Contacts
See Also: Modules, Wire, Connectors, Patchcords, Flying Leads
-
product
600A Digital Clamp Meter
7128B
Peaceful Thriving Enterprise Co Ltd
This is a auto-ranging, high accuracy and stable hand held clamp meter to make electrical maintenance safe and easy. With special designed IC to support true RMS, the meter is available to measure AC/DC voltage to 600V, AC current to 600A and resistance to 60MΩ; also having the capability to test diode, continuity and non contact voltage sensing. Sub switch included Function Select, Max-Min Indication, Value Hold, Range Select, Relative Value Measurement, Inrush Current Indication, Illumination and Back-light.
-
product
Tool, Extraction, 75 Ohm and 20/26 GHz Coax, Receiver and ITA
910112117
Tool, Extraction, 75 Ohm and 20/26 GHz Coax, Receiver and ITAThis extraction tool is used to extract 75 Ohm and 20 GHz coax contacts from receiver and ITA modules.
-
product
Handheld Tachometers
The handheld tachometer is a means of measuring revolutions within the industrial sector, either optically or mechanically. The handheld tachometer can be used for maintenance and calibration of machines that have moving parts. The principle is similar to a bicycle speedometer, where time will be measured until a wheel has completely turned. The handheld tachometer has two different measurement methods.The handheld tachometer may have a contact connection to the moving parts. Alternatively, the handheld tachometer works with reflecting marks. This will be secured on the moving part. As the laser strikes the reflecting mark during rotation, it will be reflected and detected in the handheld tachometer via a sensor. Rotation speed and speed can be seen on the handheld tachometer. The handheld tachometer may combine both possibilities (contact and non-contact connection). Next to the handheld tachometer you find other devices for measuring revolutions at PCE Instruments.
-
product
Dual 8x8 1-Pole High-Density PXI Matrix Module
40-520-207
The 40-520 family of high-density PXI matrices is available in 22 different configurations with up to 256 crosspoints. The choice of six bus widths (x16, x12, x8, x6, x4 and x2) enables competitively priced solutions using Pickering Electronics instrumentation quality reed relays. These relays offer very long life with good low-level switching performance and excellent contact resistance stability. Typical applications include signal routing in ATE and data acquisition systems.
-
product
Phase Sequence Indicators (Contact Type)
855 PR
Standard Electric Works Co., Ltd
● Two functions in one unit: open phase and phase sequence detection.● Lamps let you determine at-a-glance if phase is open.● Large size alligator clips for easy clipping onto switch-boards terminals.● Checks a wide range of 3-phase power sources.● Special test leads length are available on request.● Push button switch is designed to minimize damage due to negligence.
-
product
Diode Scanner
SC924
Frothingham Electronics Corporation
The SC924 is an electromechanical device for testing diodes loaded on burn-in boards.A set of Kelvin contacts is indexed from diode to diode. The contacts move over a range of 24 inches in the X direction and the table holding the boards moves over a range of 9 inches. This allows scanning of multiple burn-in boards or boards with multiple rows of diodes.
-
product
Infrared Thermometers
PeakTech Prüf- und Messtechnik GmbH
Infrared thermometers offer many advantages when measuring surface temperatures because they have a much faster response time than conventional contact thermometers and it is possible to record precise measurement results in fractions of a second.
-
product
PCB Connectors
Smiths Interconnect offers a broad range PCB connectors for harsh environments. A wide choice of configurations and terminations of signal, power, high speed, RF contacts and spring probes solutions.
-
product
16 Relay Output PCIe Board, 8 Isolated Digital Input Channels, 24V
APCIE-2200-16-8
8 electromechanical relays with change-over contacts The PCI-Express 16 relay board APCIe-2200-16-8 has 16 relay output channels and 8 isolated digital inputs, 24 V. 7 inputs are interruptible. The board is especially suited for applications like industrial I/O control, signal switching, alarm monitoring, as interface to machines, for the ON/OFF monitoring of motors, lights etc. in the harsh industrial environment.
-
product
6 Contacts- Circuit Breaker Analyzer
CB14
The CB14 is a 6 contacts circuit breaker analyzer designed to perform Timing, Motion as well as Static & Dynamic Resistance Measurement (DRM) in a single test. It also includes 3 multifunction analog inputs.
-
product
DIO-AIO Conversion Set For Conventional Power Amplifier
PAD64
PAD64 DIO(digital input/output)-AIO(analog input/output) Converter is the equipment which could be used for DI/DO (Digital input/Digital output) conversion and galvanic isolation between Real-time simulation system and protection equipment, and any other equipment which need AIO (analog binary input/ output, dry contacts).
-
product
McMurdo FastFind - Wrist Lanyard
10-91-060-001A Fast Find 210
10-91-060-001A Fast Find 210 - standard model with GPS for extra fast position location Announcing the amazing new McMurdo FastFind Satellite Personal Locator Beacon (PLB): the most compact, waterproof and versatile 406 MHz emergency location beacon available on the market today.The Fast Find is a 406 MHz Personal Location Beacon (PLB) that should be carried by individuals, who are embarking on trips into areas around the world where there is little or no other forms of communication or where other forms of communication are unlikely to work. The Fast Find acts as your personal Emergency Location Beacon, it is your last resort communication to the national and international search and rescue bodies and it should not be misused. The Fast Find is designed as a direct communication, to the 406 MHz Search and Rescue satellite system, its signal indicates that you are in need of urgent response and assistance. The location of a McMurdo Fast Find 210 GPS PLB can be determine to a typical positional accuracy of about +/- 62 metres (0.03 miles) within a few minutes of PLB activation. McMurdo FastFind PLB Manual (.pdf)Its small size belies its rugged construction and powerful output. There is no compromise. Once activated, the distress beacon will send out a signal for help, and continues to transmit for at least 24 hours, at a powerful 5 watt output, ensuring that your call for help gets through whatever the conditions. The pocket sized beacon transmits at the press of a button, to alert search and rescue services to your plight.McMurdo FastFind PLB is an essential piece of life-saving equipment, weighing in at just 5.3 oz (150g) and having the size of an average mobile telephone (actual dimensions being 1.34”/34mm x 1.85”/47mm x L 4.17”/106mm) it will slip into the smallest pocket or backpack compartment. The user can activate it in the most remote locations around the world: on land, at sea or in the air, and can be confident of being able to contact the world’s professional search and rescue services directly if they are to encounter a possibly life-threatening situation.McMurdo FastFind PLB comes equipped with an integral 50-channel GPS system and complies with rigid federal and international standards. It operates on the global COSPAS SARSAT 406MHz search and rescue satellite communication system, so a call for help will be acted upon…and fast. The McMurdo FastFind PLB is subscription FREE and does not rely on any commercial call centers. THE McMurdo FastFind PLB model transmits two signals simultaneously: a global 406 MHz signal and a 121.5MHz local signal. Once activated, McMurdo FastFind PLB’s signals will continue to transmit for at least 24 hours, at a powerful 5 watt output, the 406 MHz transmission ensures that a call for help gets through, no matter what the conditions. McMurdo FastFind PLB also includes a unique flashing SOS LED light to further assist in speeding up the user’s recovery time during night rescues.McMurdo FastFind PLB will operate in temperatures as low as -20°c and its integral battery has a user storage life of 5 years, so there’s no need for frequent battery changes or re-charging.Put a McMurdo FastFind PLB in your pocket, and get found fast.
-
product
Exchangeable Test Fixture
MA 2112/D/H/S-7/GR2270/71
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 12,13 kg
-
product
GPIB to Relay Interface Boards
Model 4864 OEM
* 114521-11 Board provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully IEEE-488.2 and SCPI compliant.* Fully IEEE-488.2 and SCPI compliant.* Includes 50-pin mating Relay connector and serial header connector.* Optional terminal board for easy connections without soldering. See the GPIB Accessory page.* Operates on 12 to 24 Vdc power.* Use an ICS GPIB Connector/Address Switch Assembly to mount a GPIB connector and Address Switch on the rear panel. • 114521-12 Board provides 16 heavy duty form A contacts (SPST).* All other specifications are the same as for the 114521-11 Board. * 114521-14 provides 16 Relay driver outputs that sink 300 mA.* All other specifications are the same as for the 114521-11 Board.
-
product
Kelvin Contact Spring Probes
We have spring probes for Kelvin contact, which best suits to use for sensitive and extremely precise test. It is used by contacting to one terminal of semiconductor by two probes. We have 0.3, 0.4 and 0.5mm pitch probe for Kelvin contact.
-
product
Digital H.V. Insulation Tester(5kV)
6304 IN
Standard Electric Works Co., Ltd
● 2 Lines × 16 Characters LCD● Microprocessor-controlled● Tests insulation resistance up to 10 TΩ● 4 Insulation test voltages: 500V, 1000V, 2500V, 5000V● AC / DC Voltmeter (30~600V)● Short-circuit current up to 1.9mA● PI (Polarization Index) indication● DAR (Dielectric Absorption Ratio) indication● Auto-ranging on all insulation ranges● Optical USB to RS-232 data transmission● Well isolated from contact● Well protected from surges● 2 built-in optical LEDs for data transfer● Visual and audio warning of external voltage presence (≥30Vac or ≥30Vdc)● Auto-hold function to freeze reading● Overload protection● Adjustable testing duration: 1~30 minutes● Internal memory for data storage● Displays testing duration for insulation measurement● Auto-off function● 200 measurement results can be saved in memory and recalled on display
-
product
Doide Testers
Specialized test for Axial, SMD and 2-pin package type.Electrical Testing: Forward:VF Reverse:VZ、DVZ、IR、ACIR、DIRFour-wire measurement and contact resistance in case of deviation.Manual test or conjunction with automatic machine.
-
product
Proximity sensors
Voltage 0...250V DC, 230 V AC Cable length 0.3, 2.5, 5, 7.5, 0.2...10 m Plug connection M8, M12 / female thread M5 Electrical Via reed contact Contactless PNP, NPN Pneumatic.
-
product
Phase Sequence Indicators (Contact Type)
855 PRA
Standard Electric Works Co., Ltd
● Two functions in one unit: open phase and phase sequence detection.● Lamps let you determine at-a-glance if phase is open.● Large size alligator clips for easy clipping onto switch-boards terminals.● Checks a wide range of 3-phase power sources.● Special test leads length are available on request.● Push button switch is designed to minimize damage due to negligence.
-
product
Pressure Indicating Film
Prescale
Prescale film is used to measure contact pressures. The film structure consists of micro-encapsulated color forming and developing material. When pressure is applied to the film, a red color impression is formed in varying density according to the amount of pressure and pressure distribution.
-
product
Laser Head
5517D
The Keysight 5517D is used primarily in VME and PC based laser interferometer systems where the velocity of motion is faster, such as semiconductor lithography and flat panel applications. Please contact Keysight for custom requirements.
-
product
Safety Critical Miniature Relays
CU-U Series
The CU-U is a so called safety relay which is used in places where a safe separation between coil and contact circuit is required. The relay is, with the corresponding screw socket V12, according to CEE 15/2e edition, approved by KEMA, for application in gas fired installations.
-
product
Milliohm Meter
MO-100
Diagnose potential failure with the MO-100, portable battery powered milliohm meter. Quickly check windings opens or shorts in motors, generators and transformers, wire-to-wire connection resistances, heating elements testing and contact resistance in critical electrical connections.
-
product
Signal, Contact, ITA, TriPaddle, Round Post, PCB Mount
610110000
Primary mating contact 610110179. (May mate with other ITA contacts, as well.)Specifications Operating Voltage & Current 5 Amps Max. Continuous (20 AWG)600 Volt Max. use of wire Mil-W-16878/4Contact Resistance 4 mOhms Max.Measured at 50 mV @ 100 mAAVG Mating Force(lbs) 0.41Dielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 4000 MOhms Min.Contact Body BeCuContact Plating 30µ” Au over 100µ” NiCycle Life 20,000 Cycles
-
product
PXI 6U PXI High Density Matrix, EMR 132x8
45-542-001
The 6U PXIMatrix Module 45-542 is a very high density electro-mechanical relay matrix available in 132x8 format with 1 pole switching. Typical applications include signal routing in Functional ATE and data acquisition systems. The matrix is constructed using high reliability 2A electro-mechanical relays, offering >10e8 operations (under low power loads) to give maximum switching confidence with long life and stable contact resistance.
-
product
Contacting Extensometers
AMETEK Sensors, Test & Calibration
The contacting extensometers are designed for accurate strain and extension measurement of a material up to a maximum sample thickness of 25 mm.
-
product
Portable Digital Manometer
PS309
Featured are an integral variable reluctance transducer, solid state electronics module, 3 digit liquid crystal display (LCD)* and battery pack with six 1.5V penlight cells for truly portable operation. The units can also be powered from an external DC power supply or AC battery eliminator (converter) module. The transducer features all corrosion resistant materials in contact with the pressure media (both ports in differential units), very low internal cavity volumes and ultra-low volumetric displacement with full-scale pressure excursion. Transducer calibration is unaffected by dielectric properties of the sensed fluid. Gauge and differential transducers may be disassembled and range changed by simple diaphragm replacement.
-
product
Test-Stand Software for TD6 Controller for QMax ATE
TD6 TestStand Software
Qmax Test Technologies Pvt. Ltd.
The TD6 TestStand will enable the users to sequence and execute their own test programs. The user can browse his/her test program and add it to the TD6 TestStand component. The test program can either be in the form of DLL ( Dynamic Link Library ) or EXE ( Executable ). And, the user can add any number of steps. As of now, we will support only the .Net based test programs. Each and every individual assembly or exe added in the TestStand component will be considered as a single step. All such steps on the whole added in the TestStand component will be considered as 'Sequence'. The same is priced at Rs. 8,42,520.00 plus GST @18% extra. For further details, pls contact sales@qmaxtest.com





























