Phase Sequence Indicators
find order of ac vice versa voltage / current cycle peaks in a polyphase system..
-
Product
Regenerative AC Emulator, 600 VAC, 125 A, 90 KVA, 3‑Phase
SL1203A
AC Emulator
The SL1200A series was designed to handle all your 3-phase AC test needs up to 1200 VAC, from 30 kVA to 630 kVA without the need for a transformer. Two voltage ranges are available: 600 VAC and 1200 VAC. The 600 VAC models are ideal for low voltage inverter test as well as EV and EVSE charging test applications. The 1200 VAC models allow for (HVRT) testing at the IEC LV-AC limit without the need for a large, complex test setup.
-
Product
3 Phase Voltage Transducer
-
Converts a three phase, 600 VAC, 50/60 Hz power system to three proportional 0 to 5 volt DC outputs.
-
-
Product
Phase Frequency Detectors
-
Analog Devices phase frequency detectors offer high performance and ultralow phase noise in a low cost, compact package. Our devices can significantly improve frequency lock time, and include automatic and configurable lock detect indicators.
-
Product
Cable Identification System & Cable Phasing System
Impulse Phaser
-
With the introduction of direct buried, solid dielectric primary voltage cables, the IMPULSE PHASER has come into greater prominence for safely and accurately identifying buried primary cables, including jacketed neutral designs. The IMPULSE PHASER has been accurately used on paper insulated, lead covered feeders in excess of 20 miles and even on submarine cable 300 feet underwater.
-
Product
Digital Weighing Indicator | Process Meter | Panel Meter
-
Mantracourt’s digital weighing indicator and panel meter modules are compatible with a wide range of sensors and transducers, including volts, amps, temperature, frequency, speed, load, force, pressure, torque, LVDT, RVDT and many more. The digital architecture offers simple one-pass calibration and fast setup.
-
Product
Point on Wave Synchronous Test Sequencer
-
The Portable Point on Wave Synchronous Test Sequencer is India’s only system that helps in time synchronizing the control signals during short circuit tests performed on medium and high voltage switchgear and control gear.
-
Product
Single Phase Powerline Monitors
-
a Voltage disturbance detector and recorder. This device is designed to be plugged into a 120V or 240V AC line and will monitor this line for voltage disturbances and temperature or Humidity variations.
-
Product
4 Digit Angle Position Indicator (API)
TA-900
-
This has been the New standard in Angle Position Indicators. 4 digit API has fault monitoring for both low-level and loss of signal (LOS) and this status is shown on the front panel led. The unit provides simultaneous connection of both synchro and resolver devices.
-
Product
Single Phase Din-rail Multi-rate kWh Meter
SY 1025
-
Hong Kong Songyang Industrial Ltd.
Type SY1025 single phase DIN rail watt-hour meter is a kind of new style single phase electronic multi-rate watt-hour meter, energy data display adopt 7 digits wide temperature type crystal display, with many functions of multi-rate (time-of use) energy measurement, infrared carrier wave communication and RS485 serial port communication reading meter, etc.
-
Product
Phase Domain Induced Polarization/Resistivity Instruments
ULTRA MiniRes
-
*Light weight yet durable*Low power consumption*Lowest cost in the industry*Exploration to greater than 1000 feet**2.5 HertzMEASURES:*Earth resistivity*Induced polarization
-
Product
Internally Ruggedized Phase Stable Test & Measurement Test Lead Assemblies
Storm-Test®
-
- Engineered to provide precise measurements with stable electrical performance- Excellent loss, VSWR, & phase/amplitude stability with flexure. - Internally ruggedized cable construction delivers longer life, repetitive mating and prevents crushing, bending & twisting- Accurate & repeatable measurements - Performance tested prior to shipment
-
Product
Three Phase Site Energy Meter Test Instrument Type KP-P3001-A
-
Bofa Instrument & Equipment Co., Ltd
Three-phase site energy meter test instrument type KP-P3001-A (without voltage and current source) is an ideal instrument to test all kind three-phase energy meters accuracy below 0.2, especially for meters on site. When we want test a meter errors, the tested meter must be on load condition (or we can say the tested meter must be working). The instrument can test the errors, by comparing energy impulse from the tested meter with energy impulse from the reference meter which inside the instrument. The equipment is box structure and weight is very light, easy to carry, it is very convenience to test the installed meters on site.
-
Product
Three Phase Power Sources
PS3
-
The PS3 three phase power source was designed to provide a stable alternating current and voltage source for three phase electricity meter test equipment.
-
Product
Phase Modulated Driver
-
The Phase Modulation Capable RF Driver / Stabilizer is an eight channel, two phase RF driver intended to drive devices such as the Harris H-401. The driver provides both amplitude and phase modulation capabilities in a single unit. The device can be operated in driver mode where the operator has full control over amplitude, frequency, and phase, or in stabilizer mode where the driver automatically adjusts the operating parameters based on optical feedback from an optical pick-off point.
-
Product
3 Phase Flexible AC Current Probe
DRP 503/18
-
The new DRP 503/18 is a 3 Phase Flexible AC current Probe utilising the Rogowski principle, with 3 channel integrator housed in DIN Rail Mounted Enclosure. The flexible and lightweight measuring head allows quick and easy installation in hard to reach areas and with large conductors.
-
Product
Phase Noise Measurement Up To 70 GHz
S930317B
-
S930317B enables phase noise measurements using a PNA or PNA-X vector network analyzer. Simplify your measurement workflow by measuring phase noise on the same connection as your network analysis measurement of 2-port active devices up to 70 GHz, without needing to connect a spectrum analyzer or harmonic mixer.
-
Product
Digital Phase Shifters
-
An electronic device that changes the timing (phase) of an RF/microwave signal in precise, stepped increments, controlled by digital signals (like 0s and 1s), not continuously like analog versions.
-
Product
Phase Noise Measurement Solution, 50 kHz to 110 GHz
E5505A
-
The Keysight Technologies E5500 Series of phase noise measurement solutions offers the most flexible set of measurements on one-port VCOs, DROs, crystal oscillators and synthesizers. Two-port devices, including amplifiers and converters, plus CW, pulsed and spurious signals can also be measured. The E5500 measurements include absolute and residual phase noises, AM noise, and low-level spurious signals. The stand-alone instrument architecture easily configures for various measurement techniques, including the PLL/reference source technique, residual and FM discriminator methods.
-
-
Product
HOT STICKS & PHASING STICKS
HS-15
-
Hot Sticks and Phasing Sticks are voltmeters designed so to permit testing of high-voltage lines or bus bars. The meter is conveniently located, and tilted downwards for easy reading to 5% of full scale.
-
Product
3 Phase Meter - Clockwise
135007
-
IEC 1010 Rating: 1000V Cat III/600V Cat IV Double/Reinforced InsulationFeatures: For Use In The Installation and Operation Of 3 Phase Equipment.
-
Product
Arbitrary/Function Generator,2 Ch,150 MHz,16 bit,128Mpts/Ch,6 Vpp output, Wave Sequencing
T3AWG2152
Function Generator
Arbitrary/Function Generator,2 Ch,150 MHz,16 bit,128Mpts/Ch,6 Vpp output, Wave Sequencing.
-
Product
Portable Multi Phase protection relay test set with GPS
TEST-630
-
Beijing GFUVE Electronics Co.,Ltd.
Test-630 multi Phase Universal protection relay test set have 6U6I output, it is a universal protection relay tester with eight pairs of binary input and four pairs of binary output
-
Product
Single Phase DC Injection Set Kit
PDC120A/PDC200A
-
PDC120A/PDC200A Single Phase DC current injection set kit is portable test set which could generate DC current for the various testings in railway transportation, HVDC converting stations, etc.
-
Product
Digital Temperature Indicators
-
Premier's Temperature Indicators are commonly used for applications like monitoring of melting furnaces, determining completion of chemical analysis, monitoring of conveyors, checking completion of heating cycle, monitoring of moulds and dies, preheating temperature confirmation, determining temperature rise, preforming heat treatment, checking temperature in manufacturing process, transporting chemicals, laying pipelines with wall and sub sea temperature measurements.
-
Product
Turns Ratio Meter 1 Phase
TR-1 / TR-1P
-
Raytech Single Phase Transformer Turns Ratio Meter TR-1/P was designed to be a rugged and reliable automatic transformer Ratiometer. This system has a high degree of accuracy and will test ratios to 4000:1. The design of this test system is based upon the popular Raytech Automatic Three Phase test set: TR-Mark III.
-
Product
Phase Sequence Testers
-
UEi Test & Measurement Instruments
Is used for detecting the sequence of the supply in three-phase electric circuits.
-
Product
High Speed Phase Inverter - Buffer
WMA-IB-HS
-
The WMA-IB-HS can be used to double the output voltage of two high voltage amplifiers by driving them in bridge mode, or as high impedance input buffer while maintaining precision, high speed and low noise. Because of its high bandwidth, the WMA-IB-HS model is ideal for the Falco Systems WMA-100 or WMA-300 amplifiers. It can also be used with all other Falco Systems HV amplifiers, or even with high voltage amplifiers of another brand.
-
