Modbus
communications protocol for sharing data between controllers.
See Also: Communication Protocol, Near Field Communications, Data Communications, Modbus RTU
-
product
Modbus Utility
A test tool of Modbus connection. Support Modbus TCP, Modbus RTU, Modbus ASCII connections. Support Modbus Functions: 01: Read coil status. 02: Read input status. 03: Read holding register. 04: Read input status. 05: Write single coil status. 06: Write single holding register.
-
product
Modbus Simulator
Modbus Slave
Modbus Slave is for simulating up to 32 slave devices in 32 windows!. Speed up your PLC programming with this simulating tools. Start programming and test before you receive your slave device from supplier.
-
product
Programmable Modbus Simulator
ModMultiSim
ModMultiSim is a programmable Modbus simulator that enables realistic simulation of multiple Modbus slaves in their environment. Connect your Modbus masters to ModMultiSim, instead of real Modbus slave devices, in order to test and configure the masters.
-
product
Wireless Modbus Sensors
Wireless Modbus Sensors & Condition Monitoring – The Best of 2 Worlds! Combining Phantom Wireless Sensors with an Industry Standard such as Modbus! The best in Vibration monitoring equipment!!
-
product
Modbus Transmitter for LPPHOT01 Probe
LPPHOT01S
The transmitter LPPHOT01S converts the mV analog signal generated by the illumination probe LPPHOT01 into a digital signal suitable to be transmitted over a serial line RS485 with MODBUS-RTU protocol.
-
product
BACnet / Modbus
BACnet™ MS/TP and Modbus RTU communicating sensors provide an easy-to-install and cost-effective means to measure temperature and humidity anywhere on your network. They’re especially effective where there is limited controller inputs or the application is for monitoring only. All BACnet™ sensors are BTL Certified.
-
product
Modbus Diagnostic Program
Modsak
Modsak is a versatile Modbus diagnostic program. It will be of interest to device manufacturers, software developers, system integrators and field service engineers. Modsak can be used to test or simulate almost any device or system that uses the Modbus protocol: slave devices, PLC's, HMI's, MMI's, DCS's, RTU's, SCADA systems, bridges, gateways, device servers, etc.
-
product
Modbus High Accuracy Fixed Flowmeter
D118i
Gentos Measurement & Control Co.
D118i is an advanced flow meter, which applies our patented PICOFLOY technology, with ultra-high accuracy, linearity, and repeatability, and meets the high measurement accuracy requirements of users.
-
product
Modbus Diagnostic Master
ModMaster
ModMaster is a diagnostic program that operates as a Modbus master or client. It provides all the features of Modsak's master modes, but at lower cost.
-
product
Ethernet To Modbus RTU Interfaces
ICS's Ethernet to Modbus Interfaces provide Modbus TCP/IP to Modbus RTU serial conversion and Raw Socket (Telnet) to control Modbus RTU Slave Devices. Available in small Minibox™ and OEM board formats. OEM board has Ethernet, GPIB and USB interface ports. All Interfaces include the VXI-11 protocol for use with: LINUX, UNIX, SunOS, Apple OS X, HP-UX, IBM-AIX and Windows 2K or later Windows systems.
-
product
4DI/4 Relay Output Modbus RTU Remote I/O
ND-6160
The NuDAM modules provide direct communications with a wide variety of sensors; perform signal conditioning, scaling, linearization and conversion; can acquire measurements of temperature, pressure, flow, voltage, current; and handle multiple digital signal types broadly used in IoT and other industrial applications, such as facility monitoring, environment monitoring, and industrial process control. The new ND-6117, ND-6124, ND-6150, and ND-6160 modules feature Modbus/RTU as the best remote data transmission protocol, which provides customers a comprehensive product offering.
-
product
Modbus Register Converter - Serial To Modbus RTU Interface
Translates Modbus registers and variable types from an older Modbus devices to a new Modbus device. The Model 2390 allows upgrading Modbus RTU devices without changing the system software. The 2390 also provides serial control of Modbus RTU devices for new applications that want the ease of using simple ASCII commands strings when controlling Modbus RTU devices.
-
product
Modbus RTU Analog Input
Provide direct connection to a wide variety of sensors to any host with an RS232 or RS485 port. The modules perform all signal conditioning, scaling, linearization, and A/D conversion. They each contain some discrete digital I/O lines and can measure signals such as:
-
product
Modbus Analog Output Modules
DAT3020 Series
The DAT3020 series from Datexel is a range of Modbus analog output cards. These cards or modules have both voltage and current outputs either 0-10V or 4-20mA and are isolated from the input, output and power supply. They are available with either 2, 4 or 8 channels. The DAT3011 is a Modbus slave with 2 analog inputs (Thermocouple, RTD's mA, Resistance, Potentiometers, mV and voltage) and 2 analog outputs(4-20mA). It also has 3 digital inputs and outputs. Combining these analog output cards with the analog input cards, and the digital IO cards with the DAT9000 controllers make Datexel the smart choice where Data Acquisition is needed.
-
product
Modbus Stack
softMOD
SoftMOD is the industry-standard Modbus protocol stack for industrial automation and building management. SoftMOD supports both Modbus RTU (Remote Terminal unit) and Modbus TCP/IP (Transmission Control Protocol) as well both client and server modes.
-
product
Modbus/TCP Gateway
MODG-100
MODG-100 is a Modbus/TCP to Modbus RTU gateway. Itfeatures one serial port which can be configured as either RS-232, RS-485 or RS-422 and an Ethernet port. It can be mounted on a DIN rail.
-
product
Modbus Slave Simulator
ModSim
ModSim32 is a very simple but powerful application for simulating data from modbus slave devices. ModSim is an MDI application which allows you to define multiple blocks of data points which may then be accessed from a connected modbus master.
-
product
MCCI Catena® 4470 Modbus Node For LoRaWAN™ Technology
The MCCI Catena® 4470 Modbus Node for LoRaWAN™ technology is a powerful open-source IoT device that integrates Modbus control with The Things Network. Based on the Adafruit Feather M0 system, the Catena 4470 is a ready-to-use platform for Modbus-oriented LoRaWAN 1.0.2 and 1.1 wireless IoT applications.
-
product
N- Dual Channel Multiparameter Analyzer w/ Modbus
MemoRail Modbus A1405
With the increasing demand for a compact and flexible solution to liquid analysis –ALVI Technologies has responded with a new twist in the existing MemoRail. We are pleased to announce the release of our new MemoRail Modbus A1405 N- Dual Channel Multiparameter Analyzer with Modbus that offers an optimal solution for integrating a compact, flexible, all digital analyzer in an extremely cost-effective manner!! Our Dual Channel Multiparameter Analyzer with Modbus can be used with Memosens and digital sensors such as pH (glass and IsFET), ORP (redox), oxygen, and conductivity (conductive and inductive). It’s also the only analyzer in its class that is suitable for use with a digital optical oxygen sensor. All sensor types can be used in any combination in the dual-channel version.
-
product
Modbus RTU Rs486/232/422
It provides client/server communication between devices connected to different types of buses or networks. Modbus-RTU (Remote Terminal Unit) means that the Modbus protocol is used on top of a serial line with an RS-232, RS-485 or similar physical interface.
-
product
Modbus Master Data Scanner
ModScan
ModScan is a Windows application which operates as a modbus master. It allows you to access and change data points in a connected slave device using either the RTU or ASCII Transmission mode. ModScan is ideally suited for quick and easy compliance testing of the modbus protocol and its built-in display of serial traffic allows effective troubleshooting of field connections.
-
product
Modbus Data Logger
Mod Bus is a popular protocol that is used by manufacturers of instruments and sensors. Site instrumentation already exists and parameters to be recorded are available on Mod bus. We have in store fro our clients Mod bus Data Logger that can read data from these instruments and record them periodically. These loggers are configured as per the site requirements.
-
product
Modbus to Profibus Converter
P485
The P485 Modbus to Profibus Converter acts as a gateway between a Modbus RTU network and a Profibus-DP network. Integration of Modbus devices into Profibus networks is enabled without loss of functionality, control, and reliability, both when retrofitting to existing equipment as well as when setting up new installations. The P485 Modbus to Profibus Converter is an external DIN-rail mounted device which provides Profibus network connectivity to Modbus devices via a serial RS232/RS422/RS485 interface.
-
product
Modbus RTU Analog Input Modules
The Datexel range of Modbus RTU analog input cards for both RS485 and RS232 with Modbus or ASCII protocol can be combined with the DAT9000 series of Modbus Masters. A choice of input cards or modules are available and have various optional inputs such as Voltage, Current, Thermocouples, RTD, and Resistance. Also a choice of 2, 4, 8 channel options are available. The DAT3011 is a Modbus RTU Slave with 1 selectable universal input (Thermocouples, RTD, mV, RTD's or Resistance), 2 x 4-20mA or 0-10V input and 2 x4-20mA outputs. The DAT3011 also has 3 digital inputs and 3 relay outputs. Each module is isolated from each other and is set up using the DAT3000 software Development package which is free of charge from the Datexel download web page. Datexel also has universal input modules. An 8 channel analog input card is available making the DAT3000 series a very economical solution to large and small scale Data Acquisition. Combining these analog input cards with the analog output cards, the digital input/output cards and the communication devices make Datexel the smart choice where Data Acquisition is required.
-
product
Modbus Master TCP/IP Component for .NET
WSMBT
WSMBT is a powerful and simple to use .Net component that makes it easy to access data from a Modbus slave device connected to the PC's Ethernet network. Simply drop the component on your form and talk to your device with your VB.NET, C# or Managed C++.
-
product
Modbus to DeviceNet Converter
D485
The D485 Modbus to DeviceNet Converter acts as a gateway between a Modbus RTU network and a DeviceNet network. Integration of Modbus devices into DeviceNet networks is enabled without loss of functionality, control, and reliability, both when retrofitting to existing equipment as well as when setting up new installations.
-
product
Modbus Transducers
THI Sensors
The THI-485 sensors are Modbus transducers for measuring thesurrounding temperature and relative humidity or for theacquisition of up to four passive pulse signals or digital states. This feature extends the possibilities of the device, turning it into a kind of RS485 pulse concentrator from other sensors andmeters.
-
product
Ethernet-GPIB-USB to Modbus RTU Interface
Model 9009
* All interfaces provide full control of the Modbus RTU slave devices.* Ethernet port supports VXI-11, raw socket and Modbus TCP/IP to Modbus RTU conversion. * GPIB port works with any IEEE-488.2 compatible GPIB controller.* USB port uses Microsoft supplied driver to prevent operating system change problems.* The 9009 uses a simple command set that is accessible from any port.* Controllable with Windows PC programs like C, Visual Basic, LabVIEW, VEE, etc that make VISA or SICL calls. Works with Agilent, NI and Kikisui VISA libraries* Controllable from MAC/UNIX/LINUX and similar computers with RPC calls.* Ethernet interface protocol is fully VXI-11 compliant and does not require special PC drivers.* Internal webserver with sample Modbus device control pages for Watlow F4, F4T and EZ-Zone Controllers.* OEM oriented board designed for integration inside the user's system with only one cable. On board regulator works with 5 to 15 Vdc power.* Support programs Include ICS's VXI-11 and VISA keyboard control programs and a NTML page utility for uploading your customer webpages.
-
product
Modbus Plant Simulator
If you are an Industrial Control engineer or technician dealing with Modbus RTUs, PLCs, Drivers and SCADA servers, you must have Modbus TCP Plant Simulator is your toolbox. With this tool, you can test and verify your SCADA tag names, IO Server mappings, Modbus addresses, alarms, visualization displays, historians, reports, data communication channel throughput, controls, and more without deploying even one RTU or PLC.
-
product
RS232 RS485 RS422 Serial To Ethernet Modbus Converters / Device Servers
In the past two decades, legacy serial communication protocols such as Modbus have merged rapidly with modern TCP/IP communication, yielding benefits including widely available infrastructures and greater distance, reliability, and flexibility. CommFront offers a range of industry-proven, easy-to-use serial to Ethernet converters and device servers, both hardware and software types. The applications of our serial to Ethernet converters include acting as a device server or a Modbus RTU/ASCII to Modbus TCP protocol converter; extending serial ( RS232 / RS485 / RS422 / TTL) communication distance over Ethernet network; controlling serial devices from remote Modbus TCP software or Modbus RTU master via Ethernet network; making a wide variety of M2M communication applications possible by enabling client access independent of any operating system or proprietary protocol; and converting conventional serial data network into TCP/IP network, etc.
