Safety
-
product
Smart Aircraft System
The Astronics Smart Aircraft System makes that possible. Our patented system enables the immediate, cabin-wide gathering of thousands of data points using sensors & IoT (Internet of Things) technology. The result? You get the insight you need—when you need it. Insight that helps you on every flight. Insight that allows you to improve your operational efficiency, your cabin safety, and your overall passenger experience.
-
-
product
Robot Software
Our fully integrated software enhances productivity by combining control, safety, motion and more into a single software architecture and development environment.
-
product
Multifunction Instrument
COMBI521EV
COMBI521EV is the new HT instrument to perform verification and control of electric car charging stations (EVSE) safety according to IEC / EN 61851-1 and IEC / EN60364-7-722 standards. Being a combined verification instrument, COMBI521EV also carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type B, A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
product
Pressure Accelerated Aging Test Chamber (HAST)
Guangdong Test EQ Equipment co., Ltd.
- Hyper-Accelerated Aging: Combines high temperature, 100% RH, and pressure to simulate decades of environmental degradation in days.- Precision Control: Triple-redundant PT100 sensors and PID algorithms for<1% pressure fluctuation.- Safety Systems: Auto-pressure release valves, hydrogen gas detection (for battery/polymer tests), and emergency cooling.- Corrosion-Resistant Build: SUS316L stainless steel interior, PTFE-coated seals, and ceramic-coated heaters.- Smart Connectivity: IoT-enabled remote monitoring, predictive maintenance alerts, and compliance with FDA 21 CFR Part 11 data integrity.
-
product
Drivetrain Tester
G5.DT
The G5.DT series is bidirectional regenerative. It was developed specifically for testing DC components of the electrical drive train or DC components of other parts of the vehicle electrical system. It is suitable for use in laboratories and on test benches. The modular and finely graded G5.DT series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3. The power supplies are equipped with a powerful CAN multi-protocol interface (1 kHz, 16 bit) and optionally offer test bench relevant safety functions such as PL e according to EN ISO 13849, insulation monitoring as well as automatic discharge on the load side in case of shutdown.
-
product
Cable Assembly 15-Pin D-Type, Male to Unterminated With Tinned Ends, 2m
A015DM5-T-0A200
The 15-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper Wire. The connector can be secured to the associated product by screwlocks. The unterminated connections are coded to match the connector pin designation. When using this product additional cable strain relief arrangements may be necessary and appropriate electrical safety precautions should be observed.
-
product
Test Samples
Performance testing of metal detection equipment is a crucial part of a food safety and quality management system. Confirming the correct performance of your detector at regular intervals ensures your system is compliant with programs like FSMA, SQF, GFS, BRC and other relevant auditing schemes.
-
product
Tech Meter Kit
TMX-589
* Professional Grade True RMS Digital Mulitmeter * CATIII 1000V safety rating * Safe for use on Hybrids * Waterproof to IP67 Standards
-
product
Residual and Diffusible Hydrogen Determination by Hot Extraction
DH603
Hydrogen determinations are delivered quickly and precisely with the DH603 using residual, diffusible, and total hydrogen measurements. This robust instrument determines the amount of total hydrogen (or diffusible and residual hydrogen when equipped with the optional integrated sample piercer) present in ferrous alloys. A small footprint, user-friendly operating software, increased instrument safety and reliability are all part of the advanced DH603 design.
-
product
Safety
Chroma Systems Solutions, Inc.
The purpose of safety testing medical electronic equipment is to be sure that a device is safe from electrical hazards to the patient and caregivers. There are a number of UL, European and Canadian standards that serve as the ruling body on how medical products will be tested, one in particular, IEC60601 (the International Electrical Safety Standard for medical electronic equipment) is experiencing “global harmonization,” meaning it has been accepted and implemented around the world. The IEC60601 standard is mainly intended for product development where safety considerations must be taken into account early in the design phase of a product, however much of it is applied to production line testing since it is the only way for a manufacturer to be sure they are shipping safe product.
-
product
High Performance Liquid Chromatograph Triple Quadrupole Mass Spectrometer
LCMS-8045
Equipped with a heated ESI probe, the LCMS-8045 has the highest sensitivity in its class. The heated ESI probe, high-temperature heating block, desolvation line (DL) and drying gas, all act to promote desolvation and prevent contamination due to the penetration of liquid droplets into the MS unit. This improves the robustness, so reliable and high-accuracy data can be obtained over the long term. The LCMS-8045 also achieves the world's fastest scan speed (30,000 u/sec) and polarity switching speed (5 msec). These enable ultra-high-speed, high-sensitivity analysis. The excellent cost performance of this system is demonstrated in food safety, environmental analysis, and other quantitative analyses, it can be upgraded to the LCMS-8060.
-
product
PXI Single Bus 32-Ch 2A Fault Insertion Switch
40-190B-201
The Single Bus, 32 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally closed through relays, so in the default state, there is a path between input and output for all signal channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
product
Partial discharge measurement with remote wireless reading
PD-LT
The PD-LT allows online partial discharge detection on cable accessories such as cable head for safety and maintenance purposes.The PD-LT indicates the intensity of the partial discharges, converting the electrical charge units (pC) into decibels (dB). Thus the reading is kept as a simple intensity level indication, proportional to the probability of a fault's presence in the tested medium voltage accessory.The remote display gives a dB value of the probe's measurement. The dB value will vary along with the discharges indicators on the PD-LT probe. The measurement range is from 0 to 65dB and the display will show ''OL'' if the reading is over 65dB.
-
product
Non-contact Io/Ior Leakage Clamp Meter
MCL-500IRV
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Safety by non-contact sensor, not touching live part directly (prevention of electric shock, short-circuit, etc.).・Easy to carry and operate, clamp CT + display part integrated type.・Measurable line current + leakage current + resistive leakage current by one unit.・Available direct voltage input at live part as ordinary.・True RMS measurement (I, Io, V).・With filter switch to cut high frequencies.
-
product
DMS Transmitter
Knick Elektronische Messgeräte GmbH & Co. KG.
Transmitter for load cells and the evaluation of strain gages in 6 mm housing with calibrated range selection.Detection signals from sensors for physical variables such as displacement, angle, pressure or force. Functional safety up to SIL 2, SIL 3 redundant to parameterization via interface or intuitively, directly on the device. Universal use with 24 V DC or AC power supply.
-
product
Safety Testing
KTL Safety Group is fully accredited to meet the growing needs for worldwide safety testing and compliance and provides: Safety testing and certification of electrical and electronic equipment to international and European safety standards, Pre-compliance evaluations that identify problem areas early in the design stage, to reduce the need for potentially expensive modifications.
-
product
Self-reclosing Overcurrent And Residual Current Protection
Wide range of solutions to guarantee personnel safety as well as maximum service continuity in the event of a ground current or breaker trip, with automatic reconnection of the installation. Available with RS-485 communications (Modbus RTU) and remote control inputs/outputs.
-
product
Microwave Power Modules
S-BAND to KA-BAND
Communications & Power Industries
Each of CPI TMD's TWT-based units is comprised of a compact power supply and mini TWT, combined into an ultra-compact, lightweight "drop-in" amplifier block. This simplifies system design and installation, increases reliability and minimizes safety hazards. The units also feature high electrical efficiency and excellent thermal management. Performance is factory set, removing the need for any user adjustments in the field and, if necessary, permitting easy field replacement of the complete unit. The product range covers S-band to Ka-band, and includes continuous wave (CW), pulsed and CW/pulsed units of extremely compact design. At only 1.7 kg with over 110 W output power, the PTXM1000 is believed to be the market’s highest power density MPM.
-
product
NI-9237, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
780264-01
50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The NI‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the NI‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools.
-
product
Performance Exams
Sturdy sheet steel housing with safety door and electrically driven base with built-on sample mold. The compaction takes place via a rolling segment with force / path-controlled drive device from above. The sample mold and the rolling segment are equipped with software controlled heating. The measurement of force and displacement is done by electronic sensors. The entire compaction process is controlled with Windows software and PC via preselected sequence programs.
-
product
Multifunctional Testers
Electrical installation safety is nowadays more important than ever with the proliferation of increasingly complex domestic electronic appliances people install in their homes that require reliable power supply lest they become damaged and pose a fire and electrocution risk. Effects of unreliable and even dangerous electrical installations are even more acutely felt in industrial environments where they translate into production losses.
-
product
PC Based Automatic Safety Analyzer
D-9009 SF
The PC Based Automatic Safety Analyzer is ideally suited for fast paced production lines delivering high volumes of finished household appliances. This Tester has been appreciated by many household appliance manufacturers in India such as Tecumseh, Havells, Hitachi, IFB, LG, Voltas, Videocon, Yash fans to name a few.
-
product
Optoelectronics
Renesas provides a wide range of optoelectronic devices, including IC output photocouplers (optocouplers) featuring a high response from 1Mbps to 15Mbps, as well as general purpose transistor output devices featuring high isolation voltage, high temperature operation and compliance with various international safety standards. For motor drive applications, dedicated photocouplers provide high isolation voltage, high temperature operation, high output current, and high-speed switching. These are complemented by a diverse range of ultra-high speed devices for fiber-optic applications, as well as solid state relays (OCMOS FETs).
-
product
Hydrostatic Test Stand, Hydraulic System Components
9901HTX-100LR2-36x36x15
The 3 ft. wide x 3 ft. deep Hydrostatic Test Stand, Hydraulic System Components is utilized for pressure testing hose and tube assemblies as well as any component requiring hydrostatic testing in the integral safety test chamber.
-
product
DC Switching Power Supply
MPS-3206
OVP and OCP to ensure the safety, smart fan, unique air duct design keeps normal temperature for long time full load working with low noise.Pure copper terminal makes good conduction, have better performance.110V/220V Input voltage switching.4 Digits Readings LED Display and 10mV and 1mA resolution,5 groups of parameter storage, coding switch to avoid casual touch.Easy to adjust voltage and curent through the knob, and we added an output button to prevent accidental touch.24 hours continuous operation, with high stability, suitable for a variety of working environments.
-
product
USRP‑2930, 20 MHz Bandwidth, 50 MHz to 2.2 GHz, Included GPS-Disciplined OCXO, USRP Software Defined Radio Device
781910-01
20 MHz Bandwidth, 50 MHz to 2.2 GHz, Included GPS-Disciplined OCXO, USRP Software Defined Radio Device - The USRP‑2930 is a tunable RF transceiver with a high-speed analog‑to‑digital converter and digital‑to‑analog converter for streaming baseband I and Q signals to a host PC over 1 Gigabit Ethernet. It also features a GPS-disciplined oscillator (GPSDO) with PPS accuracy of ±50 ns. You also can use the NI USRP‑2930 for the following communications applications: white space; broadcast FM; public safety; land-mobile, low-power unlicensed devices on industrial, scientific, and medical (ISM) bands; sensor networks; cell phone; amateur radio; or GPS.
-
product
Infrared Thermometers
Instant, less-than-a-second temperature readings of any surface, °F/°C switchableIdeal for food preparation, pharmaceuticals, field use, electronics, and safety inspectionFeatures minimum/maximum memory, average readings, and high/low audible alarms (Cat. No 4484)
-
product
Surge Generator
CFL SG 1610
SCOPE offers CFL SG 1610, Surge Generator with output of 16kV and 1000 Joules. It is ideal choice for fault location on all types of power cables from LV to EHV. CFL SG Series is equipped with different Protections, Interlocks and Auto-discharge Facility to ensure User Safety during operation. User Friendly controls, adequate form factor, contact free HV terminations makes this CFL SG Series most durable and best-designed sets in the segment
-
product
Telegraph / Wooden Pole Tester
CXI-PT5000
The CXI-PT5000 is an innovative wooden pole tester that uses measurement and analysis technologies to indicate pole strength, allowing users to make an accurate assessment of the pole's stability and safety.
