Locators
are used to find or position.
-
-
Product
Wiring Analyzers for Cables, Wire Harnesses, Backplanes
CableEye M2Z, M3Z, M4
-
With our cable testers and harness testers, find defective or miswired cables instantly before they damage equipment or waste valuable technician time. CableEye® all-in-one test and cable management systems have a unique, patented graphic wiring display to visually pinpoint problems when wiring errors are detected, and offer under a second pass/fail testing for production environments. Quickly locate intermittent connections and identify their position in the cable.
-
Product
ULTRA-SONIC RECEIVER W/PARABOLIC REFLECTOR
MFJ-5008
-
Many times the noise is coming just outside your doorway, from the power lines. Power companies are usually very willing to help out with noise issues, but not all companies in this age of financial limitations will have the necessary equipment or trained personnel to properly locate nearby noise sources.
-
Product
Tone Generator
140BMC/6P
-
The following tests can be performed using the 140BMC/6P Tone Generator:*1000 Hertz or 500/1000 hertz alternating tone for tracing pairs.*Locates broken pairs/cables in walls. *Tone generator emits R.F. signal detectable by Aines Model 250SSP STATIONMAN Probe or 350 Filter Probe.*Provides talk power on dead pair.*Checks for shorts or opens, using a long-life lite-emitting diode (LED).*Continuity test.*Tip & Ring identifications.*Line condition identification. a. Clear line. b. Busy line. c. Ringing line.*Positive line verification.*Long battery life.*Nylon braided tinsel test lead wire for greater wear and flexibility.*Heavy duty nickel silver Aines 6P type alligator clips with custom designed vinyl boots.*Rubber grommet to prevent chafing on the test leads.
-
Product
Fault Locator
BIDOYNG
-
BIDOYNG fits into existing LV fuse positions using two LV fuses in parallel, creating a robust single-shot auto-recloser. The primary fuse carries the load current until a fault causes it to operate. Then, after a user programmed delay, the secondary fuse is switched in and the network re-energised without customer interruption.
-
Product
Test Program Quality Verification
CodeReport
-
CodeReport is an easy-to-use application for verifying test program quality. CodeReport comes with many different, known quality screening rules that can be used to verify your test program is complete and ready for production. CodeReport also provides a graphical Rule Editor that allows you to create your own, custom rules. Ensure your coding standards and quality specifications are correct by generating your set of rules, checks, and screenings. Easily generate a detailed report for locating, correcting, and documenting the state of your test program. Quickly identify the tester hardware and instrumentation needed to run your program with the Tester Resource report. Save a session file to quickly return to your project after edits have been made or use the Session on other similar projects to transfer your configuration and custom rules.
-
Product
High-performance LPDA
ALP690
-
The ALP690 is a high-performance LPDA (log periodic dipole array) antenna with a bypassable, built-in RF amplifier for use with wireless microphone receivers in location or studio production. The design delivers +4 dBd of passive gain in a directional pattern to extend operating range, and, when DC power is applied, the amplifier applies gain to overcome loss in long coaxial cable runs. By offering both active and passive operation modes, the ALP690 can be used as a receiver antenna (active or passive) and as a transmitter antenna (passive only).
-
Product
PXIe-5110, 100 MHz, 1 GS/s, 8-Bit PXI Oscilloscope
785768-01
Oscilloscope
PXIe, 100 MHz, 1 GS/s, 8-Bit PXI Oscilloscope—The PXIe-5110 oscilloscope has two channels that sample up to 1 GS/s with flexible and programmable settings for coupling, input impedance, voltage range, and filtering. PXI Oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that facilitates high-speed data throughput and includes analysis functions. This device is ideal for automated and partially automated applications that require flexible measurement configurations and up to 100 MHz of analog bandwidth. The PXIe-5110 also features advanced PXI synchronization and data throughput capabilities. Some options also support CableSense™ technology, which can detect and locate signal path faults, changes, or discontinuities.
-
Product
Leak Locator
XL-2
-
Lightweight & Strong11 Position filter to pinpoint leak and remove background sounds2 Sensitivity controlsSuper Sensitive magnetic transducerHigh gain, 4-stage amplifierVisual and Audible indicationsCoarse and Fine SensitivityExtremely sensitive pickup with removable 7" (177.8mm) probeBattery operated and with battery condition indicator
-
Product
Seed & Node Localization System
GammaPro
-
The GammaPro System. Simply the most sensitive and precise method for detecting radioactive seeds or locating sentinel nodes.
-
Product
Cable Test Van
BAUR Transcable 4000/S 32-3
-
Transcable 4000/S 32-3. Thetranscable 4000/S 32-3 cable test van is a 32 kV cable fault location system in 3-phase version. The system is controlled with the MGS semi-automatic control unit. The high voltage switch unit is maintenance-free and fully safe to touch.
-
Product
Software
Hole Shot
-
The modern world is changing faster than ever before and most companies and governments are migrating away from older Windows based networking technologies to web-based networks that are endlessly interconnected making information easier to share and easier to access from any device at any time. Mustang adopted web-based technology in 2016 when it embarked on a new project to advance dynamometer technology and simplify its offerings. Mustang’s goal was to increase commonality and provide customers with a more powerful and easier to manage controls package. Mustang already offered a full menu of testing capabilities, so we turned our attention to increasing access and decreasing clutter. By adopting web-based systems, Mustang can better service thousands of customers world-wide from one location and keep all of our customers on the most up to date system available. All enhancements can be pushed to all of our customers at the same time making sure all installations are up to date. Our latest controls package, Hole Shot™ Software is designed to keep our customers constantly ahead of the curve and ensure that their valuable data is secure and backed up to a secured cloud database.
-
Product
Earthquake Early Warning
MyShake
-
UC Berkeley Seismological Laboratory
MyShake is a free app for Android phones that has the ability to recognize earthquake shaking using the sensors in every smartphone. The app runs “silently” in the background on your phone using very little power – just like the step-tracking fitness apps. When the shaking fits the vibrational profile of an earthquake, the app sends the anonymous information to our central system that confirms the location and magnitude of the quake.
-
Product
Video Inspection Station
VIS300
-
Video Inspection Stations are available with?or without on-screen measurement capabilities?and offer?an excellent way to evaluate or test small works or items in?difficult to access locations.? As todays electronic and mechanical systems keep getting smaller, it becomes impossible to test or measure these products with traditional methods. For many applications, from development to production testing, video based inspection can help maintain quality control. Many of these systems are used in labs for development or used in production for testing production samples.
-
Product
Sarsat Distress Signal Fixed Receiver
406
-
We propose to use Sarsat Beacon Monitor 406 in seaport services, rescue marine centers, coast guard rescue centers or GMDSS rescue coordination centers. However, this system has various prospective effective use fields. SBM 406 is a wide range ground COSPAS-SARSAT signal receiver which allows to locate emergency rescue signals sent by any 406MHz beacon in local responsibility area. The device can be connected to PC or laptop, and this gives possibility to observe distress signals and beacon position data on monitor.
-
Product
Transformer Rated And Self-Contained Training Bench
Model 8803A
-
The PowerMaster® 8803A Transformer Rated and Self-Contained Training Bench uses an integrated Windows-based touchscreen interface to select and modify a simulated error scenario while located at the bench. This display is mounted on an articulating arm to maximize bench space and enable line-of-sight while standing.
-
Product
1-Watt Transmitter
VM-560FF
-
The VM-560FF Transmitter has one induction frequency; three direct connect and a fault-find frequency. The LED indicators on the transmitter show the frequency selected, output level, and battery status. An audio indicator beeps to advise the quality of the connection. This one-watt transmitter can transmit the locate signal onto the target line three ways. By direct connection, if direct access to the line is available, by induction by simply putting the transmitter in induction mode and placing it over the target line with the induction arrow in line with it or by clamp mode and using the induction clamp to clamp around the target line.
-
Product
Cable Sheath Testing and Fault Location System
Shirla
-
Cable fault location with the BAUR shirla. Shirla the fault location system is used for cable and cable sheath testing as well as for pre-location and pinpointing of cable faults. The pre-location based on the measuring bridge principle according to Murray and Glaser that is designed especially for power cables, also enables pre-location for control and lighting cables. Null balance and evaluation take place automatically.* Cable and cable sheath testing up to 10 kVC* Resistance measurement* Cable and cable sheath fault pre-location with precision measuring bridge* Adjustable cable sections that can be defined with length, conductor cross-section and material respectively and can be considered in the distance calculation
-
Product
Ground Detection and Earth Fault Location Equipment for Ungrounded or Floating DC Systems
ZX3
-
The ZX3 is a ground fault locator that finds grounds (current leakage) on a battery system positive rail, the negative rail, on both rails simultaneously, in a field device, battery bank or solar array/string, regardless if they are high resistance or low resistance or in a capacitive environment. It also can provide more information about the DC ground than any other equipment available, providing maximum analyzing capabilities.
-
Product
UPS (Uninterruptible Power Supply)
-
The UPS (Uninterruptable Power Supply) by Allied Edison is a light weight (7.2 lbs), portable, non-variable source that converts a 12 Vdc Lithium Ion battery to output 110 vac sine wave at 60 hertz. It also has four 12Vdc output jacks, and 4 USB ports to power electronic equipment such as computers or used to supply cell phone chargers, etc. It has a strong built in flashlight. The UPS plugs into a standard 120 Vac, 60 hertz receptacle for charging and indicates percent battery capacity remaining on a digital meter located on the front panel. The UPS can also be charged by a solar cell, sold separately or can be plugged into a vehicles cigarette lighter receptacle for use in remote areas. The UPS is an excellent compliment to the VS-3 power supply where a technician needs a variable AC/DC source and cannot run a power cord due to the remoteness of the work area.
-
Product
Compliance and Data Protection
-
Locate and protect sensitive and PII data to identify risk and ensure compliance. Monitor system events to identify and proactively respond to potential risks and bad actors. Simplify security operations, reduce risk and lighten security management load with automated ID and authorization cleanup.
-
Product
DM 150-Watt Transmitter
Loc-150Tx
-
The Loc-150Tx, 150-Watt DM Transmitter is used primarily with the Defect Mapper (DM) Receiver, however it is also useful for those needing a low frequency, high output transmitter. Typically, the Loc-150Tx, transmitter (DM transmitter) is used to apply a signal current to the anode bed. The pipeline returns the signal via coating faults back to the transmitter. The Loc-150Tx transmitter is designed to be powered from CP (Cathodic Protection) stations, AC or external batteries, eliminating the need for internal batteries. This transmitter has a direct connection mode to apply the locate frequency onto the conductor. There is no clamp or induction mode.
-
Product
Receiver
vLoc3-Pro
-
The vLoc3-Pro utility locator introduces new innovative tools for locating buried utilities assuring damage prevention while gathering information for analysis. With two sets of screened 3D antennas signal distortion is easily detected and displayed on the bright full color display. Along with classic locate screens the vLoc3 series locators offer new locate perspective screens of Vector Locate for fully automatic non-walk over locating, Transverse Graph showing both peak and null simultaneously providing immediate measurement of signal distortion, Plan View showing the relative orientation of the cable at any angle, and a new graphical Sonde screen with guidance arrows leading to the sonde location even when it is vertical.
-
Product
Cable Partial Discharge (PD) Spot Testing And Locating
PrecisePD
-
PrecisePD is an on-line PD Spot Testing and PD location system for Cables and Switchgear with advanced signal processing, used for the detection of PD in high noise environments.
-
Product
SparkFun GPS-RTK-SMA Breakout
ZED-F9P (Qwiic)
-
Based on the SparkFun GPS-RTK2 designs, the SparkFun GPS-RTK-SMA raises the bar for high-precision GPS and is the latest in a line of powerful RTK boards featuring the ZED-F9P module from u-blox. The ZED-F9P is a top-of-the-line module for high accuracy GNSS and GPS location solutions including RTK that is capable of 10mm, three-dimensional accuracy. With this board, you will be able to know where your (or any object's) X, Y, and Z location is within roughly the width of your fingernail! The ZED-F9P is unique in that it is capable of both rover and base station operations. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
-
Product
Mobile Problem Locator
MPL
-
The ComSonics Mobile Problem Locator (MPL) application is a smart phone application designed to provide cable technicians with a simple tool to help maintain their network. Targeted for use with ComSonics' QAM Compass via Bluetooth connection to provide contractor work verification.
-
Product
Digital Sensors
PMA-Series
-
Solar Light’s NIST-Traceable PMA-Series Digital Sensors represent the pinnacle of accuracy, durability, and selection on the market today. Our sensors measure discrete bands of the electromagnetic spectrum from the UVA, UVB, UVA+B, UVC, Visible Light, and Infrared regions. Both narrow and broad bands are available to fit any application, including germicidal requirements, environmental probes, and sensors for biologically weighted spectra (such as the erythema and CIE action spectra.) Over 135 different sensors are available in a variety of packages to fit any environment, from indoor clean rooms to harsh locations outdoors to 100 meters under water. Please note that Solar Light offers both Digital Sensors and Analog Sensors in the PMA-Series lineup. Select these Digital Sensors if you prefer to plug into our PMA-Series Radiometers to read the output of the sensor on the meter’s display. Digital models are typically used as discrete sensors that are portable and located to provide short term information. (By contrast, please select Analog Sensors if you don’t need a digital display output of the reading, if you will be connecting to your own datalogger, or if you plan to use a voltage source to provide excitation voltage to the sensor and a digital volt or amp meter to read and convert the results. Analog Sensors are typically used as process sensors that are permanently installed to provide ongoing information.)
-
Product
Sensor Technology
-
Power Monitoring and Diagnostic Technology Ltd.
PMDT is the only manufacturer to utilize all 5 types of online partial discharge sensor technology. Using multiple sensing methods ensures that PD activity is always discovered, located, and characterized. PMDT's handheld PDetector and PDStar units have more capability than the high-end diagnostic equipment of the past. The small handheld, battery powered unit can completely perform the test and analysis without the need of a PC. PDetector, PDStar, and PDiagnostic instruments feature high-resolution phase-resolved analysis of PD signals (PRPD and PRPS) in real time, so you get your test results instantly!
-
Product
Monitoring & Control Systems
-
PBE's Vantage software is designed to allow users to monitor real time data from a site remotely and accurately. Vantage allows for tracking, telemetry monitoring, alerting, and reporting of data to users. It can be configured to accept telemetry from almost any device via custom developed drivers. Capable of importing CAD maps and image files the mapping software offers a 2D GUI with icons. Vantage also offers historical playback of the data reported to replay a set timeframe. Reports are customizable and exportable to multiple common formats.The user configuration manager allows for user defined roles to grant or restrict access to and from all modules and features of those modules. The Electronic Tag Board module offers a tagging system designed to track assets that are checked in or out, while the Asset Summary module provides a list of assets with user selected telemetry streams and configurable alerts. Vantage provides location tracking and tagging, telemetry monitoring, ventilation control and reporting off data to users.
-
Product
Optical Power Meter & VFL
X0563
-
Optical power meter X-0563 combines the handheld optical power meter and the visual fault locator(VFL) functions in one unit. It can be used for the absolute power measurement and relative measurement of the link loss in dB. Its compact size, friendly operation interface, broad power measurement range, high precision and brand-new user automatic calibration function and high performance in application makes it an ideal tool for optical fiber network.
