-
product
Managed Ethernet Switch with L2/L3 Layer Support and Fiber Optic Option
ES2
Ethernet Switch module, ES2 provides up to 16 10/100/1000 Base-T 1 Gb ethernet ports. Additionally, there is one 10/100/1000 Base-T maintenance port interface, one RS-232 maintenance/console port interface, and a Fiber-Optic channel with four 10 Gb ports. It also provides numerous L2 and L3 networking, quality of service (QoS) and security features available as described below.
-
product
PXI Dual 2 Channel Fibre Optic SC/PC
40-855-222
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
PXI Single 4 Channel Mux Fibre Optic MU
40-850-314
The 40-850-314 4-channel multiplexer is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
Fiber Optic Power Meters
FOD1204H
The FOD 1204 & FOD 1204H Fiber Optic Power Meters are intended for accurate measurements of up-to-date optical communication. Very small temperature and temporal variations of Loss in Fibers and Connectors. Calibration of Optical Attenuators, Light Sources etc.
-
product
Fibre Optic Converters
In complex testing environments it is often needed that electrical signals have to be transmitted into the chamber or out of the chamber to the test equipment.For that purpose we offer a variety of different interfaces that convert electrical signals into optical signals and back. Such the signal can be transported via fibre optics and is immune against electrical fields.
-
product
Fiber Optic Amplifier
Shanghai Pubang Sensor Co.,Ltd.
1. High response frequency, detect with super high speed2. Suitable for detecting small objects3. Non-contact, non-destructive detection,can be used in harsh conditions4. Simple mounting by DIN connection
-
product
Fiber Optic Components For Optoelectronic Packaging
OZ Optics offers a wide range of standard and custom fiber optic components for optoelectronic packaging. Components include collimators, focusers, patchcords, connectors, and metalized fiber. The low backreflection collimators and focusers are available for a wide range of industry-standard connectors and wavelengths. The hermetically sealable patchcords, with glass or metal solder, and metalized fiber meet high Telcordia standards. The polarization maintaining patchcords and connectors use our specially designed ferrules that minimize insertion loss, backlash, and rotational errors.
-
product
GPIB T8 Cable, 2-Pin Male to 2-Pin Male; Core/Clad 62.5/125 um; 1,300 nm Wavelength Fiber-Optic Cable for GPIB-140A/2 Extender
183164-500
2-Pin Male to 2-Pin Male; Core/Clad 62.5/125 um; 1,300 nm Wavelength Fiber-Optic Cable for GPIB-140A/2 Extender - The GPIB T8 Cable, sometimes referred to as GPIB Cable, connects your system to high-speed GPIB-140A extender devices. You can use the GPIB T8 Cable with a pair of GPIB extenders to increase the cable length of your system up to 2 km without comprising the integrity of your GPIB system or requiring any application modifications. The GPIB T8 Cable is offered in different lengths.
-
product
High-Definition Distributed Fiber Optic Sensing
ODiSI
Luna’s ODiSI system provides the world’s highest resolution distributed fiber optic sensing solution for strain and temperature measurement. Using low-profile optical fiber as sensors, the ODiSI system maps strain and temperature fields with sub-millimeter spatial resolution, providing unprecedented detail and data insight.
-
product
Mini Fiber Optic, Contact, Receiver, Multimode
610113172
* This contact available for purchase as a patchcord only. Choose link below to configure as a patchcord. Primary mating contact 610113173. (May mate with other ITA contacts, as well.)
-
product
Fiber Optic Sensor Head Variations
FU Series
11 Fiber Optic Sensor Head Variations. Flexible Stainless Steel Jacket. Wide Area Detection. Hex-shaped Heads for Trouble-free Mounting. Heat resistant. Small Beam Spot. Thin-sleeve Thrubeams
-
product
Integrated Fiber Optic Rotary Joints
EVERAXIS has more than 10 years of expertise in optical technologies for high data rate signal transmissions. Integrated Fiber Optic Rotary Joints (FORJ) can be supplied as a stand alone product with customized characteristics (wavelength, connectors, fiber characteristics) or combined into a hybrid opto electric slip ring with contact or contactless technology.
-
product
High Power Fiber Optic Visual Fault Locator
VFL-700
Shanghai Fibretool Technology Co.,Ltd.
The VFL-700 is specially designed for field personnel who need an efficient and economical tool for fiber tracing, fiber routing and continuity checking in an optical network during and after installation.
-
product
PLC Fiber Optic Splitter, ABS Box Package, 2.0mm, SC/APC Connector
SUN-PLC 1x2
Guilin GLsun Science and Tech Group Co., LTD
Configuration Type 1x2 Wavelength 1260~1650 nmInsertion Loss 4.1 dB Return Loss 60 dBDirectivity 55 dB PDL 0.2 dBDimension 100*80*10 mm Operating Temperature -20℃ to +70℃
-
product
Protective Cover, Mini Fiber Optic, Receiver
510109501
For use with modules p/n 510104243 and 510104120.
-
product
Fiber Optic Qualification & Dispersion Test Links
8800 Family
Delaire USA qualification test systems are designed to act as worst-case links for bandwidth/dispersion and attenuation, or to meet the customer's loss, dispersion, and distance requirements for custom applications. Because the test links are constructed from hand-selected, industry-standard fiber and not simulated with dispersion elements, all of the effects including loss, dispersion, and fiber nonlinearities are present and authentic. Typical applications include optical transciever testing and qualification for 40G AND 100G systems
-
product
PXI Triple 2 Channel Fibre Optic MU
40-855-332
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
MIL-STD-1553 Fiber Optic Bus Extender
FO-1553
Avionics Interface Technologies
Extends MIL-STD-1553 bus access to over 1 mile for remote access - Dual redundant, single and dual stream options available - Both Transformer and Direct coupling modes supported - Uses fiber optic 1.0625 Gbps data rates for low latency over long distances - Optical signaling is not affected by electrical noise and interference - Simple and easy to use solution, no software setup or configuration required - Ideal for applications where test equipment is separated from UUT
-
product
GPIB T8 Cable, 2-Pin Male to 2-Pin Male; Core/Clad 62.5/125 um; 1,300 nm Wavelength Fiber-Optic Cable for GPIB-140A/2 Extender
183164-100
2-Pin Male to 2-Pin Male; Core/Clad 62.5/125 um; 1,300 nm Wavelength Fiber-Optic Cable for GPIB-140A/2 Extender - The GPIB T8 Cable, sometimes referred to as GPIB Cable, connects your system to high-speed GPIB-140A extender devices. You can use the GPIB T8 Cable with a pair of GPIB extenders to increase the cable length of your system up to 2 km without comprising the integrity of your GPIB system or requiring any application modifications. The GPIB T8 Cable is offered in different lengths.
-
product
Fiber Optic Sensors And Amplifiers
Omron’s high-performance fiber optic sensors and amplifiers come in a wide variety of configurations to meet your specialized requirements.
-
product
Fiber Optic Type Chemical Concentration Monitor
CS-600F
The CS-600F achieves a higher level of functionality best suited for manufacturing, such as the ability to perform in-line measurement of high temperature chemical solutions in various applications, stable operation for reduced downtime, and compact size for improved space productivity in order to meet the precise chemical solution concentration management required in leading-edge semiconductor wet process.
-
product
Single Mode Fiber Optic Rotary Joints
Single Mode Fiber Optic Rotary Joints (FORJ) can be supplied as a stand alone product. Its features can be customized : wavelength, connectors, characteristics of the fiber…
-
product
Mini OTDR Fiber Optic Reflectometer with VFL OPM Laser Source
MT-1300 Plus
Guangzhou Wanglu Communications Co., Ltd.
- Display: 3.5 inch color TFT-LCD screen- Handheld design, light weight and easy operation- Single mode: 1310/1550 nm- Dynamic range: 24 / 22dB (can test about 60 km)- Automatic measurement mode: 1310/1550 nm dual wavelength can be tested simultaneously- Applicable fiber: SM- <8m extra-short event dead zone- Wavelength: 1550nm- Up to 24dB High Dynamic Range- Distance Range: 4,8,16,32,64,128,256km- Pulse width: 3ns-10us- RJ45 cable TDR test & cable sequence test- Optical power meter, Visual fault locator, Laser source- Event Map, can display the length of the link, the type of event point and the position of break point.- USB interfaces, supporting USB stick and printer and direct cable download to PC via ActiveSync- LED light- Built-in friendly-environment lith ium battery with high capacity for over 12 hours of operating life
-
product
PXI Quad 2x2 Fibre Optic Mux MU
40-860-342
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
Fiber Optic Temperature Sensor with the EasyDisk
The TPT-62
The TPT-62 fiber-optic temperature probe family employs industry standard 62.5µm core OM1 fiber optic for highly improved optical, mechanical, and reliability properties over legacy 200 µm core (1st generation) fiber optic sensors. The EasyDisk sensor tip assembly ensures IEC60076-2 (Annex E) compliant installation and enables quick insertion of the probes into the spacers within the windings of transformers.
-
product
Single 2x2 Insert/Bypass F Optic FC/PC
40-820-112
Pickering PXI Fiber Optic Multiplexers connect a single channel to one of two or four channels. They are available in single or dual multiplexer configurations supporting single-mode or multi-mode fiber. A wide choice of connectors types is available. The 40-810 multiplexer connects the optical channel by redirecting the optical signal into a selected output fiber.
-
product
RS-232 Fiber Optic Auto Powered Line Driver
Model 9271
The Model 9271 RS-232 Fiber Optic Auto Powered Line Driver features a standard DB9 interface for maximum performance and reliability of data transmission over glass fiber, eliminating the need for serial to nine-pin adapters. In addition, it brings effective data communications to manufacturing environments. I
-
product
GPIB T8 Cable, 2-Pin Male to 2-Pin Male; Core/Clad 62.5/125 um; 1,300 nm Wavelength Fiber-Optic Cable for GPIB-140A/2 Extender
183164-200
2-Pin Male to 2-Pin Male; Core/Clad 62.5/125 um; 1,300 nm Wavelength Fiber-Optic Cable for GPIB-140A/2 Extender - The GPIB T8 Cable, sometimes referred to as GPIB Cable, connects your system to high-speed GPIB-140A extender devices. You can use the GPIB T8 Cable with a pair of GPIB extenders to increase the cable length of your system up to 2 km without comprising the integrity of your GPIB system or requiring any application modifications. The GPIB T8 Cable is offered in different lengths.
-
product
Fiber Optic Network Simulators
SIM-2FON-25
Vconsole fiber optic network simulator is custom built portable unit intended to simulate installed fiber optic facilities. Vconsole will design and build custom unit exactly to customers specification. The enclosure is capable of housing an individual spool with up to 100km of fiber. We will build each unit to client unique needs with custom fiber types, lengths, and connectors. A full range of connectors are available including SC, ST, FC, and LC types. This product is ideal for latency testing, product development and training and educational needs.
-
product
Single 2x2 Insert/Bypass F Optic FC/APC
40-820-012
Pickering PXI Fiber Optic Multiplexers connect a single channel to one of two or four channels. They are available in single or dual multiplexer configurations supporting single-mode or multi-mode fiber. A wide choice of connectors types is available. The 40-810 multiplexer connects the optical channel by redirecting the optical signal into a selected output fiber.
