Optical Fault Locators
-
product
McMurdo FastFind 220 GPS PLB ( Personal Locator Beacon)
The FastFind 220 Personal Locator Beacon (PLB) uses advanced technology packed into a simple, lightweight, palm sized unit. Using the dedicated 406 MHz frequency, FastFind 220 transmits your unique ID and precise location to the global network of search and rescue satellites. The FastFind 220’s electronics design was upgraded in 2018, offering accelerated location detection with the duel GNSS capabilities — GPS & Galileo recivers. Within minutes rescuers are alerted to your situation, and receive regular position updates. Finally, emergency services can home in on your beacon’s 121.5 MHz transmission to find you. Explore the world with peace of mind. If you find yourself in a remote area without any other form of communication, activating your FastFind 220 will summon emergency assistance.
-
product
Cable Locating Kit
CL-300
The NEW CL300 cable locating kit consists of a portable, holstered pipe & cable locator with an industry accepted 33kHz transmitted frequency. Comes standard with 512 Hz detection capability. With an added 512Hz transmitted device or traceable duct rodder the CL300 becomes the perfect tool for empty duct work locating. This instrument is capable of detecting all electrical, telecommunications and wire circuits—whether direct buried cables or those within conduits—using direct connect or close induction methods. This locator equipment features Auto & Manual adjustments for both transmitter power and receiver sensitivity to assist with a variety of locate work and congestion.Applications
-
product
Static Locator
983v2
The Model 983v2 Static Locator provides accurate measurement of electrostatic charges. Its design enables fast response, low drift and ease of operation. The 983v2 can operate in ?Continuous? or ?Peak Hold? mode to record changes in the level of charge or the highest charge detected respectively.
-
product
Automated Optical Inspection (AOI)
Automated optical inspection (AOI) is an automated visual inspection of printed circuit board (PCB) (or LCD, transistor) manufacture where a camera autonomously scans the device under test for both catastrophic failure (e.g. missing component) and quality defects (e.g. fillet size or shape or component skew). It is commonly used in the manufacturing process because it is a non-contact test method.
-
product
Optical Multimeters
Optical Multimeter integrates both an optical power meter module and an optical light source module and can perform closed-loop tests by using both modules but work individually. It is specifically designed for technical support personnel to test a variety of instruments with a single meter and thus satisfy the user by providing a choice of greater convenience and more advantages.
-
-
product
Optical Tweezers
PicoTweezers
Single or dual beam optical tweezers system based on an inverted microscope • 3D real-time video-based force measurements with sub-pN resolution • Huge free space above optical trap for all kinds of sample chambers and carriers • Manipulate and navigate trapped objects with nanometer precision • Easily extendable to fluorescence, STED, Raman spectroscopy, TIRF, or CLS.
-
product
Hybrid / Optical Dry Mate Connector
The Teledyne ODI Dry-Mate Submersible connector series is designed to directly complement the wet-mate hybrid connector series (Rolling Seal), and also for use as a stand-alone connection system. Two standard shell sizes are available, depending on the circuit configuration. In addition, straight, 45°, or 90° termination versions can be provided. Used in conjunction with Teledyne ODI's oil-filled hose, this system is designed for submersible applications up to 9,100 psi. A unique tri-lobe keying system assures proper alignment.
-
product
Optical Extended CAN Bus Jumper
EOFL-C
Optical Extended CAN Bus Jumper, using fault tolerant to optical conversion to extend the range, can extend up to 5 kilometers subsea.Qualified repeater housing protected on each side by highly reliable glass to metal sealed penetrators.
-
product
Mini Optical Power Meter
FPM-380
Shanghai Fibretool Technology Co.,Ltd.
FPM-380 Handheld Optical Power Meter is a self-developed test instrument. For the installation, operation and maintenance of fiber-optic network is designed as a precise, durable, convenient, portable test instrument. Smart appearance with the backlight, auto-shutdown features, the wide range of optical power testing, test the accuracy of precision as well as a common interface design.
-
product
Intermittent Fault Detection & Isolation System
IFDIS
The IFDIS™ uses patented Intermittent Fault Detector technology that simultaneously and continuously monitors every circuit path within a Unit Under Test (UUT) - such as a Line Replaceable Unit (LRU) chassis' interconnects - for intermittent continuity failures that occur for as short as 50 nanoseconds. This state of the art technology is combined with an environmental chamber and vibration table, which simulate the UUT’s operational environment and cause intermittent faults to manifest, creating a system that is unsurpassed in intermittent fault detection.
-
product
Automated Optical Inspection (AOI)
TR7700 SIII 3D
TRI’s ground breaking 3D AOI solution delivers the fastest hybrid PCB inspection combining optical and blue-laser-based true 3D profile measurement for the highest automated defect symptom coverage possible. Integrated state-of-the-art software solution and third generation intelligent hardware platform offer stable and robust 3D solder and component defect inspection and with high inspection coverage and easy programming.
-
product
Optical Transimpedance Amplifiers
Analog Devices optical transimpedance amplifiers offer a complete, high performance, single chip solution for converting photodiode current into a differential voltage input. Supporting data rates from 155 Mbps to 11.1 Gbps, our transimpedance amplifiers are ideally suited for data communications and telecommunications applications supporting lay protocols including 1×, 2×, 4×, and 8× Fibre Channel, 10GBASE-LX4, SONET/SDH up to OC-192 with FEC, and 10 Gigabit Ethernet. Our transimpedance amplifiers feature low input referred noise current, high input current, and low power dissipation.
-
product
3D Optical Profilers
ZYGO's 3D Optical Profiler instruments enable precise, quantitative, ISO-compliant, non-contact surface measurement and characterization of micro- and nano-scale surface features, capturing up to two million data points in just seconds. Applications range from topography and waviness to roughness and microstructure characterization on samples as that vary from ultra-smooth sub-angstrom optical surfaces, to extremely rough and diffuse 3D printed surfaces.
-
product
Handheld Optical Power Meters
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
Joinwit Handheld Optical Power Meter
-
product
Optical Signal Transmission
Analog
Used for oscillographing analog signals under EFT/EDS/RF interference.
-
product
Fault finder
The STaff™
The staff fault finder is designed to meet the demands of the professional troubleshooter but its simplicity and price make it a tool for anyone needing to locate cable faults. Arrows on the LCD screen direct the user to the fault with pinpoint accuracy. A reference indication also will aid the user in identifying multiple faults when present. Whether you are fault locating utility service line or locating a broken sprinkler wire, the STAFF is the professional's choice.
-
product
Optical Talk Sets
JW4103N
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
JW4103N Optical Talk Set is an intelligent and efficient instrument that combines in one set the functions of both a digital optical phone and a stabilized light source. It is widely used in operations of installation, optical testing, maintenance and fiber attenuation value testing in data network, CATV and Telecommunication network.
-
product
PCI Fault Insertion Switch Range for Differential Serial Interfaces
50-200/201
Pickering Interfaces, a leading supplier of modular signal switching for electronic test and simulation, is expanding its range of PCI Fault Insertion switching with the introduction of two new modules (models 50-200 and 50-201) designed for use with differential serial interfaces. PCI Fault Insertion Switch Cards for Differential Serial InterfacesThe new modules include the Differential PCI Fault Insertion Switch (model 50-200) which is designed for lower data rate serial interfaces such as CAN and FlexRay, and the High Bandwidth Differential PCI Fault Insertion Switch (model 50-201) which is designed for higher data rate serial interfaces such as AFDX and 1000BaseT Ethernet. Each module allows the introduction of fault connections that include data paths open, data paths shorted together, and data paths shorted to externally applied faults such as power supplies and ground. The software driver defaults to a protective mode where conflicting faults are prevented to avoid accidentally shorting unintended paths, such as power to ground. A separate mode allows complete freedom in setting fault patterns.
-
product
PON Optical Power Meter
JW3213
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
JW3213 Series PON Optical Power Meter target at the FTTx application and maintenance. This power meter is able to simultaneously test and estimate the signals of the voice, data and video. It is an essential and ideal tool for the construction and maintenance of the PON projects.
-
product
Optic Node
OX 752
Converts even weak Optic Signals to a high quality RF Signal. LED BAR Optic Level Display has been provided for ease of system maintenance. They are best suitable for Analog as well as Digital transmission to maintain BER, MER Characteristics.- High Quality Nodes- Frequency 40 ~ 1000 MHz- Good Sensitivity of -11 dBm- RF O/P 110 dBµV at 0 dBm Optic I/P- High Voltage Surge Protection- LED Optic Level Display- Powder Coated Housing
-
product
Switchable Optical Interleaver
In a switchable interleaver, there are two operation modes: *Mode A: All pass *Mode B: InterleaverIn Mode A, the system operates at any channel spacing, in which all channels pass through the device and output from one of the two output ports as if there is no extra device inserted. When the system is switched to Mode B, the device operates as a normal optical interleaver, such 50-100GHz interleaver. The working principle is schematically shown below. In Mode B, the device could be a standard symmetric interleaver, or an asymmetric interleaver. Channel spacings are not limitted to 50-100GHz. They can be any frequency pair: between N-GHz and 2N-GHz.
-
product
Fiber Optic Sensor Systems
Fraunhofer Institute for Telecommunications
Fiber-optic and photonic measuring systems open up innovative measuring and control technology concepts for a wide variety of applications. They play a major role in optimizing energy efficiency and are important technological innovation drivers for new and future-oriented markets.In the Department of Fiber Optic Sensor Systems of the Fraunhofer Heinrich Hertz Institute, the focus of application-oriented research is on the development of a new generation of photonic sensors. These are characterized by extreme miniaturization, high network and communication capability as well as extremely low power consumption or even a self-sufficient power supply.In the Department of Fiber Optic Sensor Systems at the Fraunhofer Heinrich Hertz Institute is focused applied research on the development of a new generation of photonic sensors. These are characterized by extreme miniaturization, high network and communication skills as well as an extremely low power consumption, or even a self-sufficient energy supply.
-
product
Handheld Optical Multimeter
JW3209
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
JW3209 Handheld Optical Multimete integrates the functions of an intelligent optical power meter module and of a highly stable light source module in one unit. It can also provide data storage and upload functions. It is widely used in installation ,measurement and maintenance of DDN, Telecom and CATV networks.
-
product
Optical Transmitter
ST1310-XX
Hangzhou Softel Optic Co., Ltd.
ST1310-XX Optical Transmitter adopts high linearity ORTOL DFB laser, build-in perfect pre-distortion adjustment circuit and laser APC,ATC closed loop control circuit. All the operating parameters are controlled by micro-processor, The LCD screen on the front panel can display relative operating status and the fault information.
-
product
Variable Fiber Optic Attenuator
Variable fiber optic attenuator could help simulate distance or actual attenuation in the fiber optic testing work by inserting a calibrated attenuation into the link. By using the variable fiber optic attenuator, technicians could verify the power margin received by testing the fiber optic link power budget. Variable fiber attenuator can help user vary the light power injected from a light source into the optical fiber. Important parameter of variable fiber attenuator include its insertion loss, reflection loss and attenuation range.
-
product
Fiber Optics
The use of fiber optics as light guidance allows great modularity and flexibility in the setup of an optical measurement system. Optical fibers can be made of many materials, such as plastic, glass, and silicates (SiO2). For high-quality fibre optics, as used in spectroscopic applications, synthetic fused silica (amorphous silicon dioxide) is used, which can be intentionally doped with trace elements to adjust the optical properties of the glass.
-
product
Cable Fault Locating Equipment
Commonly used to test underground coaxial and twisted pair cabling, along with transmission lines and other industrial electrical cables.
-
product
PXI-8511, 1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module
780686-02
1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module—The PXI‑8511 is a fault-tolerant Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. The PXI‑8511 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimize message latency and freeing host processor time for processing complex models and applications.
-
product
Sonde Locator
vLoc3-Cam
The vLoc3-Cam is the easiest to use sonde locator on the market today. The omni-directional antenna array allows for approaching the sonde from any position. The directional arrows will guide the user first to the front or rear locate point and then directly to the sondes position. The vLoc3-Cam includes multiple sonde frequencies making it compatible with the major push cameras and crawler cameras on the market. The Pushrod Trace mode shows a second display geared for tracing the path of the pushrod deployed in the pipe or tracing pipes with an optional portable transmitter.
