DC DC Converters
-
Product
DC Power Module, 20V, 2.5A, 50W
N6733B
Power Module
This module is used in both the small, multiple output 1U high N6700 Low-Profile Modular Power System (for ATE systems) and the multiple output N6705 DC Power Analyzer (for bench testing). GPIB, LAN, USB, and LXI compliance are standard. Select from more than 20 different DC power modules, ranging in capability from basic to high precision, and in power from 20 - 300 W.
-
Product
Multi Output Regulated DC Power Supply
LQ6324T
-
- Low cost general purpose laboratory bench unit.- Fully protected against overload and short circuit.- Three independent outputs electrically isolated from each other.- 5V/5A with over voltage crowbar protection for digital ICs.- Electrically floating outputs up to 500V DC w.r.t. ground.- Compact modular construction.- Precise regulation, low ripple and noise for both constant voltage and constant current operation.- Quality components and conservating ratings for high reliability and long life.
-
Product
USB to Serial Converters, Hubs and Isolators
-
B B SmartWorx powered by Advantech USB products provide plug and play convenience with industrial ruggedness. Look for the orange connector -- you'll find a high retention port that's 50% stronger than a conventional USB port. It won't let go until you want it too.
-
Product
Adapter, 2.4 mm (m) to Type-N (m), DC to 18 GHz
11903A
-
The Keysight 11903A is a metrology-grade, 2.4 mm male to type-N male adapter with dc to 18 GHz operation.
-
Product
Bench top DC Power Supply
R4K-80 Series
-
R4K-80 series is higher performance and next generation model of existing RK-80 series DC variable power supply, which has been receiving good reputation for its innovative compact size and variable range feature. 4-digit meter and high resolution D/A, A/D converters are added newly for more precise setting and reading. Needless to say, the innovative compact size, variable range feature and high operability are remaining same as conventional RK-80. R4K-80 series is the best suitable DC power supply for a variety of applications from laboratory experiment to line productions.
-
Product
High Speed Response, High Accuracy DC Leakage Current Sensor
DCZCT-20CDHL
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Low DC current measurements.*DC1mA～200mA*High accuracy.*±1%F.S ±10mV*Least influence of magnetization.*Less than DC1mA in current level*Convenient +5V single polarity power supply.*Reference voltage (Vref) terminal is equipped.
-
Product
HD Audio Converter Board With Bracket
AX93242
-
*HD audio converter board with bracket*For SBC81205, SBC81206, SHB101 and SHB210*Mic-in/CD-in/Line-in/Line-out/Speaker-out
-
Product
Bench/System/ATE Programmable DC Power Supply Single Or Dual Outputs, 360 To 840 Watts, With Or Without Remote Interfaces
CPX Series
-
PowerFlex design gives variable voltage and current combinations within a maximum power rangeUp to 60 volts and up to 20 amps180 watts or 420 watts maximum per outputIsolated outputs can be wired in series or parallelConstant voltage or constant current operationSettings Locking (S-Lock)PowerFlex or fixed-range operationVariable OVP tripsSelectable remote sense terminalsCompact quarter or half rack 3U case sizeIsolated analogue remote control (CPX400SA only)RS232, USB & LXI compliant LAN (P models only)GPIB Option (P models only)
-
Product
Clamp type AC Current Sensor／with DC Voltage Output
RCT-18
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
Leakage current measurements with DCV output for recorder. AC 0.1mA～100mA.
-
-
Product
FaithTech FTLP Series 100W/180W Portable Programmable DC Power Supply
FaithTech FTLP Series
-
Shenzhen FaithTech Technology Co., Ltd.
FTLP series is a kind of programmable Portable bench DC power supply, with the widest output range, which allows engineers to test more program requirements with just one device. To be exact, the FTLP series provides full power all the way down to 25% of the rated output voltage. The FTLP series is equipped with RS232 and RS485 as standard interfaces that are essential for system integration, you can also choose USB or LAN interface as your add-on interface. The series supports SCPI and MODBUS-RTU protocol, which is convenient for all kinds of test platform. The FTLP series DC power supply can be widely used in battery chargers, high-voltage ultra-high-speed diodes, electrolytic capacitors, electromechanical control fields, and ATE test systems, etc.
-
Product
AC & DC Analog Leakage Meters
507 EL
-
Standard Electric Works Co., Ltd
● Optional for pivot or taut band movement.● Compact and lightweight; easy to use and store.● Mirror scale: for easier viewing & reading.● Built-in stand makes reading and measuring easy.● 200μA full scale value.● Fuse-protected.● Low battery indication.
-
Product
Manual Step Attenuator, DC to 18 GHz; 0 to 70 dB; 10 dB steps
8495B
Attenuator
The Keysight 8495B dc to 18 GHz manual step attenuator offers exceptional repeatability and reliability. Attenuation is provided in 10 dB steps from 0 to 70 dB. Precision gold-plated leaf springs ensure long life (over 5 million cycles) and very high attenuator repeatability (typically 0.01 dB). To improve measurement accuracy, NIST traceable data (SWR and attenuation) is available as Option UK6. Custom step attenuator/switch combinations are possible. The Keysight 11716A/B/C interconnect kits provide quick connection of Keysight 8494/5/6/7 1 dB and 10 dB step attenuators in series for greater dynamic range with 1 dB steps.
-
Product
AC / DC Voltage And DC Polarity Tester
1861
-
Peaceful Thriving Enterprise Co Ltd
*With cETL Approval.*Built-in LED and neon lamp indicator.*Neon lamp for 120V-230V-400V AC.*LED Display for 12V-50V and polarity.*Long lead connects tester body and probe.
-
Product
AC and DC Non Inductive Current Shunt
Series A co-axial shunt and Option 02F/B shunt
-
Use with wattmeters, DMMs and power analyzers to extend current measurement ranges. Use with phase angle meters to enable phase angle measurements between voltage and current. Ultra low phase shift
-
Product
Manual Step Attenuator, DC to 4 GHz, 0 to 110 dB, 10 dB steps
8496A
Attenuator
The Keysight 8496A dc to 4 GHz manual step attenuator offers exceptional repeatability and reliability. Attenuation is provided in 10 dB steps from 0 to 110 dB. Precision gold-plated leaf springs ensure long life (over 5 million cycles) and very high attenuator repeatability (typically 0.01 dB). To improve measurement accuracy, NIST traceable data (SWR and attenuation) is available as Option UK6. Custom step attenuator/switch combinations are possible. The Keysight 11716A/B/C interconnect kits provide quick connection of Keysight 8494/5/6/7 1 dB and 10 dB step attenuators in series for greater dynamic range with 1 dB steps.
-
Product
Coaxial Termination, DC to 2 GHz
909C
-
The Keysight 909C is a precision, low-reflection dc to 2 GHz load for terminating a 50-ohm coaxial system in its characteristic impedance. It is intended for use as a calibration standard. The Keysight 909C may be ordered with an APC-7, type-N male, or type-N female connector.
-
Product
DC Parametric Test System with Curve Trace
DC3
-
The wafer has been fully tested, cut and packaged. Today's IC manufacturers are finding tremendous cost savings in performing just fast DC tests on these packaged parts rather than running the full wafer tests all over again. Until now this required either an expensive full-power IC tester, or a "rack-n-stack" collection of instruments. Enter the HILEVEL DC3 Co-Optive Parametric Tester. No more instruments, no switching matrix, no tricky software. The DC3 combines a high-precision DC-PMU and internal DUT supplies to test up to 2,048 pins, all in a single chassis with Multi-Site capability up to 64 sites. And every DC3 includes our Classic Curve Trace feature, allowing easy curve tracing on every pin.
-
Product
DC Power Module, 100 V, 0.5 A, 50 W
N6736B
Power Module
The N6736B is a one-slot 50 W programmable DC power module for use in the N6700 low-profile Modular Power System or N6705 DC Power Analyzer.
-
Product
Adapter Kit, Type-N and Type-F, 75 ohm, DC to 2 GHz
86211A
Accessory Kit
The Keysight 86211A adapter kit contains three Type-N to Type-F 75 ohm instrument-grade adapters, necessary when measuring Type-F devices on network analyzer with Type-N ports.
-
Product
Catalytic Converter Measurement
OMCAT
-
OMCAT catalytic converter measuring systems provide a fast and efficient means of carrying out complex geometrical measurements on exhaust catalytic converters and of determining the gap bulk density (GBD). OMCAT measuring systems feature innovative measurement functions combined with reliable technology. High measurement speed and accuracy and high availability due to their rugged construction are the major strengths of these systems which come to the fore in the harsh conditions which prevail in production environments.
-
Product
Coaxial Transfer Switch, DC to 26.5 GHz
L7222C
Coaxial Switch
These switches are ideal for manufacturing test engineers working on system integration. Use the Keysight L7222C 4-port coaxial transfer switch in a variety of applications such as a drop-out switch, switching two inputs and two outputs, or signal reversal.
-
Product
Low PIM Coaxial Switch, DC to 26.5 GHz, Transfer
87222R
Coaxial Switch
Low passive intermodulation (PIM) is crucial for applications where two or more transmitted signals share a common antenna or whenever the transmitter signal is too high or the receiver is sensitive to high intermodulation. The Keysight 87222R is a low PIM transfer coaxial switch, operating from DC to 26.5 GHz, which can help to keep the system PIM level low. A guaranteed 0.03 dB insertion loss repeatability and 3 million cycles of operating life ensures signal integrity, improves testing efficiency, and ultimately maximizes test throughput.
-
Product
RS232 / RS485 / RS422 Isolators/ Isolated Converters
-
From 3-wire to 7-wire RS232 isolators, 2-wire RS485 to 4-wire RS422 / RS485 isolators, and USB isolators to USB / RS232 / RS485 / RS422 optically-isolated converters, CommFront has all the industrial-grade optical-isolation devices to protect your assets from the unexpected. If off-the-shelf product does not provide enough security for you, we can even tailor-make the devices, which are customizable right down to the nuts and bolts.
-
Product
Data Converters
-
Omega carries an extensive line of data converters, including RS-232 to USB interface converters, fully isolated RS-232 to RS-485 converters, industrial ethernet to serial device servers, and more.
-
Product
Adapter to Convert (mini-PCI) mPCI
PMC2mPCI
-
Install wireless and other mPCI devices into PMC environments. PMC2mPCI adapts the PMC form factor to mini-PCI type III. PMC2mPCI installs into a standard PMC position - 32 bit PCI bus connectors, standard power and ground, standard standoffs and blank bezel.
-
Product
Solar Array Simulator DC Power Supply
62000H-S
-
Chroma Systems Solutions, Inc.
Solar Array Simulator DC Power Supplies by Chroma provide programmable simulation of Voc (open circuit voltage) up to 1800V and Isc (short circuit current) up to 30A. The 62000S-H series provides an industry leading power density in a small 3U high package. The Solar Array Simulator is highly stable and has a fast transient response design, which are both advantages to MPPT performance evaluation on PV inverter devices.
-
Product
DC Resistance Tester
2511
-
Shenzhen Chuangxin Instruments Co., Ltd.
DC resistance tester. Resistance test range: LW-2511: (10µΩ—2K five shift). Test speed:6 times/fast. Test accuracy:0.2%±2digits。
-
Product
DC Ground Fault Finder
FST-JD200
-
Foresight Electronics Co., Ltd.
FST-JD200 not only can provide a solution on accurately testing the faults of the indirect-grounding of the direct current system, non-metal grounding, loop grounding, simultaneous grounding of the anode and cathode, balanced grounding of the anode and cathode and multi-point grounding 1.
-
Product
1.8-148 MHz Stand Alone Weatherproof Unit for the Application of DC Control Signals up to 400ma on your Coax Cable
Bias-T PLUS
-
The Array Solutions Bias-T PLUS is a 1.8-148 MHz stand alone weatherproof unit that permits the application of DC control signals of up to 400ma on your coax cable. By inserting the control voltage on the coax cable feed-line, you eliminate the requirement for external DC wires for powering remote devices.The Bias-T PLUS weatherproof assembly means that it can be placed indoors or outdoors for maximum flexibility. Typically, one Bias-T PLUS will be placed indoors for inserting DC on your coax feed-line, and one Bias-T PLUS will be placed at the remote device where the DC voltage is extracted.
