Safety
-
Product
Safety Testing
-
Mobile Power Solutions specializes in guiding your company through today’s increasing quagmire of battery-related safety regulations. MPS provides comprehensive regulatory compliance, safety, and performance testing; we are ANAB accredited to ISO/IEC 17025:2017.
-
Product
Electric Safety Tester
PVCHECKs
-
The multifunction device PVCHECKs allows quickly and safely carrying out the electric safety tests provided for a PV system (section in DC) and the functional test of modules/strings the system consists of according to the requirements of Standard IEC/EN62446.
-
Product
Multifunctional Safety Tests
-
Manufacturers of electrical or electronic products are required by law to carry out an electrical safety test before placing them on the market. This final test takes place at the end of the manufacturing process and is therefore also referred to as an EOL test (end-of-line). Depending on the prescribed standard and directive, the following parameters are tested:- Leakage current and discharge current- Insulation resistance or the insulation strenth- Dielectric strength or electric strength- Correct installation of the protective conductor (ground continuity and ground bond test)- Faultless functioning of the product under the conditions defined for intended use (function or run test
-
Product
Pointer Safety Tester
-
Is specially designed for production lines and quality control. Inspection instruments, insulation and withstand voltage test conditions, research and development, quality control, experiments, and production are essential for safety inspection of various electrical products. It can be used for stand-alone, timing, remote control, judgment, and automatic testing, and can apply for any national safety standard instrument.
-
Product
Safety Products
-
This ACE product group provides Emergency braking to safely slow down moving loads and reduce damaging forces. Although the safety shock absorbers, TUBUS elastomer bumpers and clamping elements differ so much in design, every single ACE component provides the best protection for your machine.
-
Product
Safety Ohm Meter
Type 1681
-
Aeronautical & General Instruments Ltd.
The Type 1681 Safety Ohm Meter range are rugged highly portable intrinsically safe instruments for use in potentially Explosive Atmospheres. Six measurement ranges enable it to measure resistances from 1mΩ and 20kΩ using a 3½ digit backlit LCD display.
-
Product
Public Safety
-
Schnoor Industrieelektronik GmbH & Co. KG
Reliability, performance as well as quick, simple operation is of special importance in the range of public safety, police, fire brigades and rescue services. Schnoor Industrieelektronik develops radio systems, application and migration concepts, corresponding to the safety standard for Security Authorities and Organisations.
-
Product
Safety Relay
-
Leuze electronic GmbH + Co. KG
With the MSI safety relays, individual safety sensors can be integrated quickly and easily into the safety circuit of machines and systems. The MSI contact extensions are used both as an output extension for OSSDs and for contact multiplication for evaluation units and safety controls.
-
Product
RF Safety Monitoring
MVG EME Guard XS 40GHz
-
EME Guard XS 40 GHz has been specifically designed to cover the new 5G millimeter wave bands. This RF safety tool is important for keeping those working close to RF emitters safer. It is easy to use, continuously scanning electromagnetic waves, and alerts the user when acceptable pre-selected limits have been exceeded.
-
Product
Electrical Safety Tester
-
Basic testing methods of Glow wire device> and UL 746A, IEC829, DIN695, VDE0471, the Glow wire tester ZRS-3H/ZRS-3HS is suitable for resistance to abnormal heat and fire test on lighting lamps, electronic products and household appliances. Adopting high-temperature coating spraying on steel structure and imported instrument display, with easy operation, stable performance the equipment is applicable to flame resistance tests of all levels of QC departments and corresponding enterprises.
-
Product
Safety Proximity Sensors
-
Leuze electronic GmbH + Co. KG
With their encapsulated and contactless design, safety proximity sensors are insensitive to contamination and humidity. They operate free from wear and also have a long life expectancy, even with frequent operating cycles. They are also used wherever it is difficult to precisely guide the moveable protective device. All devices feature a high-strength plastic housing. Furthermore, the devices with RFID transponder provide maximum protection against tampering.
-
Product
Safety Relay Modules & Sensors
-
Using safety relay modules, you can reliably implement safety functions in machines and systems. They monitor signals from emergency stop buttons, light grids, and safety door switches, and initiate a safe state where necessary.
-
Product
Electric Safety Tester
PV-215
-
The multifunction device PV-215 allows quickly and safely carrying out the electric safety tests provided for a PV system (section in DC) and the functional test of modules/strings the system consists of according to the requirements of Standard IEC/EN62446.
-
Product
Product Safety Testing & Certification
-
MET has been certifying, listing, and labeling products for electrical product safety for more than 40 years. In that time, MET has certified thousands of products for compliance to electrical safety standards. This translates into literally millions of products sold in the U.S. and Canada labeled with the MET Mark.
-
Product
Safety Products
-
Contrinex sensor spacers, mounting brackets, column accessories, light curtain extenders, and more.
-
Product
Safety Radar System
-
Leuze electronic GmbH + Co. KG
The world's first safe 3D radar system, LBK from Inxpect S.p.A., was developed for the monitoring of hazardous areas in harsh industrial environments. It detects the bodies of persons and in doing so monitors the protected area for access and presence. Using the controllers, up to 6 sensors can be combined in one application.
-
Product
Electronic Safety Sensors
-
Non-contact, RFID-based devices designed to monitor movable guards like doors, panels, and hoods in industrial machinery.
-
Product
Product Safety Testing
-
Low Voltage and Machinery Directives Product safety is everyone's concern and covers a wide area. It is therefore no surprise that a great number of European Directives are aimed at safety. Kiwa Dare performs tests and measurements in the area of Low Voltage and Machinery Safety for many years now.
-
Product
Electrical Safety Wall
-
AllWin Instrument Science and Technology Co., Ltd.
1. Electricity Safety Wall2. 50/60HZ3. Four detection ways4. Continuous testing
-
Product
Safety Network (AS-i Safety at Work)
-
*Monitoring of up to 31 safe AS-i slaves*Applications: door monitoring, light curtains, e-stop, two-hand control*Safe AS-i modules for field applications and control cabinets*Safe AS-i door switches with guard locking and guard lock monitoring
-
Product
Charge System Safety
-
Renesas' charging system safety circuits are optimized to provide a redundant safety protection to an Li-ion battery charging system by monitoring input voltage, battery voltage and charge current.
-
Product
RF Safety Monitoring
MVG EME Guard Plus
-
The EME Guard Plus is designed to record EMF exposure near antennas while continuously monitoring potential over-exposure. Lighter than the previous model, the EME Gaurd Plus makes it easier for workers to wear on the job. The longer battery life and extended memory capacity enable more measurements to be recorded.
-
Product
Safety Testing
-
Underwriters Laboratories Inc.
As the global safety science leader, our safety offerings and expertise are unparalleled. We can help you engineer safety into your products throughout your development process, reducing costs and challenges associated with innovative offerings. Our testing and certification services focus on helping our customers create a safer, more secure and sustainable world. Our mission of "working for a safer world" drives everything we do. Leverage our offerings and insights to build trust and confidence in your products and services.
-
Product
Safety Command Devices
-
Leuze electronic GmbH + Co. KG
For stopping in emergencies, EN ISO 12100‑1 stipulates protective devices and supplementary measures such as E‑Stop buttons or emergency rope switches. The E‑Stop buttons are used wherever it makes sense to be able to enter a stop command at a specific location. E-Stop rope switches are used for larger danger zones.
-
Product
Product Safety Testing
-
NCEE Labs is an A2LA Accredited product safety compliance testing lab. We specialize in compliance testing to US and harmonized international standards. NCEE Labs also offers NRTL testing services. With experienced product safety engineers, we provide expert assistance, whether evaluating early prototypes or assisting with aftermarket design changes.
-
Product
The Complete Appliance Safety Tester
Primetest 100
-
Primetest100 a combination tester that gives you the functionality of a PAT tester, an IEC lead and extension lead tester and a power socket checker in one compact easy to use instrument.
-
Product
Safety Tools Testing
-
Weshine Electric Manufacturing Co., Ltd
1. The high voltage is extremely spherical and the grounding voltage is annular.2. The grounding electrode is fixed and the high voltage electrode can be electrically driven to move to the left and right.
-
Product
Safety Chamber, Hydrostatic Test
9901HTX-72x24x12
-
The 6 ft wide by 2 ft deep Hydrostatic Test Safety Chamber, when combined with one of our pump systems, provides a complete hydrostatic test system for testing hose and assemblies or other components requiring pressure testing.
-
Product
Safety Analyzer
SA-2000
-
The BC Biomedical SA2000 Features: AAMI Load Earth / Ground Lead Resistance Earth/Ground Leakage Current Chassis Leakage True RMS Measurements 85 to 265 VAC Operation.
-
Product
Law Enforcement/Public Safety
-
Vehicular and Handheld antennas are available for communication, surveillance, signal DF, network repeaters and RF Jamming applications. A single omni or high gain directional ARA antenna may cover all cellular and/or Tetra communication bands and are compatible with all network technologies (GSM, CDMA, etc.). These wideband antennas replace the need for several single band antennas and are ideal for vehicular installations as well as handheld radio mounted applications. Permanent installations, quick deploy magnetic mounts or convenient pistol grips for radio location are available.
