High Voltage
electric power transmission is > 35,000 volts and for safety AC > 1000 and DC > 1,500. Also known as: HV
See Also: High Voltage Switching, High Voltage Meters, High Voltage Detectors, High Voltage Programmable Power Supplies, HV
-
product
50-Pin D-Type Male with Backshell, HV
40-960-050-M-HV
This connector is designed to allow users to directly terminate cables with soldered connections.
-
product
LXI Single 75x4 2-Pole HV Matrix
60-311-001
The 60-311 is a 2-pole Matrix Module available with one, two or three separate 75x4 matrices housed in the same case. It is capable of cold switching 750VDC continuous with a carry current of 2A plus higher pulse conditions e.g. typically 1000VDC for 1s with low duty cycle or 6A for 200us with <1% Duty Cycle.
-
product
MPOD Crate
WIENER presents with Mpod a new, universal multi-channel low voltage (LV) and high voltage (HV) computer controlled power supply system. Offering highest channel density the MPOD mainframe can house up to 10 plug-in modules which results in 80 up to nearly 500 individually controlled channels per mainframe. Built in a modular way MPOD consists of the mainframe / bin, a front side plug-in controller with Ethernet and USB ports, a fan tray and a power supply which is located in the back.
-
product
ATE For ADC Module
MS 1527
The Semi-ATE is used for testing the analog ADC. It shall carry out the functional test on ADC analog module. The ATE shall have all necessary IO signals on the connector end. The semi-ATE can carry out the functional tests on ADC analog module with host PC or laptop. It provides +15V, -15V, +5V & -5V to module and +2.5V high precision reference voltage. It can able to control keysight N6700B Power supply mainframe using RS422 interface.
-
product
Surge Generator
Techno Instrumentation (India) Private Limited
LT to HT 11 kV and 33kV Surge Generator is an all in one solution for thumping, DC high voltage testing(Hipot-test) and burning for effective fault location in LT to HT 11 kV and 33kV cables.
-
product
Multiplexer
SC6540
Our patented SC6540 modular scanning matrix pioneered the largest productivity improvement in the electrical safety compliance industry in years. With up to 16 independent high voltage or high current channels in a convenient 2U design, the SC6540 can be customized in 10 different configurations for multi-point Hipot, Ground Bond, Insulation Resistance and Leakage Current testing.
-
product
Impulse Winding Tester
TH2883S8-5
Changzhou Tonghui Electronic Co., Ltd.
TH2883 series products are newly developed impulse winding testers by Tonghui. This product line makes Tonghui as the first provider of impulse winding tester from low voltage of 30V to high voltage of 10kV, single channel to multichannel (Max.:8 channels) in this industry. The instrument adopts popular 32 bit CPU and high density SMD technology, 65k color 7-inch TFT wide display screen, bringing ease for your eyes and convenience to your operation. The impulse voltage of100V~5000V, maximum 8 channel sweep test, maximum 20 test procedures, sampling rate of 200Msps, memory depth of 6k bytes makes your test accurately.The usage of standard sample average, application of demagnetized impulse, high bandwidth analog acquisition circuit, technology of high-fidelity corona extraction as well as the opening of non-destructive test reflect the design philosophy “customer-oriented, share the future technology with you” of Tonghui.
-
product
Cable Assembly, 37-Pin D-Type, Male to Unterminated With Ferrules, 1m, HV
40-972-037-1m-MU-HV
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
Automatic Capacitance Bridge Tester
HTDR-H / 395
Wuhan Huatian Electric Power Automation Co., Ltd.
Measurement of high voltage shunt capacitor banks for reactive power compensation devices.
-
product
HV Enclosures with Integrated Safety Test
The HV test hood according to Performance Level e (ISO 13849-1), developed by us according to the EN50191 standard (erection and operation of fixed and temporary electrical test installations), offers the highest safety for the operator. The large test chamber is enclosed with a hood made of sturdy, highly insulating and transparent plastic. During the test, there is a clear view of the test specimen. A signal light visually indicates safe opening when the light is “green”. “Red light” symbolises danger, the hood cannot be opened due to the safety interlock. The safety switch also ensures that the hood cannot be opened during the test. This means that the test hood fulfils all the required specifications for compulsory contact protection.
-
product
PXI Dual Programmable +10V Power Supply
41-735-001
A single slot power supply module providing two programmable positive output voltages. The module provides high quality regulated voltages from a linear regulator to ensure low levels of output noise.
-
product
Cable Assembly, 9-Pin D-Type Female to Unterminated With Cut Ends, 0.5m, HV
A009DF4-C-HA050
A range of 9-Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation.
-
product
HIPOT Insulation Testers
Crown high voltage, transformer type hipot insulation testers are safe, easy to use for quick, positive determination of grounds, shorts, and broken wires in motors, transformers and other low voltage equipment or wiring systems. A turn of the selector switch gives a selection of seven voltages; 500, 1080, 1250, 1500, 1750, 2000 or 2500 volts calibrated to +/- 5% accuracy; NEMA recommendation for insulation test is twice normal voltage plus 1000 volts. Since this instrument has a capacity of 2500 volts, it readily accommodates all normal requirements.
-
product
120 A High Voltage 50 Ω Pulse Generator
TLP-12010C
High Power Pulse Instruments GmbH
- High pulse output current up to 120 A (short circuit)- Ultra-fast 50 Ω high voltage pulse output with typical rise time 100 ps (0 A to 40 A) and 300 ps in high-current mode (0 A to 120 A)- Wafer, package and system level TLP, VF-TLP and HMM testing- Up to 180 kW peak output power into 50 Ω load- Built-in HMM pulse up to ±32 kV in 50 Ω-configuration- High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)- 6 USB programmable pulse rise times: 100 ps to 50 ns (custom selectable)- 8 (optional 9) programmable pulse widths: 0.5 ns (optional), 1 ns to 100 ns (0 A to 40 A), 1 built-in pulse width: 100 ns (>40 A)- The optional pulse width extender TLP-3011C enables pulse width up to 1.6 µs in 68 GPIB programmable steps (0 A to 40 A)- Optional external pulse width extensions from 5 ns to 500 ns (>40 A to 120 A)using the external pulse width extender TLP-12012A6- Built-in pulse reflection suppression- Fast measurement time, typically less than 0.2 s per pulse including one-point DC measurement between pulses- Efficient sofware for system control and waveform data management- The sofware can control automatic probers for fast measurements of complete wafers- Combines TLP-12010A and TLP-4010C into one system- Can be operated together with TLP-12012A6 and TLP-3011C pulse width extenders- Integrated interlock safety shut-down- Industrial isolated and EMI/ESD protected USB control interface
-
product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Tinned Ends, 1m HV, Exit Towards Pin 1
A050DF5-T-HA100
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
High Voltage Amplifier
HA-205
*2500V/uS Super High Speed Model *170Vp-p (±85V DC) *900mAp-p (±450mA DC) *Bandwidth: 3MHz / 100Vp-p *Gain (AMPL): 0~35 (10 Turn VR+SW) *Microprocess Control Protection
-
product
PXI/PXIe High Voltage Multiplexer, Single 23-Channel, 2-Pole
42-321-127-HI
The 40-321-127-HI (PXI) and 42-321-127-HI (PXIe) are single 23-channel 2-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
product
Universal Multichannel System up to 100V
- From 12 to 48 independently controllable High Voltage channels- 0 ÷ 100 V output voltage- Maximum Current: 1mA, 10 mA or 1 mA/100 μA (dual range board)- Individual Enable (A1510 only)- Either DB37, DB25 or SHV connectors- Available with either positive, negative or mixed polarity- Up to 20 nA / 100 pA current set / monitor resolution- Up to 2 / 0.2 mV voltage set / monitor resolution- Extreme Low ripple, down to < 3 mVpp- 3 different channel grounding- Common Ground (AGxxxx)- Common Floating Return (Axxxx)- Full Floating (A1510 only)- Independently programmable for each channel:- Output voltage- Current limit- Ramp up/down- TRIP parameter- Current generator operation in overcurrent condition- Specific design for double side silicon detector (A1510)
-
product
Digital Clamp-on DC/AC AMmeter / Multimeter
HH2009
Large LCD display 6000 count with symbolic signs. Auto Ranging High Voltage test up to 600V DC and 600V AC. Higher Current test up to 600A AC/DC. Continuity check. DC A zero adjust function. Low Battery Indication. Data Hold and Auto-Off Function
-
product
Bluetooth Enabled Signal Conditioners I/O Modules
microBlox
Acromag's microBlox uB Series I/O modules offer a compact, high-performance solution for interfacing sensors and field devices with data acquisition systems. uB signal conditioning modules are ideal to isolate, filter, convert and amplify a wide variety of signal types for test, measurement and control systems. Just plug uB modules into 4, 8, or 16-channel backpanels in any mix for a high-density analog I/O interface. Channel-to-channel isolation provides optimal noise and surge protection from ground loops, spikes, and high common mode voltages.
-
product
6-1000V AC/DC Multi-function Voltage Tester
7340
Peaceful Thriving Enterprise Co Ltd
1. AC / DC Polarity Measurement2. Voltage Measurement3. High Voltage Indication4. Phase Rotation Test5. Non-contact Voltage Sensing6. Continuity Test7. Illumination
-
product
HV-Test System for Capacitor Packages
The system is used to characterize the leakage currents of capacitor packages. LXinstruments implemented a project-specific PCBA for the required HV switching. The measurement technology consists of Keithley source meters and USB based devices. The DUT adaptation with safety technology was realized in cooperation with ATX.
-
product
12-690V Voltage Tester With LED/LCD Display
7339
Peaceful Thriving Enterprise Co Ltd
Measurement by LED Display1. Double-pole Test2. High Voltage Indication3. Phase Rotation Test4. Polarity Indication5. Continuity Test6. Illumination
-
product
Cable Assembly, 9-Pin D-Type Female to Unterminated With Tinned Ends, 0.5m, HV
A009DF4-T-HA050
A range of 9-Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation.
-
product
Surge Generator
CFL SG 3210
SCOPE offers CFL SG 3210, Surge Generator with output of 32kV and 1000 Joules. It is ideal choice for fault location on all types of power cables from LV to EHV. CFL SG Series is equipped with different Protections, Interlocks and Auto-discharge Facility to ensure User Safety during operation. User Friendly controls, adequate form factor, contact free HV terminations makes this CFL SG Series most durable and best-designed sets in the segment.
-
product
PXI 64-Channel Digital Output Module
40-412A-021
The 40-412A-021 (PXI) and 42-412A-021 (PXIe) are 64-Channel Digital Output modules with high output voltage and current capability. The outputs can be used for high or low drive and each channel is capable of sourcing 0.5A from the high side or 0.5A sink on the low side. Accidental operation of both high and low side driver on the same channel is prevented by the supplied driver. Outputs are fully protected against over-voltage, over-current and thermal overload, ensuring robust and reliable operation in the toughest test environments. For high side driving, the voltage source is supplied externally, allowing the module to drive high capacity loads separate from the chassis power supply. For low side driving, the external source is not used and the module’s output operates an open collector or open drain driver.
-
product
HIPOTS (High Voltage Testers) / AC Hipots
5 kV Digital
UDEYRAJ ELECTRICALS PRIVATE LIMITED
Panel mounted controls & indicators. Variable from zero to 5 kV. Digital kV and leakage mA meter.
-
product
L.V. Current Transformers
ENTES LV Current Transformers are measuring transformers which transform the primary current by a specified ratio to its secondary side with a phase difference of 0 degrees. They provide isolation of the relays and measuring devices from the HV side of the network.
-
product
PXI Solid State Very High Density Matrix
40-501-001
The 40-501 is a very high density matrix using solid state switching configured as a 64x4 1-pole matrix in a single slot 3U PXI module. It is ideal for applications requiring fast operation and a long service life with frequent switch operations at high voltages. Since the design is based on solid state relays the matrix has no wear out mechanism.
-
product
NI-9205, ±10 V, 250 kS/s, 16-Bit, 32-Channel C Series Voltage Input Module
779357-01
±10 V, 250 kS/s, 16-Bit, 32-Channel C Series Voltage Input Module - The NI‑9205 performs single-ended or differential analog inputs, with four programmable input ranges for each. It is an effective combination of channel count and speed at a low price for an economical multifunction system. You can choose from four programmable input ranges. To protect against signal transients, the NI‑9205 includes up to 60 V of overvoltage protection between input channels and common. In addition, the NI‑9205 also includes a channel-to-earth ground double isolation barrier for safety, noise immunity, and high common-mode voltage range. It is rated for 1,000 Vrms transient overvoltage protection.
