Product

Fanout Buffers

-

Analog Devices Inc.

Analog Devices Inc.

Fanout Buffers are able to create multiple copies of input signal at their output and distribute them amaong several loads while achieving fast rise/fall time and low jitter. Input and output interfaces are CML and output voltage swing can be adjusted externally.

Product

Strain Sensors

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

Conventional strain sensors are based on strain gage technology. In order to effectively measure the strain values in a force or load measurement application, a full, 4 element strain gage bridge circuit is utilized. The configuration is known as a Wheatstone Bridge Circuit. A Wheatstone Bridge has a very linear output in it’s midrange. That being considered +100% to -100% of range. Unfortunately, a Wheatstone Bridge becomes non-linear above the upper and lower extremes of range. Therefore, significant errors can result above the end points when attempting to take precision measurements. It is particularly important to take accurate measurements in some R&D or control applications. To avoid the mentioned error issues, PCB manufactures quartz piezoelectric strain sensors that output the same mV/microstrain sensitivity throughout the entire useful range. Thus, accuracy is improved and control requirements are enhanced that may occur at positive extremes of the measurement range. The models RHM240 and model 740B02 series sensors are the strain sensors for these applications.

Product

Load Pin Products

-

Dynamic Load Monitoring Ltd.

Dynamic Load Monitoring Ltd.

DLM are world renowned for the design and manufacture of custom design load pins for a host of industries, including offshore moorings, renewable energy and marine & subsea applications.

Product

Load Pins, Tension Load Links, And Load Shackles

-

Interface

Interface

Interface’s wide range of load pins are designed for the measurement of tensile and compressive forces across a wide variety of applications, including crane/lifting, industrial, marine, offshore, and civil engineering. Machined from high tensile stainless steel, our load pins are suitable for use in exposed situations including prolonged immersion in seawater. Interface’s tension load links are designed for lifting and weighing applications in harsh environments and manufactured from high tensile aluminum and stainless steel. Interface’s load shackles are manufactured from high tensile carbon steel and the basic shackle uses the renowned Crosby G2130, G2140, and G2150 series (depending on the load rating).

Product

HV AC Voltage Test Systems

-

Fivestar HV Testing Equipment Co., Ltd.

Fivestar HV Testing Equipment Co., Ltd.

FSHV offers three different types of AC voltage test systems, the conventional type is AC test transformer design, mainly for testing objects of medium & low capacitance products, particularly for tests requiring stable voltage even if the load changes under voltage (corona, wet & pollution tests) or when the load is inductive (like inductive voltage transformers). Another is AC resonant test systems, according to series resonance circuit XL=XC (2πfL=1/2πfC), by setting F frequency of power supply or L inductance of reactor, generate a pure sinusoidal waveform of the test voltage, and the required input power is only 1/Q. Variable frequency type operates in a frequency range from 20Hz to 300Hz, ideal for field commissioning test of power cables and GIS/GIL. Variable inductance type outputs continuous AC voltage of power frequency (50/60Hz), mainly for factory testing of high and ultra-high voltage cables, power transformers, GIS, etc.

Product

Dc Load Bank

-

Junxy Energy

Junxy Energy

Highly reliable and durable new alloy resistor is used for the JUNXY DC load bank. It is thermal shrinkable and seal installed in the stainless steel pipe, whose surface with insulated heat sink. The resistor is moisture-proof, anti-corrosion, good heat dissipation, high insulation resistance, safe and reliable.

Product

Power Management

-

Schweitzer Engineering Laboratories, Inc.

Schweitzer Engineering Laboratories, Inc.

Power management solutions maintain grid stability while offering flexibility that reduces operating expenses and meets ever-changing system demands. SEL systems include comprehensive generation and load management with relays, logic, and control systems.

Product

Linear Testfixture for VPC iCon i1 Mass Interconnected Cassette Interface (Cassette Not Included) 4 or 10 Positions Blocks, UTT 306 x 248 mm

MG-02-01

-

MG Products

MG-02-01 - MG Products

FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with detachable aluminium back and bottom panels• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (2000N) 1300 units• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 306 x 248 mm (wxd)• Outer dimensions: 470 x 490 x 100 x 170 mm (wxdxh1xh2)• Designed for Mass interconnect changeable cassette• Up to a maximum of 4 interface blocks of 160 signals• All interface blocks can be customized

Product

Rod End Load Cell

-

Futek Advanced Sensor Technology, Inc.

Futek Advanced Sensor Technology, Inc.

FUTEK’s Rod End Load Cells provide an excellent solution for applications involving Inline Actuators or Hydraulic Jacks with Male/Female Threads. You will find a capacity

Product

Digital Force Gauge

-

Guangzhou Amittari Instruments Co.Ltd

Guangzhou Amittari Instruments Co.Ltd

The digital force gauge is a kind of simple and convenient multi-functional instrument for high-accuracy push force and pull force test. It is widely used in electronics, building hardware, textile, auto parts, ignition device such as lighter, fire fighting equipment, pen manufacturing, lock manufacturing, fishing gear, chemical, power machinery, scientific research institutions and other industries. For the push and pull load test, plug and unplug force test and destructive test etc.

Product

Transconductance & Transimpedance Amplifiers

-

Measurements International Ltd.

Measurements International Ltd.

0 to 100 Amps – AC, 0 to ± 100 Amps – DC, Voltage Compliance ± 5 Volts, IEEE-488 Interface, Resistive, Capacitive, Inductive Loads.

Product

Thyratrons and Accessories

-

Teledyne e2v

Teledyne e2v

Cargo scanning is a broad term which encompasses intelligent logistics, sniffer dogs and X-ray inspection. X-ray inspection systems offer rapid, non-invasive checking of manifests, detection of contraband, and when combined with other techniques, can be used to identify the presence of nuclear material. X-ray energies up to 10 MeV are required to penetrate fully loaded shipping containers and vehicles. These X-rays are generated through the acceleration of electrons along a linear accelerator into a target using megawatt energy microwave pulses produced by the RF sub-system.The skills for the design, manufacture and integration of specialised components for low-cost systems reside mainly in commercial companies. There is an emerging trend for linac system companies to demand higher performance from their integrated RF sub-systems.Currently, we intend not only to drive the innovation and development in this area, but also to offer integrated RF sub-systems to meet new requirements such as, portability, material discrimination and higher throughput.

Product

Clamping Elements

-

ACE Controls Inc.

ACE Controls Inc.

Clamping elements from the LOCKED series provide a high level of safety. These ACE products clamp and decelerate loads and are suitable for perfectly controlled holding, both linear and rotary, in all processes.

Product

Loading Adjustable Drop Tester Machine

CX-DL15A

-

Shenzhen Chuangxin Instruments Co., Ltd.

CX-DL15A - Shenzhen Chuangxin Instruments Co., Ltd.

Package Impact Drop Testing Machine is used to measure the dropping impact incidence when the package in using, transportation and decorating. Labtone "1G+" project strictly ensure the accuracy. Besides precision plane drop testing, it also can undertake edge and angle test to ensure the complete performance evaluation for the package. During the products handling or transport process, there may be drop/ fall, which results in damage within the products. And this Drop Tester simulates the drop/ fall of a finished product to evaluate the damage. All the rhombohedrons, angles and faces of the products can be tested.

Product

Turn-Key Short Circuit Laboratories

-

Hilkar

Hilkar

For low and medium voltage switchgear including :*Circuit breakers*Contactors*Disconnect switches*Fuses*Miniature circuit breakersApplied tests for low and medium voltage switchgear :*Dielectric withstand test*Impulse withstand test*Breaking capacity test*Mechanical life testElectrical life test*Over load performance test*Short circuit breaking capacity test**Short time short circuit impulse current test*Temperature rise test*Operation performance testTests for low & medium voltage panels :*Short time short circuit impulse current test*Dielectric test*Impulse withstand voltage test*Temperature rise test

Product

Modular DC Electronic Load LED Simulator

6310/A

-

Chroma Systems Solutions, Inc.

6310/A - Chroma Systems Solutions, Inc.

Chroma 6310A Programmable Electronic Load integrates microprocessor capabilities into each load module and mainframe to provide simple and accurate parallel operation to optimize the speed and control among multiple load modules. All load modules may be configured to work synchronously, to test multiple outputs simultaneously, thus simulating real life applications.

Product

DC Electronic Loads

-

Electronic Test & Power Systems

Electronic Test & Power Systems

An adjustable electronic load gives the test engineer the ability to qualify designs, check production batches or service and repair electrical products. Many applications demand an adjustable electronic load. These include the burn-in of new devices along with general power supply, battery, fuel cell and generator testing.

Product

Nano-focus X-ray Inspection System

X-eye NF120

-

SEC Co., Ltd.

X-eye NF120 - SEC Co., Ltd.

Nano-focus Tube of 400 nano resolution is installed which is specialized for Semiconductor Packaging, Wafer Level Packaging(WLP) requiring detection of Sub-micron defects.Able to trace and inspect defected area precisely by precise movement of axis with Anti-vibration table.Tomography is available if 3D CT module is added and Wafer Bump Automatic Inspection is available from loading to inspection with wafer handler systems.

Product

Drop Test Machine

-

Labtone Test Equipment Co., LTD

Labtone Test Equipment Co., LTD

Packaging drop test is used to determine the effect of impact on the package during use, transportation, loading and unloading. Thestrictly designed LABTONE "1G+” ensures its accuracy. Apart from accurate plane fall test, it can also perform edge frop and corner drop test to make a complete evaluation on the performance of packaging and product.

Product

7U VPX 1 Slot Power & Ground 25G Pass Through

101VPX701P-9X13

-

ELMA Electronic, Inc.

101VPX701P-9X13 - ELMA Electronic, Inc.

Power for 3.3V, 5V and 12V are included, rear connectors areall fully loaded, use with Elma’s slot to slot or slot to I/O bulkhead cable products during system development.

Product

Low-Barrier Schottky Diode Detector, 10 MHz to 18 GHz

8472B

-

Keysight Technologies

8472B - Keysight Technologies

The Keysight 8472B Low-Barrier Schottky Diode (LBSD) detector has been widely used for many years in a variety of applications including leveling and power sensing. It offers good performance and ruggedness. Matched pairs (Option 001) offer very good detector tracking. A video load (Option 002) extends the square-law region to at least 0.1 mW (-10 dBm).