PCMCIA Adapters
Adapters that fit in the PCMCIA slot in notebook computers. Different adapters have different functions but they all add connectivity possibilities. (beststuff.co.uk)
-
-
product
RF Adapters
SMA Adapters
Are semi-precision coaxial RF connectors developed in the 1960s as a minimal connector interface for coaxial cable with a screw-type coupling mechanism.
-
product
PCB Adapter, ITA, TriPaddle, 64 Position, To PCB-Mounted 2x34 Pin (BERG 65496-019) Connectors
510108140
The 64 Pin Signal Receiver Module is made from Ryton® R-7 and will withstand temperatures up to 220°C. The 64 Pin Signal ITA Module is made from engineered resin and will withstand temperatures up to 150°C. Both the ITA and Receiver Modules have molded nomenclature.
-
-
product
RF Adapters
BNC Adapters
Amphenol RF offers a wide array of both in-series and between-series BNC adapters in straight and right-angle configurations. 50-ohm and 75-ohm impedance BNC adapters are available with and without panel mounting features. Popular mounting features in bulkhead, both front and rear mount, and 4-hole flange designs. 50-ohm BNC connectors have a frequency range from DC to 4 GHz. 75-ohm BNC connectors optimized for 4K/UHD video applications can perform well to 12 GHz.
-
product
Fiber Adapter
USB Serial Optical Converter
*Optical data transmission*Glass fiber or POF*Optimal galvanic isolation*USB bus-powered*Virtual serial interface*Baud rate up to 115kBit / s
-
product
Test Adapter / Pneumatic Adapter
GPS testing technology offers a wide range of pneumatic adapters. The support with compressed air results in increased ease of use and larger pressures can be built up easily and thus more test needles can be contacted.
-
product
Isolation Adapter
For harsh environments and motor control applications where debug tools may be exposed to high voltage or ground loop potentials, Blackhawk offers two product models of galvanic isolation.
-
product
VoIP Adapter
A VoIP adapter is a protocol converter (bridge) between analog phones and the digital (IP) network that carries voice calls.
-
-
product
Digital I/O Adapter Module For FlexRIO
Digital I/O Adapter Modules for FlexRIO offer up to 54 channels of configurable digital I/O that can interface with single‐ended, differential, and serial signals at a variety of voltage levels. When combined with a large, user‐programmable FPGA, you can use these modules to solve a variety of challenges, from high‐speed communication with a device under test to emulating custom protocols in real time.
-
product
Supply Adapters
AP Series
*Overflow Relative Noise Temperature and Return Loss Measurement within all Frequency Range*Ultrawide Frequency Range*Small Size*4 Design Structures with Different Connector Types
-
product
RF Adapter
Passive coaxial components that are used to transfer signals from one connector interface to another.
-
product
Adapters
A variety of connector types for applications from DC up to 34 GHz!Low insertion lossExcellent return lossFlat responseRugged construction
-
product
High-Stability Adapter
10723A
The Keysight 10723A high-stability adapter converts the 10706A Plane Mirror Interferometer into an 10706B High-Stability Plane Mirror Interferometer. The 10706B is a thermally-stable optic with measurement drift reduced to approximately 1/12 the value achieved by conventional plane mirror interferometers.
-
product
Adapters
They allow a board with either tall components or heat sinks to be placed in a stack of boards in a location other than only at the top. The additional separation is 0.60 inches using standard PC/104-type spacers.
-
product
PCIe Adapter for VPX
PCIe8LSwVPX3U
PCIe8LSwVPX3U is an 8 lane PCIe adapter with switch isolation for VPX development. The switch isolates the spread spectrum clocking found in most PC´s from the VPX port. PCIe 3.0 compliant, 1-8 lanes can be used by the installed VPX.
-
product
RF Adapters
TNC Adapters
Amphenol RF offers a wide array of both in-series and between-series TNC adapters in straight and right-angle configurations. 50-ohm and 75-ohm impedance TNC adapters are available with and without panel mounting features. Popular mounting features in bulkhead, both front and rear mount, and 4-hole flange designs. 50-ohm TNC connectors have a frequency range from DC to 11 GHz. 75-ohm TNC connectors have a maximum frequency of 3 GHz.
-
-
-
product
Test Adapter / Extender
The test adapter is used for measurement and testing of test specimen boards, which gives optimal access of signals, address lines as well as power from backplane assembly.
-
product
PCIe Adapter for PMC
PCIeBPMCX2
Embedded applications frequently require real time processing coupled with special purpose IO. With PCIeBPMCX2´s two positions a PrPMC can be matched with another PMC to make a high bandwidth processing node. The PrPMC can communicate with the host for set-up, and then use the local bus to control and transfer data with the special purpose IO card. For example the PMC-BiSerial-VI-HW1 provides 32 ports of manchester encoded data.
-
product
Waveguide to Coaxial Adapter
D8-AWC84SK-1296
Waveguide to Coaxial Adapter, Frequency 6570~9990MHz, 50W, Rect. Waveguide FBP84, SMA Female
-
product
TTL to RS232 Adapter
SKU-012-XX
The TTL to RS-232 adapter connects the Serial UART to the standard RS-232 port for testing and monitoring functionality. The Adapter facilitates ease of use and helps to reduce board space and cost.
-
product
USB 2.0 Adapter
ADP-USB-445
The ADP-USB-445 USB 2.0 adapter converts one of the USB 2.0 headers on-board the WINSYSTEMS SBC35-427 single board computer to two type-A connectors on the front I/O panel. The integrated circuitry ensures noise immunity from the type-A connections to the single board computer and provides a robust power solution for external devices.
-
product
Solar Connectors & Adapters
Our SOLARLOK photovoltaic connectors are designed for easy, quick and reliable DC connections for solar technology. With a precision-engineered design, these help achieve the lowest contact resistance to reduce power losses. Our DC Plug and splice connectors provide reliable connection, reducing up to 80% installation time with Insulation Displacement Contact (IDC) technology. Our grounding connectors enable installers to ground the photovoltaic system and create flexibility at the installation.
-
product
Run Down Adapters
Testing power torque tools is essential for product quality and regulatory compliance. A run down adapter is designed is to simulate the fastening process of a screw. Mountz run down adapters improve testing repeatability by adjusting for the impact force and irregular peaks of power tools. Mounted in-line between the tool's driver and transducer, a run down adapter provides consistent and reliable torque readings.
-
-
-
product
Pull-Thru Adapters
VPC offers a selection of pull-thru adapters to meet PXI connection needs. Pull-thru adapters consolidate wiring for wired connections and provide a seamless connection to the card for PCB needs.
