Regulators
-
product
CO2 Concentration Transmitter
H5024
The regulators are designed for online measurement of temperature (C or F), relative humidity and carbon dioxide concentration of air without aggressive ingredients. Measured temperature and relative humidity are recomputed to following humidity expression: dew point temperature, absolute humidity, specific humidity, mixing ratio and specific enthalpy.
-
product
Brushless Permanent Magnet Alternators
NoBrush 400 Hz alternators provide excellent voltage stability, eliminating the need for further regulation in most applications. These Brushless Permanent Magnet Alternator Generators respond quickly to significant load changes, and produce an output waveform free from sharp peaks and spikes. EMI generation is very low; in most instances, it may be considered zero.
-
product
AC Power Source, Frequency Converter
BL1350 Series
Behlman's BL1350 AC Power Supply / Frequency Converter / Inverter, requires just 3.5" of rack height, and weighs as low as 45 pounds, yet it delivers 1350 VA of quality AC power. In the BL 1350, you'll find the quality features you expect from Behlman, fully adjustable frequency and voltage, total harmonic distortion of less than 0.5%, high efficiency, plus excellent line and load regulation.
-
product
Bench Power Supply, Adjustable, Fixed, 3 Output, 0 V, 32 V, 0 A, 3 A
72-13600
*Triple channel linear DC power supply*Dual channel adjustable & one channel fixed*Constant current & constant voltage operation*Forced ventilation & temperature cooling system*LED digital tube display shows voltage and current simultaneously*Low ripple & low noise, output on/off control*Overload and reverse polarity protection*115VAC/230VAC (50Hz/60Hz) AC input voltage and 0.01% high regulation*12-month limited warranty *view Terms & Conditions for details
-
product
Process Gas Condenser/Chiller
Process gas chillers are designed to condense vapors out of a process gas stream so it may be collected and properly disposed.This chiller condenses Styrene (a gas that is regulated by the E.P.A.) out of a process gas stream. The chiller operated continuously at a -25C (-13F) outlet air temperature as long as the process gas stream was flowing.
-
product
Power Supply PowerLab 305d-ii
PowerLab triple Series power supplies are reliable and accurate laboratory equipment with two outputs with adjustable and stabilized DC voltage and regulated (limited) power consumption and additional output has-voltage. Adjustable outputs can work independently, in series (max output voltage 120V DC for model 605-II) or parallel (max current of 10A for models 305-II and 605-II). Power can be used in the design of electronic products, scientific works, laboratories, production lines and in teaching.
-
product
FCC Certification
Here we provide access to information about the FCC authorization methods, excerpts of FCC rules that cover marketing of devices in the United States as well as general terms and definitions used in within the FCC authorization scheme. To file an application for certification at any time, please click the “Service Quote” link above or contact us today.Telecommunication Certification Bodies (TCBs) have been appointed by the Federal Communications Commission (FCC) to approve equipment as required under Title 47, Part 2 of the Code of Federal Regulation (CFR).In essence, this gives you, the manufacturer or responsible party, additional options for product approvals by allowing you to choose from one of many TCBs.Information presented here is derived from FCC CFR Title 47. Please see the FCC CFR web page for access to the official rules or vist Title 47 at e-CFR.
-
product
Temperature and Humidity Regulator
H3020
Built-in relative humidity, temperature sensors. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
product
Installation Testers
In order to test all necessary components of any installation and to perform all tests within the regulations, Nieaf-Smitt is offering several installation testers. There are individual testers for parts of the regulation and four combination testers.
-
product
6000 Series (Power Meter)
Digital Power Meter is designed to measure the power line parameters of AC / DC and DC / DC power supply. It is suitable for AC / DC Adapter, Charger, Quick Charger, LED Driver and DC / DC Converter. It is also suitable for uninterruptible power supply UPS, Regulators AVR, Inverter, batteries, AC / DC power supply / components ... and other applications.
-
product
Electrical Calibration
GF6018A
Beijing GFUVE Electronics Co.,Ltd.
The equipment is compliance with national verification regulation: JJG1242005 "Ammeter, voltmeter, power meter and resistance meter verification rules" and related national standards. 0.05 single-phase AC/DC standard source, can verify magnitude 0.2 and the following AC/DC voltmeter, ammeter, frequency meter, resistance meter. The source signals by using DSP and 16-bit high-speed analog-to-digital converters of controllable sine wave, the distorted wave signal source.The equipment comes with RS-232 interface, can be connected with PC to a semi-automatic verification system. It has precise interface and multi-functions including verification, storage and query.The equipment adopts color LCD screen, chart character display is clear, with high precision, stable and reliable, convenient operation and flexible characteristics.
-
product
Transformer Analyzer
505
The UTEC 505 Transformer Analyzer is designed for testing current transformers (CT) and potential transformers (PT) without interruption of the customer’s service. This instrument measures CT admittance, CT ratio, CT primary-to-secondary phase angle and the voltage, current and phase angle of the service. With the ‘Burden CT/PT Option’, it determines the CT secondary burden capability, the regulation of the PT and its secondary burden capability and provides for CT core demagnetization.
-
product
Scienlab Measurement And Control Module
SL1068B
The Measurement & Control Module SL1068B is a rack-mount measurement module which provides voltage outputs for analog signaling – useful e.g. for the emulation of temperature sensors or the controlling of regulation vents with voltage input with 8 channels. The module can be used either as a stand-alone device or as extension for a Scienlab Battery Test System.
-
product
Arduino CAN Shield
IFB-10003-ANP
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
-
product
Mass Spectrometry
Mass spectrometry isn’t just for academics and R&D labs anymore. Analytical testing labs across, food, cannabis, environmental and industrial testing face stricter, evolving regulations that demand lower detection limits and have high throughput requirements. We have the technologies, capabilities and services to address these challenges – with ease and reliability.
-
product
Distiller
Shanghai Selon Scientific Instrument Co. Ltd.
Using double directions regulate pressure valve. Make sure that steam cooling water and filling water being divided. Water standard meet 2000 edition state pharmacopoeia Standard. Water supply cut protecting equipment(apply to controlled type). With branching control install; solenoid valve control the flow of filling water(apply to controlled type).
-
product
SparkFun Breadboard Power Supply 5V/3.3V
Here is a very simple breadboard power supply kit that takes power from a DC wall wart and outputs a selectable 5V or 3.3V regulated voltage. The .1" headers are mounted on the bottom of the PCB for simple insertion into a breadboard. Pins labeled VCC and GND plug directly into the power lines. The lone pair of pins have no electrical connection but help support the PCB.
-
product
Bench Power Supply, Calibrated w/Data, Adjustable, 1 Output, 0 V, 30 V, 0 A, 5 A
72-2690 CAL D
The 72-2690 CAL D from Tenma is a single channel adjustable bench top power supply. It is a digitally controlled industrial grade power supply with load for a long time. This compact design power supply has complete digital control, intelligent temperature controlled fan, low noise and low ripple. It also features knob lock function to avoid improper operation. This power supply has load regulation ≤0.01% +2mV (voltage), ≤0.1% +5mA (current) and line regulation of ≤0.01% +3mV (voltage), ≤0.1% +3mA (current). The setting accuracy (25°C ±5°C) is ≤0.5% +20mV (voltage), ≤0.5% +10mA (current).
-
product
Arduino CAN Shield
IFB-10003-AWP
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
-
product
Conductivity Probe
ACS60-35
Knowing the conductivity of liquid samples is a key parameter to control product quality throughout the production process. The optek ACF60 conductivity probe fulfils technical requirements of international regulations for reliable measurements ensuring quality and consistency.
-
product
High Frequency Clock Divider Board
Alliance Support Partners, Inc.
Clock Divider is designed to divide high frequency signals, up to 2.5GHz, from 4 to 256 times. It will accept single ended (Unbalanced) or differential (Balanced) signals with amplitudes as little as 100mV rms. The clock division is controlled by 4 shunt jumpers. The circuit can be disabled and the divide by counter reset with 2 control signals. The on board regulator will accept voltages from 4.85 to 15.0V. The output is capable of driving 700mV Peak to Peak into 50 Ohms.
-
product
Media Meter Software Tool
Dolby Media Meter is an innovative software tool that accurately measures loudness the way your viewers experience it in programming for broadcast, packaged media, cinema trailers, video on demand (VOD), and games. Differences in audio levels between programs and channels, or between programs and commercials, are a major annoyance to TV viewers. Although easy to hear, these differences are much more difficult to measure. And without accurate measurement, you can't regulate these irritating shifts in sound level.
-
product
Stealth Gravity Metal Detector
Stealth Gravity metal detectors are custom manufactured to suit any gravity application. The Stealth uses digital signal processing technology and has high sensitivity levels to ensure the detection of the smallest ferrous, non-ferrous and stainless steel contaminants. The built-in data collection software with USB data transfer establishes the Stealth as an effective critical control point complying with stringent HACCP regulations.
-
product
RH, Temperature and CO2 Transmitters
HD46… Series
The instruments of the HD46… series are transmitters, indicators and regulators suitable for measuring and monitoring the following environmental parameters, depending on the model:
-
product
Digital Thermometer
TH300
The Milwaukee TH300 compact digital thermometer is specifically designed to help professionals and home owners regulate their pools, wine process, classroom experminents or labs duties. Keeping the proper temperature improves results of beer and wine output. It also helps in understanding the quality of lab data. Keep temperature in your target range for better results.
-
product
EMI/EMC Testing
EMI/EMC testing can reliably predict product performance in any electromagnetic environment. Testing can also determine the possibility of interference with other equipment, possibly degrading performance. Testing may be required in order to comply with regulations or for informational and product improvement purposes.
-
product
Isolators
Rishabh Instruments Pvt. Ltd.,
To electrically isolate input, outputs and power supply. The isolator fulills all requirements and regulation concerning electromagnetic compatibility EMC and safety.
-
product
"Stiff Grid" and Parallel Operation AC Generator Excitation Regulator
SVRFP
The Kinetics model SVRFP Exciter/Regulator rectifier is designed and rated in capacity and operating parameters for the application of exciting the fields on an AC generator in parallel with other AC generators and the power system is a "stiff system" in relation to loading. A "stiff system" is a generating system that is of sufficient capacity or the generator is "small" in relation to the system grid, that the AC system voltage under impulse/step loading condition does not require forcing of the generator field to maintain the power grid voltage. Systems are designed with a standard unit service factor to operate within the +10% to -20% nominal voltage rating at 100% current rating.
-
product
Software
Eagle’s extensive portfolio of product inspection systems can be enhanced with several unique software options designed to ensure maximum uptime and compliance with Hazard Analysis and Critical Control Points (HACCP) principles and global safety regulations.





























