-
product
COM Express Type 6 Development Kit
COM Express Type 6 Starter Kit Plus
The Type 6 Starter Kit Plus consists of a COM Express Type 6 module with ATX size Type 6 reference carrier board that offers one PCI Express x16 slot with proprietary pinout for DDI adapter card that convert DDI signal to DP or HDMI signal, one PCI Express graphics x16 slot, one PCI Express x4 slot, three PCI Express x1 slots, Serial ATA, VGA, LVDS, USB3.0/2.0, Gigabit LAN and Super I/O. All necessary cables are included.
-
product
Extensometers for Indirect Tensile Testing of Asphalt
Model 3911
Jinan Testing Equipment IE Corporation
For indirect tensile testing, such as for resilient modulus, these extensometers measure the lateral deformation of specimens. They are self-supporting on the sample and clip on in seconds. The traditional way this deformation has been measured was prone to errors caused by slight rocking of the sample as it is loaded. The self-supporting design of the Model 3911 eliminates this problem. This unit will handle the dynamic pulse requirements of resilient modulus testing.The speed of mounting makes test set-up much faster than with the older method. The pivot mounting used ensures that the specimen contact pads meet the often uneven asphalt surface as well as possible. The measuring range options available allow a wide range of testing, yet can easily measure the sometimes very small displacements required.The Model 3911 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
product
Audio Circuit Tester
25500
Handy device for locating short and open circuits. Horn sounds when circuit is complete. Long 5 foot leads permit technicians to work around corners, under dash boards and in trunks. For use on all 6 and 12 volt circuits.
-
product
Interfacing Components
Spring contacts and lands for PCB interconnection and a wide range of data, power and battery charging applications including: charging batteries in portable instruments power and data transfer pins in a docking station integral compliant contacts, such as for an antenna contact in a mobile phone board to board spring contacts for use in computerised gaming systems and telecommunications units
-
product
EBX & 5.25" Single Board Computers
Advantech's EBX and 5.25" embedded single board computers (SBC) measure 203 x 146 mm and feature rich I/O choices and super-slim compact designs with multiple expansion options. These offer scalable x86 performance for low-power Intel Atom™ processors through to high-performance Intel Core™ i processors.
-
product
1100-Channel GSM Channelizer wih Quad A/D - PCIe
Model 78663
Model 78663 is a member of the Cobalt® family of high-performance PCIe boards based on the Xilinx Virtex-6 FPGA. This fourchannel, high-speed A/D converter with1100 GSM DDCs (digital downconverters) accepts IF signals from an RF tuner. It is ideal for capturing all transmit and receive signals in both upper and lower GSM bands.
-
product
3-Ch 200 MHz A/D with DDC & 2-Ch 800 MHz D/A with DUC, Virtex-7 FPGA - PCIe
Model 78721
Model 78721 is a member of the Onyx® family of high performance PCIe boards based on the Xilinx Virtex-7 FPGA. A multichannel, high-speed data converter with aprogrammable DDC, it is suitable for connection to HF or IF ports of a communications or radar system. Its built-in data capture and playback features offer an ideal turnkeysolution.
-
product
Cable Testers
Passage test:Detects open wires, short circuits and faulty wiring. Pass / fail test using a given pattern cable. Finding intermittent connections.Save cable data for documentation purposes. Print wiring diagrams. Printing labels. Log and print error logs.Graphical representation of the wiring of cables, graphical comparison of two cables. Easy, intuitive, graphical tracking of individual wires of a cable.Quickly install quick-mount boards for a variety of connector types such as BNC, RJ45, Sub-D, flat-ribbon connectors, and many more.Easy connection to the PC via USB .Light Director System:LED-led assembly of connectors. Optional also with voice output. High degree of safety due to fault checking during assembly.
-
product
Motion Control Terminal Board for Mitsubishi J2S-A Servo Amplifiers
DIN-814M0
This well-designed motion control terminal board is for the users who use Mitsubishi J2 super servo. With this terminal board, users can ealisy complete wiring with PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134.
-
product
PCB Design and Assembly
Innovative Circuits Engineering, inc
Turnkey services for Printed Circuit Boards: Design, Fabrication, Assembly and Testing
-
product
Digital Input Board
VME-1182A
A multifunctional intelligent controller allows COS, SOE, pulse accumulation, debounce times and time tagging control on a per-channel basis.
-
product
PC/104 Multifunction Analog I/O Boards
104-AIO16A/E
The 104-AIO16A is a high-performance 16-bit resolution PC/104 board which provides speeds up to 500kHz for 16 single-ended or 8 true differential analog input channels. This multifunction board features an excellent price/performance value for precision PC/104-based data acquisition, control, or signal analysis of standalone environmental test stations, compact production test equipment, portable testers, avionics and other applications.
-
product
Test Systems
Testing is more than just finding defects on Printed Circuit Boards. It is also about how to predict defects before they occur. A true economy can only be achieved when you see testing as an integrated part of manufacturing. To achieve this we provide Advanced Diagnostic Tools and Electronic Manufacturing Systems (EMS) that integrate testing with design, manufacturing, and repair.
-
product
3.5" Embedded SBC With Intel® Celeron® J1900 Processor, LVDS/VGA/HDMI, Dual LANs, Audio And ZIO
CAPA843
The CAPA843, a fanless 3.5-inch embedded board, features quad-core Intel® Celeron® processor J1900 SoC (codename: Bay Trail). A pair of SO-DIMM sockets supports up to 8GB of DDR3L 1066/1333MHz RAM. The compact size embedded board CAPA843 was designed with emphasis on expandability, offering two full-size PCI Express Mini Card slots, as well as an exclusive Axiomtek ZIO connector. With excellent thermal design, the 146 x 102mm embedded SBC can handle operating temperatures from -20°C to 70°C, and runs on +10V to +24V DC input. The 3.5” fanless embedded board provides three display interfaces with dual-display operation: HDMI, LVDS and VGA. The Axiomtek CAPA843 is an excellent choice for applications in IoT/M2M-related, industrial control, self-serve terminal, gaming, digital signage, POS, and kiosk.
-
product
PCI Express A/D Board
AD8-1500 Series - Dual 8 bit, 1.5 GS/s
The AD8-1500 series has one or two 1500 MS/sec 8-bit ADCs, 8GB of on-board memory and the ability to transfer data directly into the host computer's memory at over 1 GB/sec. Streaming to the host computer can be performed simultaneously with acquisition to on-board memory, increasing the effective acquisition length by using the host computer's memory. Dual channel boards sample concurrently at twice the input clock frequency, and can also be software selected to run in single channel mode, providing twice the effective memory depth.
-
product
75 Ohm MCX Connectors
Pasternack 75 Ohm MCX connector category includes several part numbers, the majority are RoHS and REACH compliant. 75 Ohm MCX connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. These 75 Ohm MCX connectors are built to precise RF and microwave industry specifications. MCX 75 Ohm connectors are available in jack or plug gender with 75 Ohm impedance. 75 Ohm MCX connector products are available in straight or right angle versions, as well as, bulkhead or mountless options. These 75 Ohm MCX connector designs include crimp/solder or solder attachment methods. As with the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this MCX connector series for 75 Ohm is in-stock. Not only are they in stock, these MCX 75 Ohm connectors will ship the same day as purchased.
-
product
Demonstration Boards
SAMPULSE50GHz and SAMPULSE70GHzANT
The SAMPULSE50GHz and SAMPULSE70GHzANT are demonstration boards for Furaxa InP single channel sampler/pulser ICs. The SAMPULSE50GHz model contains a 2.4mm combined TDR input/output connector to the common sampler/pulser node in the IC. The SAMPULSE70GHzANT is similar, except that instead of a single-ended 2.4mm connector, the sampler IC's differential inputs are fed from a bowtie antenna. In both models, the IC's differential sampler output is converted, using an AD8009 op amp, into a single-ended ground-referenced output that is sent to an SMA jack labeled SAMPLER OUTPUT.
-
product
Moisture Testers for Wood
Here you will find a moisture tester for wood to determine absolute moisture in different wood types. Newly-cut logs can have a moisture content of 80% or more, depending on the type. Since wood shrinks substantially when dried, it must be dried before being used in construction or most other applications. This is most often done using a large furnace called a kiln. The air drying method may also be used, but this is much slower. With the help of the moisture tester for wood you will be able to measure with high accuracy moisture in, not only raw wood, but also rolled paper products, planks, slats, beams, plywood, panels, particle board, main beams, window frames, etc., anything wooden. There are two ways of measuring moisture, these two ways are with or without damaging the material. The majority of types of moisture testers we offer at PCE do not damage the wood, or damage it very slightly.The moisture tester for wood is characterized by the measuring principle and the moisture sensors that can be adapted to it. The moisture tester for wood has special characteristics such as an automatic compensation of temperature. Besides, data can be stored and transferred to a PC or laptop, or characteristic curves can be programmed for specific wood types (only with the model FMD). Our moisture tester are of the highest quality standards in the industry, and are durable and easy to use.
-
product
Standard Pattern Generator Board
BL-PG315-01
The MicroImage PG315 pattern generator is designed for simple size and geometry reference applications. The PG315 will overlay one of five standard patterns including a centered cross line, a centered cross hair, a centered target style symbol, a dot grid (cross dot) array, a hatch grid (crosshatch) array.
-
product
10-32 Connectors
Pasternack 10-32 connector category includes many part numbers, most of which are RoHS and REACH compliant. 10-32 connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. Pasternack 10-32 connectors are built to precise microwave and RF industry specifications. 10/32 connector items are constructed in male or female gender with 50 Ohm impedance. Connectors in 10-32 series are available in straight or right angle versions, as well as, bulkhead or mountless options. These 10-32 connector designs include clamp/solder, crimp/solder or solder attachment methods. Like the other over 40,000 RF, microwave and millimeter wave Pasternack products, this 10-32 connector series is in-stock. Not only in stock, but will also ship the same day as purchased.
-
product
3U Processor Board
CP39104
LinkedHope Intelligent Technologies Co.,Ltd.
Designed for industrial communication, CP39104 is a 3U CPCI serial card compliant with PICMG 2.0 R3.0 specification.CP39104 applies XR17D154 serial communication controller of EXER, and supports 4x RS232/RS422/ RS485. Therefore, CP39104 is highly suitable for testing and measuring in serial data communication applications.LinkedHope® provides CP39104 with a wealth of software drivers and BSP, including VxWorks, Linux, Windows, etc., to enable a wide range of application scenarios.
-
product
Compact PCI Multi-function Decommutator
LS-50-cP
The Lumistar LS-50-cP 3U Compact PCI Multi-function PCM Decommutator offers the greatest flexibility in the industry by incorporating up to 10 functions typically encountered in flight test applications in a single 3U Compact-PCI card slot. Five functions are achieved on the main board (PCM Simulator which can also operate as a BERT, PCM Decommutator, IRIG Time CodeReader, IRIG Time Code Generator, and the same 5 functions can be achieved on the LS-55-DB Multi-Function Decom Daughterboard. CVSD Voice Decoding and h.261 Video Decoding are achieved through software.
-
product
PCI Express 4-Port
7404e
The 7404e PCI Express serial interface provides four multifunction serial ports, each individually field-configurable for RS-232, RS-422, or RS-485. Each serial port utilizes a 16C954 UART with 128-byte Tx/Rx FIFOs that enables data rates to 921.6K bps for reliable high-speed communications in data-intensive applications. This high-performance UART includes 9-bit framing support and is register compatible with legacy 16550 software applications. In addition, the board derives a 62.5 MHz clock from the PCI Express link. This ultra-high-speed clock is divided by a flexible 8-bit clock prescalar with 1/8 steps to provide support for the widest range of standard and non-standard baud rates.
-
product
Relays
Omega offers a broad range of relays including universal remote modules, 24-channel relay output boards, including high-reliability relays, relays for intrinsic safety, panel mount models, and more.
-
product
VXI Register Interface Board
VXI-5524A
*VXI Register Interface mates with user's PCB to form a B or C-size module.* 48 Digital IO Lines - Three 16-bit registers set as latched outputs or gated inputs.* 16 line bi-directional expansion bus for driving external logic.* Digital IO and VXIbus lines are 3.3V logic levels and are 5 V tolerant for compatibility with 3.3V logic and 5V VXIbus signals.* User selectable 3.3 and 5 Vdc puliup voltage on the digital IO lines for sensing switches etc.* The VXI-5524A board is a complete VXI-1 Rev 1.4 and VXI-2 compliant register-based interface.* User configurable model number, manufacturer ID, version and serial numbers.* Two companion component boards available for prototyping IC or RF assemblies.* Companion hardware kits available for building 1, 2 or 3-slot wide modules.
-
product
2-Module ICT System, I317x Series 6
E9902G
Keysight's family of i3070 Series 6 In-Circuit Test (ICT) systems are built on a proven technology foundation, and they improve test efficiency with time-tested software, hardware, and programmability. I3070 Series 6 ICT tester supports a wide range of printed circuit board assembly (PCBA) sizes for applications including IoT and 5G, as well as automotive and energy. The i3070 features a unique design that delivers the shortest signal path between measurement circuitry and devices under test to minimize undesired effects from parasitic capacitance, improve immunity to crosstalk, and eliminate stray signal coupling effects, delivering consistent and repeatable measurements. The Series 6 is fully backward compatible with previous systems and makes highly repeatable measurements.
-
product
16-Port Serial Controller
PMC523
The PMC523 provides a flexible solution for technology insertion by integrating multiple serial I/O channels onto a single board computer (SBC) with a PCI Mezzanine Card (PMC) site. This gives customers affordable protection from obsolescence and a smart evolutionary path to enhanced software ultimately improves performance and increases efficiency.
-
product
Lightning "Emulator" Shield
SEN-39002
Arduino shield, ideal for AS3935 lightning sensor development. The lightning "emulator" generates a RF signal that mimics lightning strikes. This board is in an Arduino Uno form factor, and only uses GPIO and I2C, so can be stacked on many form factors (developed on an Uno and Mega).
-
product
Quad 12.0 Gsps 16-bit DAC FMC+ Module
DAC-Q30
The DAC-Q30 FMC+ module from DEG is a high sample rate, 16 bit quad channel DAC module. The Analog Devices AD9174 DAC device operates at 3.0 Gsps natively and up to 12.0 Gsps in interpolation mode. A VITA 57.4-compliant FPGA Mezzanine Card (FMC+) interface, the DAC-Q30 offers industry wide platform compatibility with the PCIe/VME/VXS/VPX carrier board of your choice. The DAC-Q30 and associated HDL firmware are compatible with AMD FPGAs.
-
product
Industry Pack I/O Products
Acromag IndustryPack mezzanine IP modules deliver maximum I/O density when used with industry-standard IP carrier cards for VME, PCI, CompactPCI or PCI Express. These plug-in Industry Pack modules give you mix-and-match flexibility and high channel density to save your valuable card slots. Combining different IP types on one carrier simplifies the design of a low-cost, custom I/O board.
