-
Product
Regular Flex I/O For Remote Switch
98R17500401
-
Flex I/O expansion on the front panel for same-side cablingCompatible with MIC-7500, MIC-7700, MIC-770, MIC-7900
-
Product
DB9M-Pigtail, 9-Pin D-SUB Male to Pigtail I/O Cable, 1 m
157867-01
Multifunction Cable
9-Pin D-SUB Male to Pigtail I/O Cable, 1 m
-
Product
PXIe-7865, Kintex-7 160T FPGA, 24-Channel AO, 1 MS/s, PXI Multifunction Reconfigurable I/O Module
787355-01
Multifunction Reconfigurable I/O
PXIe, Kintex-7 160T FPGA, 24-Channel AO, 1 MS/s, PXI Multifunction Reconfigurable I/O Module - The PXIe-7865 features flexibility of timing and synchronization with a user-programmable FPGA for onboard processing and direct control over I/O signals. The PXIe-7865 provides 24 analog output, 2 analog input, and 32, 5V input-tolerant digital I/O channels connected to a Kintex-7 160T FPGA to help you design applications for hardware-in-the-loop testing, custom protocol communication, sensor simulation, and high-speed control. You can use the dedicated A/D converter (ADC) for independent timing, individual channel triggering, and multirate sampling. Additionally, the PXIe-7865 includes peer-to-peer streaming for direct data transfer to other PXI Express modules.
-
Product
6U CompactPCI Multifunction I/O Board
CPCI-MFIO-6U
Multifunction I/O
The CPCI-MFIO-6U is a 6U CompactPCI multifunction I/O board. The CPCI-MFIO-6U offers 32 channels of 16 bit A/D, four 16 bit D/A, 16 digital I/O, counter / timers, and one PMC expansion slot for additional I/O. There is a local 60 Mhz TMS320C31DSP processor to supervise all the I/O activity. The DSP can be programmed by the end user to execute application specific code. The CPCI-MFIO-6U is ideally suited for factory automation, automatic test equipment, test & measurement, and control systems.
-
Product
Mezzanine FPGA I/O Module
DAC-MOD1
-
Curtiss-Wright Defense Solutions
Simple analog IO to a processor is no longer enough. Software Defined Radio (SDR), RADAR, and telecommunications applications demand closely coupled high performance processing.
-
Product
IP-Parallel-IO
-
IP Compatible card with 48 programmable TTL IO or 24 - RS422 / RS485 compatible differential pairs. 5 mixed combinations available. Filtered or direct input. Programmable interrupt from each IO [TTL or differential]. 2 counter timers. Waveform generator.
-
Product
Digital I/O
-
Curtiss-Wright Defense Solutions
Curtiss-Wright Digitial I/O cards include interfaces to LVDS, Camera Link, Serial intrefaces, CANbus and customizable I/O. With over 20 years experience in the design and production of top quality COTS signal acquisition hardware, we deilver PMC, XMC and PC/104 modules that can cope with the toughest operating environments.
-
Product
LVDS Digital I/O with Virtex-6 FPGA - 6U VPX
Model 57610
-
- 32 or 64 bits of LVDS digital I/O- One or two LVDS clocks- One or two LVDS data valid- One or two LVDS data suspend- Supports LXT and SXT Virtex-6 FPGAS- One or two DMA controllers move data to and from system memory- Up to 2 or 4 GB of DDR3- PCI Express (Gen. 1 & 2) interface up to x8- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O to the carrier board- Ruggedized and conduction-cooled versions available
-
Product
16-bit, 100KHz, 16SE/8DIFF A/D Inputs; 4 14-bit, 30KHz D/A Outputs, 4 24V Digital I/O, All Isolated
CPCI-3120-16-4
-
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
Product
2-slot Fanless Industrial System With LGA1151 Socket 7th/6th Gen Intel® Core™ I7/i5/i3 & Celeron® Processor, Intel® Q170, Front-access I/O, PCIe And PCI Slots
IPC962-512-FL
-
The IPC962-512-FL is powered by the 7th/6th generation Intel® Core™ and Celeron® processors (codename: Kaby Lake/Skylake) with the Intel® Q170 chipset. It is equipped with dual DDR4-2133 SO-DIMM slots with up to 32GB system memory. The ultra-compact industrial computer supports two swappable 2.5" HDDs; moreover, it offers flexible expansion options with one I/O module slot and two PCI/PCIe slots. It also has a wide operating temperature range of -10°C to +60°C and a 24VDC (uMin=19V / uMax=30V) power input for severe environments. According to the features above, this rugged IP40 industrial PC is a great choice for a wide variety of Industrial IoT applications including automatic optical inspection, digital signage, motion control, and factory automation.
-
Product
PXIe Semi-Dynamic Digital I/O Module, 32-Channel
42-419-003
Digital I/O Module
The 40-419-003 (PXI) and 42-419-003 (PXIe) are a 32-channel digital I/O modules suitable for operating external devices, such as power, RF and high voltage relays, solenoids and lamps. They can also be used for interfacing with external logic such as a programmable instrument with a BCD interface depending upon the module’s driving capabilities.
-
Product
Relay I/O Modules
XTA Series
-
These modules are intended for use with BusWorks XT Series discrete I/O or other digital output modules for the purpose of driving high energy loads.
-
Product
Advanced Flex I/O For NVMe M.2
98910770401
-
Flexible expansion for additional I/O and functions in MIC-7 systemsExpansion on the front for same-side cabling for easy maintenanceKeeps compact size, fanless design, and wide operating temperate advantages of MIC-7 seriesSupports NVMe M.2 SSD via PCIe x4, faster read/write speed than SATASpecial design NVMe heatsink with thermal pad, compatible with different NVMe for heat dissipationCompatible with MIC Regular FIO, i-Module, and Advantech iDoor
-
Product
Remote I/O Systems
-
The clear assignment of a signal to a terminal while maintaining the existing instrumentation and wiring is a major advantage of remote I/O . A second is the significantly reduced wiring through the use of a bus interface to the control system - remote I/O offers the best of two technologies and is therefore ideally suited for modernizing and expanding process plants.
-
Product
I/O Board With Two COM, Four USB 3.0, One Gigabit LAN, And HDMI For PICO880, PICO500, PICO300
AX93276
-
*Specifications: 1 x RS-232/422/485, 1 x RS-232, 4 x USB 3.0, 1 x HDMI, 1 x Gigabit LAN, 1 x Power On, 1 x Reset, 2 x LED*Dimensions: 118 x 40 mm*Compliant products: PICO880, PICO500, PICO300
-
Product
PXI Digital Reconfigurable I/O Module
ITA
PXI Digital Reconfigurable I/O Modules feature a user-programmable FPGA for onboard processing and flexible I/O operation. You can completely control the synchronization and timing of all signals and operations along with custom onboard decision making. The PXI Digital Reconfigurable I/O Module is suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware-in-the-loop (HIL) test, custom communications protocols, bit error rate testing, and other applications requiring precise timing and control.
-
Product
Digital Module For Remote I/O
ITA
Digital Modules for Remote I/O provide 24 V digital inputs or outputs and offer 1‐, 2‐, 3‐, and 4‐wire spring terminal connection options. You can use inputs as counters or standard digital inputs, and you can adjust filter time to improve measurement quality. Inputs can include a built‐in power supply for sensors. Output modules feature circuit and overload protection and can drive up to 500 mA per channel, up to 8 A per module.A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the Digital Module for Remote I/O from a NI real‐time controller. You can use remote I/O hardware to add low‐cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high‐speed or specialty measurements.
-
Product
Isolated Digital I/O DAQ Cards
-
Advantech isolated digital I/O cards have a wide range of products lines in PCI-bus, isolated DIO, ISA-bus, PC/104 and CPCI platforms.
-
Product
Bi-Directional Differential-TTL I/O PXI Card
GX5642
Instrument Card
The GX5642 is a 3U PXI instrument card that can be used for general data acquisition, process control, Automatic Test Equipment (ATE), Functional Test, and factory automation applications. The GX5642 consists of 64 bi-directional TTL-to-differential LVDS I/O channels. Each channel has two ports (TTL and LVDS) and can be individually set to operate in either conversion or static I/O modes.
-
Product
32-CH/64-CH Isolated Digital I/O PCI Express Card With Digital Filter
AX92351
-
The AX92351 is a 64-ch isolated digital I/O PCI Express card with 2,000VDC isolation protection. This high-density digital I/O card with high-speed PCI Express x1 bus is excellent for use in applications requiring digital control or monitoring, such as semiconductor machinery, PC-based industrial machinery, programmable I/O logic control, and process status monitoring. The AX92351 features 32 isolated digital input channels and 32 isolated digital output channels with isolation protection of 2,000V for industrial applications where high-voltage isolation is required. It is equipped with a board ID feature for easy identification of multiple cards in single system. There is a digital filter function to prevent input signals from carrying noise or a chattering. Each isolated input has a sink or source current which supports dry and wet contact for maximum application flexibility. The card has a wide range of input voltage from 10 to 30V to meet most industrial application needs. The AX92351 also provides two interrupt sources on digital input channels. Digital output has open controller and supports maximum 30VDC. The read-back function is another useful function that allows monitoring each output port.
-
Product
Reconfigurable FPGA w/ AD/DA & Digital I/O PCIe Mini Card
TMPE627
-
The TMPE627 is a standard full PCI Express Mini Card, providing a user programmable Xilinx Artix-7 7A50T FPGA. The TMPE627 provides 14 ESD-protected 5 V-tolerant TTL lines. All I/O lines are individually programmable as input or output. TTL I/O lines can be set to high, low, or tristate. Each TTL I/O line has a pull-resistor to a common programmable pull-up voltage that can be set so +3.3 V, +5 V and GND.
-
Product
LVDS Digital I/O with Kintex UltraScale FPGA - XMC
Model 71810
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Supports Xilinx Kintex Ultrascale FPGAs- Front panel digital I/O can be used as a status and control or data interface- PCI Express (Gen. 1, 2 & 3) interface up to x8- VITA 42.0 XMC compatible with switched fabric interfaces- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Ruggedized and conduction-cooled versions available
-
Product
Digital Waveform Acquisition, Digital I/O, Pattern Generators
-
Digital I/O cards, pattern or pulse generators and digital data acquisition cards are all focused on digital signals. Input and output signals have two logic levels called low state (0) and high state (1). The electrical representation of these logical levels depends on the logic family and the supported I/O standard.
-
Product
AdvintRIO™ Reconfigurable I/O
SNAKEHEAD
-
The Snakehead platform employs aNI CompactRIO (cRIO) system consisting of an embedded controller, chassis, and NI C Series I/O modules.Snakehead systems are not dependent on a separate host computer. They offer both Ethernet, and Wi-Fi connectivity to powerful real-time controller with a user-upgradable backplane that includes a high performance field-programmable gate array (FPGA). Snakehead provides stand-alone embedded execution for deterministic LabVIEW Real-Time applications. These units are designed for ruggedness, reliability, and low power consumption. The heart of Snakehead systems is the reconfigurable I/O (RIO) FPGA core. The RIO core has an individual connection to each I/O module and is programmed using easy to use elemental I/O functions to read or write signal information from each module
-
Product
I/O Board
VME-6500 6U
-
The VME-6500 is a 6U VME Multifunction I/O board that can deliver in a single chassis slot the analog and digital I/O capabilities that could previously have occupied four slots, and can therefore make a significant contribution to substantially enhance performance and functional density. A high density and versatile design it provides 8 analog inputs and outputs as well as 16 digital inputs and outputs, all in a single 6U double Euro form factor.
-
-
Product
8 RTD/6DI/8DO IoT Modbus/OPC UA Ethernet Remote I/O
ADAM-6315
-
OPC UA empowers Modbus I/O users to access the industrial IoT world.OPC UA I/O links SCADA and the cloud without the need for gateways, accelerating OT and IT convergence.Hardware and software double security levels to prevent being hacked.Cost-effective: high I/O density and daisy-chaining solution saves cost.
-
Product
FMC Expansion I/O Module.
SI-MOD32xx
-
The SI-MOD32xx is a family of high resolution, FMC form factor, high channel count multi function data acquisition and control modules that plug into any SI-DSP or FPGA carrier card.
-
Product
USB-6366, 8 AI (16-Bit, 2 MS/s), 2 AO (3.33 MS/s), 24 DIO USB Multifunction I/O Device
782264-01
Multifunction I/O
8 AI (16-Bit, 2 MS/s), 2 AO (3.33 MS/s), 24 DIO USB Multifunction I/O Device - The USB-6366 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB-6366 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
4-Ch, 24-Bit, 192 KS/s USB 3.0 I/O Module For Sound And Vibration (With AO And Tachometer)
USB-5801
-
USB 3.0 SuperSpeed and daisy chainable by built-in USB hub4x simultaneously sampled analog inputs, up to 192 kS/s24-bit resolution ADCs with -94 dB total harmonic distortion plus noise (THD+N)Built-in anti-aliasing filter2 mA integrated electronic piezoelectric (IEPE) excitation currents2 analog outputs with update rate up to 192 kS/s24-bit resolution DACs with -90 dB total harmonic distortion plus noise (THD+N)2 tachometer inputs for period or frequency measurement4-ch isolated digital input and 4-ch isolated digital output
