Modules
See Also: Contacts, Boards, ITA, Cable Assembly, Cards
-
Product
PXI Solid State Switch Module, 6xSPST, 30 A, Hardware Interlock
40-183B-011-HI
Switch Module
The 40-183B-011-HI has 6 high current SPST switches with hardware interlock in two PXI chassis slots. Each SPST switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation.
-
Product
Spectrum and Signal Analyzer Frequency Extension Systems
SAE
-
The SAE modules are designed to interface with your existing microwave signal or spectrum analyzer and extend its frequency coverage to 500 GHz.
-
Product
Switch Fabric Modules
-
Switched fabrics provide the interprocess communication backbone for OpenVPX systems - and these modules enable you to achieve the maximum benefit.
-
Product
PXI 48 x SPDT Power Relay Module
45-157-001
Relay
The 45-157 SPDT Power Relay Module consists of 48 single pole changeover relays controlled by a PXI/CompactPCI interface. It is suitable for applications were conventional reed-relay based switching modules do not have sufficient voltage rating or current carrying capacity. All 48 contacts are electrically isolated from each other and are capable of switching resistive and inductive loads up to 2000VA at 240V AC.
-
Product
NI-9478, 50 V, 16-Channel (Sinking Output), 50 µs C Series Digital Module
779940-01
Digital Module
50 V, 16-Channel (Sinking Output), 50 µs C Series Digital Module - The NI‑9478 works with industrial logic levels and signals to connect directly to a wide array of industrial relays, solenoids, and motors. The NI‑9478 features programmable current limits, which provide customizable system protection that is ideal for solenoid and valve control applications. Each channel is compatible with signals from 5 V to 50 V and features isolation from channel‑to‑earth ground.
-
Product
PCI Bus Carrier for IP Modules
APC8620A
-
This board interfaces industry-standard Industrial I/O Pack (IP) modules to a PCI bus on a PC-based computer system.
-
Product
PXI High Density Precision Resistor Module, 3-Channel, 3.5Ω to 1.51MΩ
40-298-144
Programmable Resistor Modules
The 40-298-144 is a high density programmable resistor module with 3 channels which can be set between 3.5Ω and 1.51MΩ with 2Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI Single Transfer Switch 18GHz 50Ω SMA
40-782-521
Switch Module
The 40-780 Microwave switching module consists of one, two, three or four changeover switches capable of switching frequencies to 18GHz (optionally to 67GHz) in 50Ω or 2.5GHz in 75Ω. The 40-782 module consists of one or two microwave transfer switches. It has a characteristic impedance of 50Ω and is available in versions with maximum operating frequencies of 18GHz, 26.5GHz or 40GHz.
-
Product
Single Loop Controller
1160+
-
The 1160+ controller is an evolved product from the West N6100. The product benefits from having more versatile features and user-friendly functionalities such as remote setpoint inputs, digital inputs, plug-in output modules, a customisable operator/HMI menu, jumperless and auto-hardware configuration, and 24VDC transmitter power supply.
-
Product
PXI Resistor Module Dual 12-Channel (no resistors fitted)
40-281-021
Programmable Resistor Modules
The 40-282 is a potential divider with up 24 separate channels. This can be used to emulate potentiometer devices, each channel having a fixed R1 R2 ratio. Additionally, the centre point can be shorted to either of the potentiometer end points.
-
Product
EMX-7XXX
Programmable Resistor Modules
The AMETEK VTI Instruments EMX-7000 Series PXIe Precision Programmable Resistor Ladder modules provide four independent channels of programmable resistors. The EMX-7004 is capable of delivering exceptional stability and accuracy for any resistance value between 1 Ω to 16,383 Ω and can be adjusted in 1 Ω increments through the software application programming interface (API) or dynamic soft front panel.The EMX-7005, EMX-7006 and EMX-7007 are perfect for applications requiring higher resistance values, with programmable settings ranging from 163 kΩ to 16.383 Mohms, while the EMX-7014, 7015 and 7016 are ideal for general purpose applications not requiring ultra high accuracies.
-
Product
6U VPX GPGPU Processing Cards
-
Curtiss-Wright Defense Solutions
For systems requiring compute-intensive capability or using deep learning frameworks for AI applications, these highly engineered modules provide a field-proven hardware foundation. These processing powerhouses leverage the latest GPGPU advancements from NVIDIA for machine learning and artificial intelligence applications.
-
Product
Adjustable Length Linear Backlight, 300 mm to 2100mm
Vitech A1905
-
Modules A1905 are designed for pulsed or continuous illumination of objects in machine vision systems. The time of ignition (90%) and blanking (10%) of the module is less than 1 μs with jitter of the front (jitter) no more than 2 μs, which allows the modules to be used for exposure with "slow" cameras.
-
Product
Signal Generators, Arb.
-
Function and arbitrary signal generators in the LF and lower HF range up to 500 MHz, generation of standard signals (sine, square, triangle...), fixed and user-definable arbitrary signals; Modulations, Burst, Sweep
-
Product
SNR Noise Generator
CNG-EbNo
-
The CNG-EbNo is a fully automated precision signal to noise (AWGN) generator that sets, and maintains a highly accurate ratio between a user supplied carrier and internally generated noise, over a wide range of signal power levels and frequencies. The internal AWGN meter provides repeatable SNR waveforms for accurate signal generation. The instrument gives system, design, and test engineers in the telecommunications industry a single tool to generate precision signal to noise ratios. These signals are used to compare theoretical BER to SNR ratios, found in "waterfall" type graphs, with measured values from the DUT to evaluate different modulation schemes. Users can obtain higher yield through automated testing, plus increased confidence from repeatable, accurate test results. Standard units can be modified for specific customer requirements. Please consult the factory for pricing and availability of these requests.
-
Product
PXI 4 Slot BRIC Solid State 160x8 1-Pole (5 sub-cards)
40-563A-021-160X8
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance PXI matrix requirements and are constructed using solid-state switches. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
i1 XL (High Power)
-
Ideal for high amperage applications. Single module offers 4 high power contacts in one connector. Removable backshell allows easy access to wiring for maintenance and probing.
-
Product
Standard Voltage 50-Pin D-Type Connector & Cable Accessories
-
The Standard Voltage 50-Pin D-Type connector is used on PXI switching products to provide a medium density connector solution. Connection solutions for modules with High Voltage Rating D-Type connectors are also available.
-
Product
PXI 16 Trib Daisy Chain Switch Balanced 96 W
40-796-001
Relay
The 40-795/796 Daisy Chain Switching Module is designed for telecom test applications. It allows production or verification testing of SONET/SDH transmission multiplexers switching 2MBit/s or 1.5MBit/s data over 100 or 120 balanced lines.
-
Product
QorIQ P40x0 Processor AMC, SRIO
AMC719
-
The AMC719 is a Processor AMC (PrAMC) in a single module, mid size AdvancedMC™ (AMC) form factor based on the Freescale P4040 and P4080. The module follows the AMC.4 and AMC.2 specifications and the SRIO runs as dual x4. The module has options for up to 16GBytes of DDR3 memory with ECC.
-
Product
PXI Multiplexer, Very High Power DC, 4-Channel, 40A, 14V
40-664A-001
Multiplexer Module
The multiplexer is suitable for switching heavy loads or for slave switching large external relays, contactors and solenoids. In particular these relay modules are designed for automotive test applications requiring the switching of DC voltage at high current.
-
Product
1-Chan 3.6 GHz or 2-Chan 1.8 GHz 12-bit A/D with Virtex-6 FPGA - 3U VPX
Model 52640
-
- Ideal radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- One-channel mode with 3.6 GHz, 12-bit A/D- Two-channel mode with 1.8 GHz, 12-bit A/Ds- 2 GB of DDR3 SDRAM- Sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- 3U VPX form factor provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
PXI 2A 39xSPST High Density Power Relay Module
40-137-201
Relay
These Power Relay Modules are suitable for applications requiring power relay switching with high density. The feature 2A current and voltage to 110VDC/250VAC, they are configured as Single Pole Single Throw (SPST). Connections are made via front panel mounted 37 or 78-pin D-Type connector.Along with this 39 x SPST version, the range also includes a 32 x SPST, 2A version and a 16 x SPST, 5A version - go to Also in the Range above to learn more.Typical applications will be found in Automotive Test, Aerospace Test and Power Cell Test applications.
-
Product
sbRIO-9225, Non-Enclosed, 300 Vrms, 50 kS/s/ch, 24-Bit, Simultaneous Input, 3-Channel C Series Voltage Input Module
780588-01
Voltage Input Module
Non-Enclosed, 300 Vrms, 50 kS/s/ch, 24-Bit, Simultaneous Input, 3-Channel C Series Voltage Input Module - The sbRIO‑9225 performs differential analog input. The wide measurement range is well suited for high-voltage measurement applications such as power metering, power quality monitoring, motor test, battery stack testing, and fuel cell tests. You can perform transient and harmonic analysis with high-speed simultaneous sampling. In addition, you can prevent ground loops and add safety to a system with 600 Vrms channel‑to‑channel isolation between the three sbRIO‑9225 channels. Non-enclosed modules are designed for OEM applications.
-
Product
Multifunction Process Calibrators
-
AMETEK Sensors, Test & Calibration
Our multifunction process calibrators read and source RTD, thermocouple, current, voltage, frequency, and resistance to calibrate or verify your process sensors. They can also be combined with APM CPF pressure modules to calibrate pressure, or a dry-block to calibrate temperature. The ASC-400 features a large full color display with an advanced simplicity, easy-to-use interface.
-
Product
LXI Dual 24 X 8 Video Matrix, SMB (50R)
60-711-721
Matrix Switch Module
The 60-711 is a Dual 24x8 Video Matrix Module suitable for switching frequencies up to 25MHz. It has a characteristic impedance of 75 Ohm with the option of SMB or MCX connectors or, with a larger case size, BNC connectors. It is designed to provide a simple and scalable bidirectional matrix for video frequencies and is intended for the easy construction of high performance bidirectional matrix switching systems. Software configuration allows the 60-711 to be set as a dual 24 by 8 matrix, a single 48 by 8 matrix and other configurations.
-
Product
PXI Very High Density Versatile 2 Amp Multiplexer
40-612A-002
Multiplexer Module
The 40-612A Very High Density Versatile Multiplexer module features a wide range of software selectable switching configurations. It is especially useful where a number of high density multiplexers are required with the option of easily altering the channel count as a test system evolves. Typical applications include signal routing in ATE and data acquisition systems. The 40-612 module uses high quality electro-mechanical relays, connections are made via a front panel 160 pin DIN41612 connector. The module can be software configured into one of a large number of different multiplexer modes. Relays allow the multiplexer banks to be set in 1 or 2 pole mode and inter-bank switching enables the channel count to be increased up to a maximum of 128
-
Product
64 Points High Density Terminal Module
HSL-TB64
-
*Field I/O wiring connection for HSL I/O modules*Spring terminal for easy field wiring*Power and ground included for each signal channel*Interlocking design for rugged installation*Power LED indicator*DIN rail mounting
-
Product
PXI Interface Module, AIT ARINC 429
M3407A
Interface
Interface to the LRU in avionics test solution 4, 8, 16, or 32 software programmable Tx/Rx channels with full error injection/detection Programmable high/low speed operation Real-time recording and post analysis of multiple channels Concurrent operation of all Tx/Rx channels PXI triggers, star trigger, and PXI 10 MHz clock
-
Product
PXI Dual SPDT RF Switch 6GHz 50 SMA Terminated
40-880-001
Switch Module
A range of 50Ω SPDT RF switching with automatic termination of unused signals. Available as a dual switch in a 1 slot PXI module, a quad switch in a two slot PXI module or hex and octal switches in three slot PXI modules.
