
-
Variable attenuators are an integral part of most BER testing and EDFA characterization setups. All of EXFO's modular (IQS line) and benchtop variable attenuators are built for top performance and pinpoint accuracy. Each model offers a distinct set of features and specifications to suit various testing needs.
-
Product
Attenuators - Variable / Programmable / Fixed
-
PMI offers a full line of RF and Microwave, Solid State Attenuators that range from a few MHz up to 40 GHz. While we offer many standard models, various options are available. If you do not see exactly what you require on this website, please contact sales@pmi-rf.com because we offer attenuators designed and built to your specifications at catalog prices.
-
Product
SMA Rotary Attenuator
WATT-6SR1211
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
PXI Single 8 Channel Optic Mux FC/PC
40-852-118
Fiber Optic Switch
The 40-852-118 8-channel multiplexer is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
-
Product
Telephone Attenuators & RFI Filters
-
Despite the growth in digital and fiber systems, many telephone companies still require basic line treatment products. Wilcom's hard-to-find line treatment products help the telecommunications industry deliver the performance the customer expects. Products include line powered amplifiers and RFI filters.
