High Voltage
electric power transmission is > 35,000 volts and for safety AC > 1000 and DC > 1,500. Also known as: HV
See Also: High Voltage Switching, High Voltage Meters, High Voltage Detectors, High Voltage Programmable Power Supplies, HV
-
product
Insulation Testers
Sanwa Electric Instrument Co., Ltd
Is a spot insulation test which uses an applied DC voltage (typically either 250Vdc, 500Vdc or 1,000Vdc for low voltage equipment <600V and 2,500Vdc and 5,000Vdc for high voltage equipment) to measure insulation resistance.
-
product
PPS Clamp Transformer
PPS2 provides power supply to the PD detectors installed on HV cable when low voltage AC power is not available. The PPS2 takes the required power directly from the High Voltage power line under monitoring by means of units clamped on the HV power cable(s).PPS2 is designed to withstand High Voltage line failure events such as temporary overload and short circuit conditions. An internal detection and self limiting circuitry guarantees that PPS2 and the connected equipment survives in case of such events.
-
product
Mobile Testing Power Supply(Microamp)
M8831
M8831 Power supply, a new generation of programmable linear power supply, are designed with high speed dynamic programming output(Voltage 0-30V, 1ms rising time), high current accuracy (0.001mA resolution) and low internal resistance, which can satisfy all the test requirements. The combination of bench-top and system features in these power supplies not only make it possible to option into other equipments, but also make it possible for users to edit program by panel keyboard, which will bring much convenience to users. Meanwhile, the voltage level switch works without relay, which will cause the fast switch between high voltage and low voltage. Moreover, M8831 powr supply provides the best solutions for cellphone research, micro-electronics lab,research institue and special users requiring power supply with low current buthigh accuracy .
-
product
DC High-Voltage Test Device
PGK 80
BAUR Prüf- und Messtechnik GmbH
Cable testing and diagnostics with the BAUR PGK 80. The portable, one-piece PGK 80 high-voltage test device for generating negative DC voltage up to 80 kV is primarily used for onsite testing of paper-insulated mass-impregnated cables in the medium-voltage network. The high voltage is generated through a high-voltage transformer with secondary voltage-multiplier. The internal operating frequency of 20 kHz enables the smallest of device dimensions.* Continuous adjustable output voltage* The voltage measurement is done directly at the high voltage output* Timer of 1-30 min* Sensitive current measurement for recording the smallest of insulation currents with 6-time range switch, decadal
-
product
Embedded Synchro - Resolver -
LVDT I/O Cards
Computer Conversions Corporation
100% Transformer Isolation is offered for all AC I/O, and various Isolated DC converters are available as standard product, eliminating concerns for ground-loops, ground interjected (intermittent and ghostly) field noise, inductive surges, differing potentials, and high voltage field transients from effecting the card itself, the sensitive ISA bus backplane and any other device or system sharing these signals.
-
product
Active Differential Probe
DF-600
The DF-600 Differential Active Probe is a high input impedance and low input capacitance probe. It also supports extremely high frequency bandwidth, and high voltage input. It is designed using three OP amps, namely two FET buffer OP amps and a low offset OP amp. Therefore, even with long-term operations, the measured voltage will not drift. The voltage offset always approach 0 volts. (USB power supply should be 5V ±2%). The following diagram shows the circuit of DF-600.
-
product
Pre- Locator
CFL PL4
CFL PL4 Power Cable Fault Locator is a portable, easy to use cable fault pre-location instrument. It uses the Time Domain Reflection (TDR), Secondary Impulse Method / Multiple Impulse method (MIM) and Impulse Current Method (ICM) on low, medium and high voltage cables. Its measuring ranges enable pre-location on cable lengths from 500 m to 64km.
-
product
SpectroMax
El-Mul’s proprietary technologies enable unique solutions for compact BSE energy spectrometers. El-Mul’s unique high-resistivity coating stands at the forefront of our energy filtering detection platform. This unique coating is key for high voltage holding over short distances in vacuum.
-
product
Solidtron Thyristors
The Solidtron family of products employ our advanced high voltage thyristors having incredibly fast and predictable turn-on performance as well as remarkably low conduction loss. These key attributes make Solidtron products ideally suited for use in a wide variety of pulsed-power applications where precise turn-on characteristics, reliability and longevity give them distinct advantages in certain applications over tube and spark-gap technology.
-
product
Partial Discharge Test Equipment
Wuhan Huatian Electric Power Automation Co., Ltd.
Partial discharge detectors for high voltage equipment.
-
product
PXI Solid State Very High Density Matrix
40-501-001
The 40-501 is a very high density matrix using solid state switching configured as a 64x4 1-pole matrix in a single slot 3U PXI module. It is ideal for applications requiring fast operation and a long service life with frequent switch operations at high voltages. Since the design is based on solid state relays the matrix has no wear out mechanism.
-
product
LXI High Voltage Matrix 2-pole 200x2
60-310-202
The 60-310 is a 2-pole Matrix Module available in 300x2, 200x2 and 100x2 formats. It is capable of cold switching 1000VDC and has a maximum carry current of 1A. It is designed for high voltage applications including circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing.
-
product
Cable Assembly, 37-Pin D-Type, Male to Unterminated With Ferrules, 0.5m, HV
40-972-037-0.5m-MU-HV
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
Series Standard HV Capacitors
PMT10000
Power Measurement Technologies Inc.
High voltage, low dissipation factor, gas-filled Standard Capacitors for indoor use in a laboratory or production environment. A three terminal design configuration allows accurate measurements of capacitance and dissipation factor (tangent delta) with little or no effect from test lead or stray capacitance.
-
product
High Voltage Optically Isolated Probe, 350 MHz Bandwidth. Includes soft-carrying case.
DL03-ISO
The DL-ISO enables highest confidence in GaN and SiC device characterization with highest accuracy, best signal fidelity, and comprehensive connectivity.
-
product
sbRIO-9215, Non-Enclosed, ±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Modul
780878-01
Non-Enclosed, ±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The sbRIO‑9215 performs differential analog input. The sbRIO‑9215 contains NIST‑traceable calibration, a channel‑to‑earth ground double isolation barrier for safety and noise immunity, and high common-mode voltage range. Non-enclosed modules are designed for OEM applications.
-
product
High Voltage Power Supplies
FuG high-voltage power supplies of all types except HYN are primary switched-mode power supplies with pulse width modulation . The rectified mains voltage is chopped into square pulses of constant frequency, transformed, rectified and smoothed. The square-wave voltage is pulse-width modulated for regulation.
-
product
9-Pin D-Type, Right Angled PCB, Male,HV
40-963-009-RM-HV
9-Pin Male Right Angled D-Type Connector, High Voltage - PCB Mount
-
product
PXI Digital to Analog Converters
Keysight's PXI digital to analog converters and V/I sources are capable of supplying high and low voltages levels as well as source currents on one or multiple channels.
-
product
Replacement Pincer Clips for High Voltage Differential Probe
PK-HVA-02
Replacement Pincer Clips for High Voltage Differential Probe
-
product
PXI/PXIe High Voltage Multiplexer, Single 48-Channel, 1-Pole
40-321-109-HI
The 40-321-109-HI (PXI) and 42-321-109-HI (PXIe) are single 48-channel 1-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
product
50 Ω High Voltage Pulse Generators
High Power Pulse Instruments GmbH
50 Ω High Voltage Pulse Generators by HPPI GmbH
-
product
2100Vdc Screw Terminal Connector Board | Cable & Harness Tester
CB29H
CAMI Research Inc. (Acton, MA) announces another new board for its CableEye cable and harness testing systems. Populated with four 16-pole screw terminal blocks, the board addresses high voltage (HiPot) testing to 2100Vdc/1200Vac. Of particular interest to the harness testing market, the CB29H is also available as a transition board variant (CB29AH). The CB29H and CB29AH boards are high voltage versions of the CB29 with the high voltage traces running on inner layers to afford additional safety, and protection from contamination.
-
product
Insulation Resistance Testers
Shanghai Beha Electronics Co., Ltd.
*This is a variable high voltage insulation tester from 500V to 15kV in 500V steps.*The is menu driven and uses Dynamic Current Auto ranging technology.*It has a Bar-Graph which displays the voltage stressing the insulation while the test is in progress and the voltage decay during the automatic discharge of the tested circuit.*The top line of the display shows the elapsed time at the start of the test. Digital readout of the total time will remain displayed even after testing has ceased.*A 4-digit display (2000 counts) is showing the actual insulation resistance.*This instrument displays a voltage warning and sounds when AC or DC is present before injecting the test voltage.
-
product
Digital Teslameters/Gaussmeters
S Digital Teslameters offer accurate, high resolution measurement of magnetic flux densities, withdirect digital readout in tesla or gauss, and serialcommunications by fiber optics or RS-232C for system applications.The instruments are light and compact, and the probes are easy to use. The DTM-151 has been engineered to withstandthe severe electrical interference produced by high voltage discharge.
-
product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Tinned Ends, 0.5m HV, Exit Towards Pin 1
A050DF5-T-HA050
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
Short Hot Stick
HS-800
Standard Electric Works Co., Ltd
● Single foamed hot stick.● Universal sunrise fitting on the head to fit special tool fittings.● Rated at 100 kV per 300mm (5 minutes).● Can be connected to 275 HP HV proximity detector, 21X HVD capacitive HV detector and 277 HP Non-contact HV detector.● Meets IEC 60855.● Reasonable price.● Accessories
-
product
Hi Pot Meters
The HI Pot Device is designed to Hi Pot de-energized 15kV class cables. The tool transforms 18 Volts from the battery to approximately 8,000 volts DC. When the battery is installed and the safety switch is in the closed down position, the unit is in voltage detection mode. The unit should be in this position when installing the device, as it will sound a warning alarm if you approach an energized source. When the safety switch is lifted and the toggle switch is switched up, the unit is in the Hi-Pot mode and the high voltage DC is being applied.
-
product
Portable Hardness Tester
Sinowon Innovation Metrology Manufacture Ltd.
◆ Metal shell, nice appearance design.◆ Available to save 2000 groups test results.◆ Support hardness conversion among HRC, HRA, HRB, HV, HB, etc, can convert 2 different scales simultaneously.◆ 4” LCD to display hardness result, conversion results, Max, Min,Mean value;◆ Support blue tooth printer, with RS232 to connect computer for software running;◆ Can test all kinds of metal which more than 5kg;◆ Indicating error ±5HLD, conform standard ASTM A956;◆ Support 7 types of impact devices.
-
product
High Voltage Insulating Diagnosis Systems
DAC-6017
It can measure and diagnose the insulating characteristic of winding coils of high voltage electric motor, generator, and etc.It also makes possible to build in-vehicle type or stationary type in accordance with the application.
