-
Product
RF Noise Source
NS-3
-
The NS-3 Broadband RF Noise Generator provides an extremely flat AWGN (Additive White Gaussian Noise) signal from 5 to 2150 MHz. The output level adjusts in 0.1 dB steps over a 30 dB range.The bench-top configuration is standard and an optional two unit rack enclosure is available. The RS232 or USB remote control interface simplifies its use in automated test and factory ATE environments. The NS-3's combination of range, versatility and value make it the ideal general purpose broad-spectrum signal source for bench and ATE applications, including C/N, BER, MER, PER testing and rain fade simulation.
-
Product
RF Filters
-
RF Filters block unwanted frequencies when testing electronic devices for emissions during EMC testing. They attenuate unwanted frequencies and allow the desired signals through. The RF filters isolate the device under test from external RF noise, this increases the reliability and accuracy of the EMC testing by preventing out-of-band noise and harmonics.
-
Product
Wideband Transmitter
SMWB
-
To meet the demands for a variety of RF environments and applications, the “WB” series SM transmitters offer selectable output power of 25, 50 and 100 mW (25 and 50 mW for export versions). With higher power output, the operating range is improved, or, a more secure link can be relied upon for high RF noise environments. Battery life is unchanged with the different RF power selections.
-
Product
Wideband Transmitter
SMDWB
-
To meet the demands for a variety of RF environments and applications, the “WB” series SM transmitters offer selectable output power of 25, 50 and 100 mW (25 and 50 mW for export versions). With higher power output, the operating range is improved, or, a more secure link can be relied upon for high RF noise environments. Battery life is unchanged with the different RF power selections.
-
Product
Partial Discharge Tester (Dry Type)
-
Partial Discharge testing is a way of detecting voids or imperfections in insulators that would lead to overheating and breakdown under normal operating conditions. Due to the nature of the signal being measured, this test is very susceptible to electronic and RF noise and a proper corona-free properly isolated test chamber is required.
-
Product
RF Test Spectrum Measurements over CPRI
Integris 3000
-
Most modern cell tower network configurations place the Remote Radio Head (RRH) at the top of the tower and the baseband unit(BBU) at the bottom of the tower. While this configuration is advantageous for both computational efficiency and mitigation of RF loss across the cable, it means the only place along RF can be accessed is at the top of the tower. This forces field technicians to have to climb the tower to measure and debug RF noise problems.
-
Product
ECM Noise Under RF Test System
BK8020
-
The BaKo Type BK8020 ECM Noise Under RF Test System tests microphones under RF noise, using a ‘Direct Injection Test’ in the frequency range of 5MHz~2.5GHz with an amplitude modulated (AM) disturbance signal of 1kHz. You run the system using the controlling PC, which allows automatic configuration and which runs the test sequence automatically. When you finish testing, you can print data as an MS Excel report or save it for comparison and analysis.
-
Product
Photodetectors
-
Detection of weak light pulses on the few-photon level is crucial for many applications. The Menlo Systems' detector portfolio includes PIN photodiodes with low noise RF amplifiers, ultrafast avalanche photodetectors with integrated high voltage supplies, and detectors based on homo- and heterodyne detection.
-
Product
3D RF Noise Measurment System
EMI-360
-
3D RF Noise Measurement System EMI-360 to realize the new EMC measurement.EMC measurement is possible to realize a low-cost and time reduction.
-
Product
RF Amplifiers
-
UST specializes in the testing, repair and refurbishment of all types of RF amplifiers (broadband and narrowband), microwave amplifiers and millimeter-wave amplifiers: solid state, thin film, traveling wave tube (TWT), low noise RF amplifiers, intermediate power RF amplifiers, limiting RF amplifiers, doubler RF amplifiers, driver RF amplifiers, variable gain RF amplifiers, and active frequency multipliers.
-
Product
Noise Source, 10 MHz to 18 GHz, nominal ENR 15 dB
346B
Noise Source
The Keysight 346B noise source is the ideal companion to Keysight's noise figure solutions. Since it is broadband (10 MHz to 18 GHz), it eliminates the necessity for several sources at different frequency bands. The low SWR of the noise source reduces a major source of measurement uncertainty; reflections of test signals. The 346B's high ENR, low SWR, and variety of connectors make it a general-purpose noise source. Add special option H01 for high ENR (21 dB typical) to measure high noise figure devices, or option H42 for measuring Direct Broadcast Satellite (DBS) low noise block converters.
-
Product
Millimeter-Wave Noise Source, Q-band, 33 To 50 GHz
Q347B
Noise Source
The Q347B waveguide noise source (33 to 50 GHz frequency range), allows you to make accurate noise figure measurements on millimeter-wave devices...
-
Product
SNS Series Noise Source 10 MHz to 18 GHz (ENR 15 dB)
N4001A
Noise Source
The SNS series N4001A noise source is ideal for general purpose use with a low reflection coefficent and a nominal ENR of 15 dB from 10 MHz to 18 GHz.
-
Product
Noise Source, 1 GHz up to 40 GHz
346CK40
Noise Source
The Keysight 346CK40 is the ideal companion to Keysight´s noise figure solutions when working on high frequency applications. Since it is broadband (1 GHz to 40 GHz), it eliminates the necessity for several sources at different frequency bands. The low SWR of the noise source greatly reduces measurement uncertainty, which are commonly reflections of the test signals. This is a coaxial noise source with a 2.4 mm coaxial connector. ENR typically 14 dB at 1 GHz, decreasing to 5 dB at 40 GHz (typical).
-
Product
Phase Noise Analyzer and VCO Tester
FSWP
Phase Noise Analyzer
The R&S®FSWP phase noise analyzer and VCO tester features very high sensitivity thanks to extremely low-noise internal sources and cross-correlation. It can measure phase noise and amplitude noise in mere seconds on highly stable sources such as those in radar applications. Additional options such as pulsed signal measurements, residual phase noise (including pulsed) characterization and integrated high‑end signal and spectrum analysis make the R&S®FSWP a unique test instrument.
-
Product
3.5 Mm, 3.5 Mm (3.5 Mm–3.5 Mm) RF Cable
137446-03
RF Cable
RF Cable, 3.5mm (M) to 3.5mm (M), 3.000 Meter Length, 26.5 GHz, Phase Stable
-
Product
RF Bridge, 50 Ohm, 300 kHz to 3 GHz
86205B
RF Bridge
The Keysight 86205B high directivity 50 ohm RF bridge offers unparalleled performance in a variety of general-purpose applications. It is ideal for accurate reflection measurements and signal leveling applications.
-
Product
Low-Noise Filter, 210 V / 3 A
N1298C
Noise Filter
The N1298 Series power source accessories are a collection of low noise filters for the Keysight B2960 Series precision source / measure units (SMUs).
-
Product
LXI Dual Bank, 12:1 MUX 75 Ohm 1GHz F-type
60-722-002
RF Multiplexer
Our 60-722 High Isolation RF Multiplexer is suitable for switching 75 ohm signals up to 1GHz. With the choice of single or dual multiplexer banks each with 12 channels, it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted F-type connectors.
-
Product
3.5 Mm, 3.5 Mm (3.5 Mm–3.5 Mm) RF Cable
137833-0300
RF Cable
RF Cable, SMA (M) to SMA (M), 0.300 Meter Length, 26.5 GHz
-
Product
PXI-2797, 40 GHz, 50 Ω, 6x1 (SP6T) Terminated PXI RF Multiplexer Switch Module
782357-01
RF Multiplexer
40 GHz, 50 Ω, 6x1 (SP6T) Terminated PXI RF Multiplexer Switch Module—The PXI‑2797 offers a high-density, terminated multiplexer with dual 6x1 multiplexer banks in the same module. The internal termination of the PXI‑2797 helps prevent high-power reflections that arise from open channels on the module. It is ideal for passing high-order harmonics from PXI RF Signal Upconverter modules or routing multiple sources to PXI RF Signal Downconverter modules.
-
Product
3.5 Mm-3.5 Mm RF Cable
136691-0400
RF Cable
RF Cable, SMA (M) to SMA (M), 0.400 Meter Length, 26.5 GHz, Temp Stable
-
Product
PXI Octal SPDT RF Switch 6GHz 50 SMA Terminated
40-880-004
RF Switch
A range of 50Ω SPDT RF switching with automatic termination of unused signals. Available as a dual switch in a 1 slot PXI module, a quad switch in a two slot PXI module or hex and octal switches in three slot PXI modules.
-
Product
USB Smart Noise Source, 10 MHz to 26.5 GHz, Nominal ENR 15 dB
U1831C
Noise Source
The USB-powered U1831C provides broadband noise figure measurements from 10 MHz – 26.5 GHz with modular signal analyzer and benchtop X-Series signal analyzers.
-
Product
PXI Octal SPDT RF Switch, 8GHz 50Ω SMA, Terminated
40-880A-004
RF Switch
The 40-880A-004 is an octal SPDT 50Ω RF switch with 8GHz bandwidth. The 40-880A range of SPDT switches have automatic termination of unused signals and are available as a dual switch in a 1-slot PXI module, a quad switch in a 2-slot PXI module or hex and octal switches in 3-slot PXI modules.
-
Product
75 Ohm BNC to BNC Cable Assembly
40-977-701-1m
RF Cable Assembly
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
Product
Noise Figure Analyzer, Multi-touch, 10 MHz to 7 GHz
N8974B
Low-Frequency Noise Analyzer
The N8974B high performance noise figure analyzer is designed to make fast, accurate and repeatable noise figure measurements. When paired with an SNS Series noise source and U7227 Series USB preamplifier the ENR data from the SNS and USB preamplifier data automatically downloads into the N8974B.
-
Product
Noise Figure Analyzer, Multi-touch, 10 MHz to 26.5 GHz
N8975B
Low-Frequency Noise Analyzer
The N8975B high performance noise figure analyzer is designed to make fast, accurate and repeatable noise figure measurements. When paired with an SNS Series noise source and U7227 Series USB preamplifier the ENR data from the SNS and USB preamplifier data automatically downloads into the N8975B.
-
Product
50 Ohm BNC to BNC Cable Assembly
40-977-501-0.5m
RF Cable Assembly
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
Product
3.5 Mm, 3.5 Mm (3.5 Mm–3.5 Mm) RF Cable
137833-0600
RF Cable
RF Cable, SMA (M) to SMA (M), 0.600 Meter Length, 26.5 GHz
