Cages
-
product
Airlock Control System
The system is built on the basis of a panel computer with a touch screen, performing the functions of a user interface and recording the measured parameters. The stand is equipped with gate drives and a set of sensors (pressure, flow rate, force). Real-time gate control is implemented on the basis of the R-series board; for input and conversion of analog signals from the sensors, an expansion cage of the cRIO-9151 R-series boards is used.
-
product
CPCI Test Extender 6Ux400mm
117EXT6116-0XXX
The cPCI extender boards are designed to bring a circuit card completely out of a card cage or enclosure so that it can be tested or debugged on each 2mm HM connector in P1-P5. Each line in rows A-E can be isolated with the DIP switches.
-
product
Analog Output Module, 16-bit D/A
IP231
The IP231 outputs analog voltage signals to drive up to 16 devices. When used with a carrier that holds four IP modules, up to 64 voltage outputs can be obtained from a single card cage slot.
-
product
Crowbar Resistors
Crowbar resistors are three phase resistance banks which are connected to the rotor windings of the DFIG (Doubly-Feed Induction Generator) such as wind power generator. They are used to prevent damage to the inverter circuits attached to rotor side when a fault occurs in the grid. DFIG power converter, which has a restricted over-current limit, needs special attention during faults in the grid. If the rotor current or DC link voltage reaches the threshold value, crowbar resistors disconnect the converter in order to prevent the generator turning into a squirrel cage induction machine. By crowbar resistors, the DFIG could stay connected to the grid and continue its operation.
-
product
VXS Type 32V, w/plug in PSU
32V05LY348Y3VGE0
VXS Type 32V family of enclosures provide a lightweight, tower platform for packaging portable VITA System applications. Designed to VITA & IEEE. Systems can be configured with or without rear I/O card cage.
-
product
Signal Evaluation Systems
*Integrated flow, temperature and wire monitoring*Adjustable switching outputs for monitoring flow and temperature*Clearly visible multi-color LED bargraph display*Signal output via potential-free relay contacts*Connection options: Insulation displacement / screw terminals and cage clamps
-
product
68-Pin VHDCI Connector Block, Female With Backshell
B068VFR-6F-0A
This connector block provides a simple method of connecting to high density 68 Way VHDCI connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. The metal shell includes an internal insulation barrier under the carrier board.
-
product
Multi-Truck Steri-Dry™ Sterilizer
The Gruenberg Steri-Dry™ Dry Heat Lab Animal Science Sterilizer provides the lab animal science market with equipment to sterilize habitat cages through the process of dry heat sterilization. Gruenberg dry heat sterilizers are designed for lab animal science applications.
-
product
68-Pin SCSI Micro-D Male Connector Block
92-965-068-M
This connector block provides a simple method of connecting to 68-Pin SCSI Style Micro-D connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage.
-
product
Magnetic Level Gauge Switches
ABB's magnetic level gauge switches for point level alarm and/or control can mount to a KM26 magnetic level gauge or an LS Series cage level switch.These switches are completely isolated from the process fluid as they are magnetically activated by a magnet equipped float (KM26) or attraction sleeve (LS Series). The unique magnetic coupling action eliminates seals, diaphragms, springs, and torque tubes common to other level switching alternatives since there is no physical contact with the process fluid. The magnetic coupling also eliminates process connections to the switch; therefore, no isolation valves are required to block off the switch for maintenance. The switch "set point" is easily adjustable without changing any process piping and the result is a more reliable and easier way to maintain level system.
-
product
200-Pin LFH Connector Block, Female
B200LFR-2F-5B
Suitable for use on the front of PXI modules this connector block provides a simple method of connecting to high density 200-Pin LFH connectors. The screw terminals use a rising cage screw clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximise copper cross sectional area and insulation properties.
-
product
VME Test Extender 6U/220mm 64X with P0
116EXT6122-0125R
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
product
5 Slot VME64 Portable Tower Development Platform
32V05MMX36N3VCC0
Elma Type 32V with superior cooling and accepts 6U cards mounted vertically with or without rear I/O card cage, VITA & IEEE standards, heights are 63HP and 84HP (HP=.2”) and widths 3U, 4U and 6U.
-
product
VME Test Extender 9U/400mm J1/J2/J0
111EXT9140-0120
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
product
Heavy Load Ball Screw with Caged Ball Structur
HBN
Heavy Load Ball Screw with Caged Ball Structure. Heavy load ball screws with the caged ball structure (HBN model) drastically improve the rated load compared to the conventional products by utilizing the optimum internal structure for use in heavy load condition. In this model, the caged ball structure is adopted between balls to eliminate collisions and mutual frictions of the balls and improve the lubricant maintenance. This modification brings about a longer lifetime under heavy load conditions.
-
product
Type 12R2, 8U, 19" Rackmount, MIL-Rugged, Top Load
12R2-8U-TL
The 8U, 12R2 is designed to meet the harsh environment of shipboard, airborne, and ground mobile applications per MIL-STDs. Shock isolated versions are designed to attenuate 25G shock inputs to the chassis to less than 10Gs at the card cage.
-
product
68-Pin SCSI Micro-D Connector Block
44-965-068-F
Suitable for use on the front of PXI BRIC modules this connector block provides a simple method of connecting to high density 68-Pin SCSI Style Micro-D connectors. The screw terminals accept wires up to 20 AWG and use a rising cage screw clamp mechanism to minimize risk of copper strand breakage. The metal shell includes an internal insulation barrier under the carrier board.
-
product
9-Pin D-Type Connector Block
92-965-009-M
This connector block provides a simple method of connecting to 9-Pin D-Type connectors. The screw terminals use a rising cage screw clamp mechanism to minimize risk of copper strand breakage.
-
product
160-Pin DIN41612 Shielded Connector Block, Female
40-965-160-F
The 40-965-160-F connector block provides a simple method of connecting to high density DIN41612 connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. The metal shell includes an internal insulation barrier under the carrier board.
-
product
VME Test Extender 6U/400mm J1/J2
111EXT6140-012X
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
product
VME Test Extender 3U/400mm J1
111EXT3140-11xx
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
product
68-Pin SCSI Micro-D Female Connector Block
92-965-068-F
This connector block provides a simple method of connecting to 68-Pin SCSI Style Micro-D connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage.
-
product
Autopilot Directional Gyroscopes
4000C/D-series
The 4000C/D is an air-driven directional gyro with A.C. autopilot pickoffs. Left turns produce clockwise dial rotation and right turns produce counter-clockwise rotation. Two knobs control the gyro. The left knob is used to cage the unit, and the right knob is used to select the instrument’s heading. To change course, the right selector knob is pressed and turned to disengage the dial shaft and set the pointer to a new heading. Releasing the selector knob re-engages the pointer with the dial shaft. As the aircraft turns onto a new course, the pointer returns to its original position. The on-course position of the pointer is always at the top of the azimuth circle (0° on the dial with the aircraft headed north).
-
product
Antenna Rotator
PRO.SIS.TEL
This manual cover installation on a mounting plate inside a tower or a rotator cage with a thrust bearing. The rotator consists of a rotator and a control box unit.
-
product
Rack Mount Hawk/PC Chassis
9381
A slide-in replacement for a Nova/Eclipse. A 10.5 inch (267 mm) high chassis with a 5-position Nova/Eclipse backplane and card cage, 450 watt power supply, cooling and rack slides. Accommodates up to five DG-compatible 15" x 15" (381 x 381mm) boards, a PC motherboard, diskette drive and up to three visible half-height disk drive bays and one internal half-height drive bay.
-
product
VME Test Extender 9U/220mm Universal
110EXT9122-0000
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
product
Small Form Factor (SFF)
The modular design of the Mini ATR platform allows for various configurations. The chassis can easily be scaled up or down while using the same side walls. DC and AC power variations as well as custom front I/O configurations are available. Elma also offers a wide selection of backplanes in various architectures and has different milled card cage sizes off-the-shelf.
-
product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-01 And WMA-01LF
The Falco Systems WMA-01 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-01LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
product
Electrostatic Potential Monitoring Device
electrostatic potential monitoring device that has an interface for connecting our potential sensors EMS-01 / EMS-01A / KS-2100 and measures static electricity in real time. It is possible to monitor static electricity with simple The compatible potential sensor EMS-01 / EMS . With SD card support, measurement data and alarm history can be collected with a time stamp. Operation using the touch panel display and screen display, and to notify and manage the measurement status with multiple control outputs. ...-01A Has Passed The Intrinsically Safe Explosion-Proof Structure Certification In Combination With The Safety Cage KS-301A, And Can Be Used In A Dangerous Atmosphere.
-
product
Low Voltage DC / Battery Powered High Voltage Amplifiers
WMA-005 And WMA-005LF
The Falco Systems WMA-005 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-005LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
