Leakage Current Testers
-
Product
Sound Harmonics and Current Analyzer
H74050100
Audio Analyzer
This analyzer is used as end of line control for electro mechanic components with electric motors, with or without mechanical reduction. While the motor is running at nominal speed, a spectrum and temporal analysis of the sound as well as a current consumption test is performed. Statistical analysis of the data acquired is also performed real-time, expediting the PASS/FAIL decision of the DUT.
-
Product
Current Transformers
-
Supreme Instrument Laboratories
Portable Low Tension precision grade multi ratio Current Transformers, housed in laminated wooden cabinet, wound primary with suitable terminals on highly insulated bakelite panel upto 100 Amps. For higher ranges, a centre hole is provided for passing primary conductors for desired range.
-
Product
Current Probe
PA-629
-
*Maximum Current Value: +/- 200ADC, 140A RMS*1mA = 10mA, 100mA (switchable)*Rising Time: 1.2uS*Bandwidth: DC ~ 300kHz*Over Range Indicator*Battery, AC Power Supply Adaptor (free), dual usages
-
Product
Split type AC Current Sensor
CTF-50A
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
* Suitable for current measurements of terminal feeder. * Wire stopper is equipped for the slipping protection. * The special connector is not necessary as the output terminals are provided. * Open circuit protection and nonflammable plastic material.
-
Product
Current clamps
-
Precision ammeters determine the intensity of an electric circuit without interrupting the current flow.
-
Product
High Voltage Surge Current Monitors
HVSCM
-
Designed to be used with the Model HVST High Voltage Surge tester. The Surge Current Monitor allows simultaneously surge testing 20 units. The Surge Current Monitor monitors the current going through each unit under test at the time of the surge. If a unit under test breaks down or leaks, the Surge Current Monitor will identify the bad unit by lighting the corresponding LED. The most important features of the surge tester are its ability to test the entire winding insulation system. A high voltage surge generates turn to turn, coil to coil, and phase to phase voltage stress, as well as ground insulation stress. When used as a dielectric test, accurate voltage readings are essential. The HV Surge Tester monitors the voltage directly across the winding under test. In production testing we expect that most of the time the devices will pass. In the event that one should fail, the failed device would be removed and then all the parts would have ot undergo another surge test. Since most devices pass most of the time, simultaneous surge testing can be a real time saver.
-
Product
Current Probe
PA-622
-
*Max. ±100A DCA*Resolution: ≧10mA*Bandwidth: DC~300KHz*Rise Time: 1.2 uS*Over Range Function*10mV/A, 100mV/A Range*Adaptor/Battery Input*Separating Design,Convenient Durable
-
Product
Impulse Current Measuring Shunts
ICMS
-
The Impulse Current Measuring Shunts ICMS are new designed tubular shunt types with best response behavior to match the high performance of the TR-AS digital recorder for comparative current measurements. A 1st partial response time less than 10ns and a settling times less than 20ns show the advantage of these shunts. They show no initial overshoot peak, no oscillations and do not need compensation box to optimize the transient behavior as known from e.g. cage shunts.
-
Product
Rogowski Coil Current ProbesTOP
-
*Switching current waveform and pulse response characteristics of power devices*Current measurements of inverter system*AC current measurements (at large DC offset)*Impulse high current measurements*Bus Bar high current measurements
-
Product
Split Type AC Current Sensor
CTF-16
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*For AC current and power measurements.*Wide measuring range (AC 0.1～100A).*Compliant with RoHS drective.
-
Product
Stand-Alone Current Sensors
-
The Aanderaa Current Sensors are based on the backscatter acoustic Doppler principle.
-
Product
Integrated Current Sensors
HMSR series
-
The HMSR is a new generation of high insulated Integrated Current Sensor from LEM. These product family provides a robust, compact and very accurate solution for measuring DC and AC currents in all highly demanding, switching power applications for commercial, industrial. HMSR is a micro core based open loop sensor with a reinforced insulation and overcurrent detections (user configurable and factory set). These features make the device suitable for high voltage applications requiring high precision and strong immunity against external field. The primary conductor (pins 1 and 8) has very low electrical resistance and dedicated pads d
-
Product
Wide Range Flexible Current Probe
EFX6000
-
The EFX6000 is a flexible AC current clamp utilizing the Rogowski principle. It can be used to measure currents from 1 amp to 6000 Amps in 2 auto-ranges, over a wide frequency range to 10kHz. The flexible and lightweight measuring head allows quick and easy installation in hard to reach areas, around large conductors and where access to confined or tight spaces is a problem. It requires no batteries or external power supply.
-
Product
Low Current Probe 80A
695
-
Great tool for accurate measurement of low current. Use with your graphing meter or lab scope to view current waveforms on fuel injectors, fuel pumps, primary ignition coils and more. Also works very well with digital multimeters. Resolution of 10 milliamps is low enough for most parasitic drain testing. In addition, the clamp opening of 1/2 inch is large enough to clamp over most negative battery cables for those parasitic drain tests.
-
Product
Primary Current Injection
PCI-600
-
The VIC Model PCI-600 is a programmable, high-current source that is designed specifically for utility-substation applications. This alternating current(ac) test device is used primarily for injection testing of protective relays. This same device can also be used for testing thermal, magnetic and solid-state motor-protection relays and molded-case circuit breakers.
-
Product
Testing of Current Measuring Transformers
-
All components from this category can be integrated into an existing current transformer test system. When selecting CT test components, both the type of converter to be tested and the required current are important.
-
Product
Single-Stage Current Sensors
-
The robust low-noise single stage current sensors are available with input inductances from 24 nH to 1.8 µH and a flux noise of 1.2 µPhi0/sqrt(Hz).
-
Product
Automotive Tester
7612A
-
This is the device to test 3 popular vehicle relays. The testing result will be displayed by LED indication. Technician is able to use the device to figure out the condition of the relay, and so speculating the problem in the vehicle. Use the relay adapter to plug into the relay tester, suitable to connection multiple styles relay.
-
Product
Continuity Tester
1670
-
Peaceful Thriving Enterprise Co Ltd
1. For automotive, marine, aircraft and home appliances. 2. Detect open circuit in fuses, diodes, switches, sockets and wires.
-
-
Product
Capaciter Tester
KS-1600
-
Konstar Electric Industrial Co., Ltd
It is a dial instrument, and has the stable function and high reliability. It is driven by the battery. The instrument makes use of the indicator plate(102*79mm), thus displays clearly.This instrument can test the data of on-line capacitive resistance and on line impedance. It is an excellent instrument and an ideal tool for the people in labs, factory and household. When testing the mounted capacitor, it does net need to be completely out of power nor do the meter, and the meter can be testing continuously.
-
Product
Current Recorders
-
A range of Low Cost Voltage, Current and Energy Recorders (Analysers, Analyzers) allows users to check loading and voltage performance, as well as Power and Energy surveys. A great replacement for a Hawk 5000 Meter.
-
Product
Microhardness Tester
-
By adopting the Load-cell load system, multi-stage load switching is possible.
-
Product
Insulation Testers
-
Can be used for quantitative and qualitative analysis of insulation. It also automatically measures voltage, capacitance and residual current.
-
Product
Armature Tester
DS-e/d Series
-
Shanghai Aoboor Electric Co., Ltd.
Applicable to accurate test of armatures made by single-fork, double-fork or large and small bar winding process; and test of armatures made by piezoresistor, carbon commutator, equalizer, double-insulation and other special process.
-
Product
High Current Connectors
-
C.C.P. Contact Probes Co., LTD.
60% lower extraction force, 80% higher current than other common connectors. The numbers speak for themselves.
-
Product
Precision Current Sources
-
HighFinesse Precision Current Sources have been developed for experiments and quantum technologies in the areas of cold-atom and solid state physics. The linearly regulated BCS (Bipolar Current Source) and UCS (Unipolar Current Source) series deliver highly stable, low noise source currents for high precision magnetic field control. The current output is floating or is on a used defined potential. Ultrafast response to control signals and trigger functions, clear grounding, connection and signal isolation schemes make the integration of the current sources into complex experimental systems easy.
-
Product
Folding Tester
FOT-01
-
Jinan Leading Instruments Co., Ltd.
FOT-01 Folding Testeris designed according to relevant standards and adopts modern mechanicalphilosophy and computer processing technology. Folding tester complies with relevant standard. It is suitable to test fatigue strength of paper, paperboardand other sheet material, which thickness is less than 1mm.
-
Product
Insulation Tester
1kV Megohmmeter
-
*Calculations (automatic)*Potential Index and Dielectric Absorption Ratios*Tests Continuity, Resistance and Frequency Measurements*Programmable Alarms*Insulation Test, Resistance, Continuity*Hazardous Voltage Alert (Icon) if voltage is >70 volts 5.) On Board Timer, +1/- 1 sec
-
