Clamps
-
Product
Clamp type AC Current Sensor/for Power Monitor
ZCT-23
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Compact size*AC 0.1A~120A*Current measurements of terminal feeder
-
Product
Clamp Meter, Auto, Average, 1 kA AC, 600 V AC, 600 V DC, 46 mm Jaw Opening Max.
72-6130
-
A clamp-on type test meter with AC/DC voltage and AC current measurement.
-
Product
24V Heavy Duty Circuit Tester
27430
-
Heavy duty probe, cord and clamp. The probe is insulated with high-visibility shrink tubing to prevent the possibility of shorting the side of the probe to other components. Comes with a strain relief spring on the cord.
-
Product
Clamp type AC Current Sensor/with DC Voltage Output
ACT-5H
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*For current measurements of the control board*AC 0.1A~5A*DC 5V full scale output
-
Product
Diesel Engine Tachometer
GE-1400
-
Handheld type digital engine tachometer to be designed for dedicated r/min measurement of 4-cycle diesel engines. R/min direct reading measurement is available only by clamping a CP-044 Diesel Engine Rotation Sensor (sold separately) to a fuel injection pipe.Both analog (switchable between analog and monitor output) and pulse outputs are provided; enabling to use analog output for data recording (monitor output for sensor waveform checking or analysis input signal of FFT analyzer), and to use pulse output for tracking analysis signal of FFT analyzer.
-
Product
Clamp Meter
-
It can be used for CURRENT, VOLTAGE and FREQUENCY measurements on installations of surge voltage.
-
Product
Ammeter According to DIN EN 61010-1 (VDE 0411-1)
-
PeakTech Prüf- und Messtechnik GmbH
Is a measuring device for AC and DC currents up to 1000 A using a current clamp for conductor diameters up to 48 mm. Current and voltage measurements are carried out as true RMS (true rms value) measurements, which means that the measured values are displayed correctly even with waveforms that deviate from a sine wave.
-
Product
ELECTRICAL TEST Kit
1021 TK
-
Standard Electric Works Co., Ltd
2950 CL ● Pocket size.● 4000 counts.● Full automatic measurement : Voltage measurement. Current measurement. Resistor measurement.● Data hold function.● Continuity check.● Diode measurement.● Select function.● Low battery indication.● Auto off function.● Flashlight (auto off in 1 minute). ALS-2 ● Use with any clamp meter.● x10 mode allows for more accurate measurements of low amperage devices.● x1 mode allows for direct reading.● 4mm voltmeter input jacks.● Integrated ground conductor.● 10 amp capacity.● 10cm plug cord for greater flexibility.
-
Product
AC Digital Clamp Meter
SK-7615
-
Up to 400A AC, Conductor dia. : φ26mm max, Round clamp head for accurate measurement.
-
Product
Pneumatic Contact, ITA, Ferruless Fitting, for 3/8" OD, 1/4" [9.5 x 6 mm] ID Tubing
610132101
Pneumatic Contact
Primary mating contact 610131101.Pneumatic Connectors are available with either ferruless polytube fittings (3/8" tubing OD) or hose barb (3/8" tubing ID). Ferruless fittings securely attach tubing without hose clamp - which is recommended for the hose barb type (hose clamp not included). The 1/8" ID connectors are available with hose barb.
-
Product
200A Digital Clamp Meter
7128A
-
Peaceful Thriving Enterprise Co Ltd
This is a auto-ranging, high accuracy and stable hand held clamp meter to make electrical maintenance safe and easy. With special designed IC to support true RMS, the meter is available to measure AC/DC voltage to 600V, AC current to 200A and resistance to 20MΩ; also having the capability to test diode, continuity and non contact voltage sensing. Sub switch included Function Select, Max-Min Indication, Value Hold, Range Select, Relative Value Measurement, Illumination and Back-light.
-
Product
ITA, ICon, With Protective Cover
410123101
ITA
The iCon ITAs small width and inboard handle allow for easy side-to-side stackability. The u-shaped cable clamp allows modules to be pre-wired before assembly and offers a maximum cable bundle diameter of 1.21". The slide-off cover allows easy access to wiring for maintenance and probing.
-
Product
AC/DC Clamp Meter
3904 CL
-
Standard Electric Works Co., Ltd
● 4000 - count LCD.● Full automatic measurement. ◎ Voltage measurement. ◎ Current measurement. ◎ Resistor measurement. ◎ Capacitor measurement ◎ Frequency counter.● Range change function.● Data Hold function freezes the reading.● Continuity check.● Diode measurement.● Low battery indication.● Auto Power Off (APO) function.● Safety design throughout with no exposed metal parts, shielded banana plugs and recessed input terminals.
-
Product
400A Dual Display Clamp Meter w/ Test Lead Storage
DL569
-
UEi Test & Measurement Instruments
Dual Display 400A Clamp Meter w/ Test Lead Storage
-
Product
True RMS Wireless Clamp Meter w/ Differential Temperature & DC Amps
DL429B
-
UEi Test & Measurement Instruments
The DL429B Clamp meter offers users True RMS precision, dual temperature, a voltage and amp range that will extend applications to ECM motors, variable speed DC motors, plug and play DC motors and AC ductless mini splits. It also has Wireless capability and a free App.
-
Product
Steering Test Equipment: Software & Hardware
-
MB Dynamics delivers steering test equipment to help fulfill a myriad of application test requirements, or jobs-to-be-done. The steering test equipment consists of software for multi-test-head, synchronized MIMO closed-loop control and data acquisition; rotary servo motors for attachment to a steering spline or wheel; electrodynamic shaker systems; long-stroke linear motor actuators; pneumatic actuators; column stands for mounting steering column; gear fixture for mounting the gear; instrumentation (force, torque, displacement, rotary position, acoustic, acceleration); fixtures for mounting gears and columns; brackets, clamps, and fixtures for holding test items; jounce/rebound fixtures and tilt positioners for aligning input forces with tie rods at angles; software and associated data acquisition hardware up to 16 channels for recording, analysis and evaluation of in-lab steering noises and accelerations, road load data acquisition, and general Sound & Vibration analysis; and engineering services to accelerate test effectiveness.
-
Product
Clamp type AC Current Sensor/for Load Current Measurements(CT Series)
CT-33S
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Ultra compact size*AC 1A~200A*Current measurements of feeder
-
Product
Wireless Connectivity AC / DC Clamp Meter with 6000 count / NCV / SPT / 600A AC / DC Current
MS-W366D
-
This is a external wireless connectivity Digital Clamp Meter integrated with AC / DC hall effect sensor / 6000 Count, True RMS, auto and manual measurement.
-
Product
1-Watt Transmitter
VM-560FF
-
The VM-560FF Transmitter has one induction frequency; three direct connect and a fault-find frequency. The LED indicators on the transmitter show the frequency selected, output level, and battery status. An audio indicator beeps to advise the quality of the connection. This one-watt transmitter can transmit the locate signal onto the target line three ways. By direct connection, if direct access to the line is available, by induction by simply putting the transmitter in induction mode and placing it over the target line with the induction arrow in line with it or by clamp mode and using the induction clamp to clamp around the target line.
-
Product
ITA, ICon XL, 2 Module, Extra-Large Backshell, EMI
410123232
ITA
The iCon XL offers an extra-large u-shaped cable clamp that can hold cable bundles with an oblong bushing effective diameter of 1.95" and offers a cable bend radius of 1". A slide-off backshell allows easy access to wiring for maintenance and probing. The iCon XL also offers EMI shielding.
-
Product
Phase Detector/ Rotary Field Indicators
-
Shanghai Beha Electronics Co., Ltd.
*The test instruments are built in compliance with the most recent safety regulations and ensure safe and reliable testing.*Display of all three phases via LCD-Segments*Display of phase rotation direction via LCD-Segments*Including measurement leads with safety Crocodile Clamps*with built-in fuses
-
Product
TRUE RMS AC Clamp Meter
2960 CL
-
Standard Electric Works Co., Ltd
● True RMS measurement.● Pocket size.● 4000 counts.● Full automatic measurement. Voltage measurement. Current measurement. Resistor measurement.● Data hold function.● Continuity check.● Diode measurement.● Select function.● Low battery indication.● Auto off function.● Flashlight (Auto off in 1 minute).● Re-power on by pushing any of the push buttons or by changing the rotary switch mode after auto power off.
-
Product
Backshell, iCon, Receiver, with Large Cable Clamp
310113794
Backshell
This receiver backshell is used with the iCon Receiver and is not mounted to a rack or panel. It provides protection for exposed wiring and is ideal for use together with the iCon ITA for cable-to-cable applications.
-
Product
ITA, G6, 6 Module, With Protective Cover
410104273
ITA
This G6 ITA is equipped with a removable EMI-shielded backshell. This backshell slides up to provide access to wires and connectors. This ITA also includes a keying feature. Removable and adjustable U-shaped cable clamps are attached by screws to the ITA frame and allow ITA modules to be pre-wired before assembly. The clamps can hold cable bundles with an oblong bushing effective diameter of 1.59". ITA strain relief plates are not needed.
-
Product
Mechanical Wedge Action Grips
2716 Series
-
The Instron mechanical wedge action grips are durable tensile grips designed to automatically increase clamping force as test loads rise, maintaining fixed jaw positions and preventing slippage. Their open-front, moving-body design allows easy specimen insertion while ensuring consistent gauge length and minimal compressive force during clamping, making them a versatile gripping solution and particularly suitable for testing high-strength materials such as metals and composites.
-
Product
78-Pin D-Type Female Breakout DIN Rail
40-967-078-F
-
This termination option is capable of accepting heavy duty connection wires and uses rising clamp screw terminals to minimize the danger of copper strand damage. Users should care take to protect the termination, provide a suitable method of restraining the cables, and ensure appropriate electrical safety precautions are observed.
-
Product
Cable Clamp Kit, iCon, ITA
410118115
Cable Clamp Kit
Cable Clamp Kit, iCon, ITAThe iCon cable clamp kit includes the ITA front plate, clamp housing, and the cable clamp. Accompanying housing and cable clamp screws are provided. VPC offers an adjustable U-shaped cable clamp to accommodate for larger wire bundles to support high speed and high power applications.For more information, please contact one of our Field Application Engineers.
-
Product
3-Phase Power and Energy Analyser
PQ55A
-
* Cpmprehensive real-time monitoring, recording and analysis of 3-phase systems* Voltage measurement (true RMS)* Current measurement (true RMS)* Power factor measurement* Phase angle measurement* Power analysis (active, apparent and reactive power)* 4. Current clamp for neutral line current measurement* Suitable for use in housing construction, offices and small businesses
-
Product
ITA, I2 Micro ICon, 168 Position, With Oversized Backshell
410130106
ITA
The i2 Micro iCon ITA with oversized cable clamp is capable of holding up to 168 QuadraPaddle contacts. With a wider 1.97” footprint, it is ideal for applications requiring shielded twisted pair wiring or other wire types with oversized jackets. The 30-degree u-shaped cable clamp allows ITA modules to be pre-wired before assembly and can hold cable bundles with an oblong bushing effective diameter of 1.80". The removable cover allows easy access to wiring for maintenance and probing. Integrated spring locking tabs ensure even and secure engagement.





























